Collecting Information
Port Information
Port 1 | IP: | ____.____.____.____ |
| Netmask: | ____.____.____.____ |
Port 2 | IP: | ____.____.____.____ |
| Netmask: | ____.____.____.____ |
Port 3 | IP: | ____.____.____.____ |
| Netmask: | ____.____.____.____ |
Port 4 | IP: | ____.____.____.____ |
| Netmask: | ____.____.____.____ |
The internal interface IP address and netmask must be valid for the internal network.
General settings
Administrative account | User name | admin | |
settings |
|
| |
Password | fortidb1!$ | ||
| |||
Network Settings | Default Gateway: | ____.____.____.____ | |
| Primary DNS Server: | ____.____.____.____ | |
| Secondary DNS Server: | ____.____.____.____ |
A default gateway is required for the unit to route connections to the Internet.
Factory default settings
Port 1 interface | 192.168.1.99 |
Port 2 interface |
|
Port 3 interface |
|
Port 4 interface |
|
|
|
To reset the unit to the factory defaults, in the CLI type the command: exec reset
Configuring
Web-based Manager
Use the following procedure to connect to the
To connect to the web-based manager
1.Connect the Port 1 interface of the unit to Ethernet port of the management computer. Use a
2.Configure the management computer to be on the same subnet as the Port 1 interface. To do this, change the IP address of the management computer to 192.168.1.2 and the netmask to 255.255.255.0.
3.To access the
4.Type admin in the Name field, type fortidb1!$ in the Password field, and click Login.
After connecting to the
To configure interfaces
1.Go to Appliance > Network > Interface.
2.Click the edit icon to configure each interface.
3.Set the IP address and netmask for the interface.
4.Click OK.
To configure the Primary and Secondary DNS server IP addresses
1.Go to Appliance > Network > DNS, enter the Primary and Secondary DNS IP address- es click Apply.
To configure a Default Gateway
1.Go to Appliance > Network > Static Routing and select Create New.
2.Set Gateway to the Default Gateway IP address and click OK.
Command Line Interface
The unit has serial port. Use the null modem cable to connect it to your management com- puter.
To connect to the unit
1.Use a null modem cable to connect the serial port to the management computer serial port.
2.Start a terminal emulation program (such as HyperTerminal) on the management com- puter. Use these settings: Baud Rate 9600, Data bits 8, Parity None, Stop bits 1, Flow Control None.
3.At the login prompt, type admin for the user name and fortidb1!$ for the password and press Enter.
After connecting to the CLI, you can configure the unit IP address, DNS server IP address, and default gateway to connect the unit to the network.
To configure the unit using the CLI
1.Set the IP address and netmask of the Port1 interface. config system interface
edit port1
set ip <intf_ip>/<netmask_ip>
set allowaccess ping https ssh http
next
edit port2 next edit port3 next edit port4 next
end
3.Configure the primary and secondary DNS server IP addresses. config system dns
set primary
end
4.Configure the default gateway. config system route
edit 1
set device <interface> set dst <destination_ip> set gateway <gateway_ip>
end
Shutting down the unit using the CLI
Enter the following command at the prompt:
execute shutdown
Visit these links for more information and documentation for your Fortinet product.
Technical Documentation - http://docs.forticare.com
Fortinet Knowledge Center - http://kb.fortinet.com
Fortinet Technical Support - http://support.fortinet.com
Training Services - http://campus.training.fortinet.com