Fortinet 310B manual Adding firewall policies, To modify the default gateway Go to Router Static

Page 22

Configuring NAT mode

Configuring

For an initial configuration, you must edit the factory configured static default route to specify a different default gateway for the FortiGate unit. This will enable the flow of data through the FortiGate unit.

For details on adding additional static routes, see the FortiGate Administration Guide.

To modify the default gateway

1Go to Router > Static.

2Select Edit for the default route

3In the Gateway field, type the IP address of the next-hop router where outbound traffic is directed.

4If the FortiGate unit reaches the next-hop router through a different interface (compared to the interface that is currently selected in the Device field), select the name of the interface from the Device field.

5Select OK.

Adding firewall policies

Firewall policies enable traffic to flow through the FortiGate interfaces. Firewall policies define how the FortiGate unit processes the packets in a communication session. You can configure the firewall policies to allow only specific traffic, users and specific times when traffic is allowed.

For the initial installation, a single firewall policy that enables all traffic through will enable you to verify your configuration is working. On lower-end units such a default firewall policy is already in place. For the higher end FortiGate units, you will need to add a firewall policy.

The following steps add two policies that allows all traffic through the FortiGate unit, to enable you to continue testing the configuration on the network.

To add an outgoing traffic firewall policy

1Go to Firewall > Policy.

2Select Create New.

3Set the following and select OK.

Source Interface

Select the port connected to the network.

Source Address

All

Destination Interface Select the port connected to the Internet.

Destination Address All

Schedulealways

ServiceAny

ActionAccept

To add an incoming traffic firewall policy

1Go to Firewall > Policy.

2Select Create New.

 

FortiGate-310B FortiOS 3.0 MR6 Install Guide

22

01-30006-0472-20080815

Image 22
Contents Install G U I D E Trademarks Regulatory complianceContents Protection profiles Firewall policies Configuring Transparent modeDownloading firmware Installing firmware from a system reboot using the CLI Using the web-based managerUsing the CLI Testing new firmware before installingPage Introduction Register your FortiGate unitAbout the FortiGate-310B Lacp configurationAbout this document Typographic conventions Further ReadingDocument conventions Addressipv4FortiGate Administration Guide Fortinet Knowledge CenterCustomer service and technical support Comments on Fortinet technical documentationCustomer service and technical support Installing Environmental specificationsRack mount instructions GroundingMounting To install the FortiGate unit into a rack Installed mounting bracketsTo power off the FortiGate unit Connecting to the networkTo power on the FortiGate unit Plugging in the FortiGateNAT vs. Transparent mode ConfiguringNAT mode Connecting to the web-based manager Connecting to the FortiGate unitTransparent mode To connect to the web-based managerBits per second 9600 Data bits Parity Connecting to the CLITo connect to the CLI Stop bits Flow controlConfigure the interfaces Configuring NAT modeUsing the web-based manager To configure interfaces Go to System Network InterfaceAdding a default route and gateway Configure a DNS serverInitial Padt Timeout Source Interface To modify the default gateway Go to Router StaticAdding firewall policies Source Address AllTo set an interface to use a static address Using the CLITo set an interface to use Dhcp addressing To configure DNS server settings To set an interface to use PPPoE addressingTo modify the default gateway To add an outgoing traffic firewall policySwitching to Transparent mode Configuring Transparent modeTo switch to Transparent mode Go to System Status Source Address All Destination Interface To switch to Transparent mode Verify the configuration Backing up the configurationSet the Administrator password Restoring a configurationAdditional configuration Set the time and dateConfigure FortiGuard Updating antivirus and IPS signaturesAdditional configuration Default protection profiles Advanced configurationProtection profiles Firewall policies Firewall policiesConfiguring firewall policies Antivirus optionsAntiSpam options Web filtering Logging To install the filler module Installing AMC filler unitsInstalling modules AMC modulesHard disk module Using the AMC modulesRemoving modules To insert a module into a FortiGate chassisFormatting the hard disk Log configuration using the web-based managerTo format the ASM-S08 hard disk enter the following command Execute formatlogdiskViewing logs Log configuration using the CLIChanging interfaces to operate in Sgmii or SerDes mode ASM-FB4 and ADM-XB2 modulesConfigure the speed Config system interface edit AMC-SW1/1 Set speed auto EndUsing the AMC modules FortiGate Firmware Downloading firmwareUpgrading the firmware Using the web-based managerReverting to a previous version Using the USB Auto-Install Backup and Restore from a USB keyTo revert to a previous firmware version To upgrade the firmware using the CLI Using the CLIExecute ping Execute update-now Execute restore image namestr tftpip4Execute restore image image.out To revert to a previous firmware version using the CLIExecute restore image image28.out Installing firmware from a system reboot using the CLIExecute restore image namestr tftpipv4 Execute restore config namestr tftpip4Press any key to display configuration menu To install firmware from a system rebootExecute reboot Enter Tftp server addressEnter Local Address Restoring the previous configurationTo backup configuration using the CLI Enter File Name image.outTo restore configuration using the CLI Additional CLI Commands for a USB keyTo configure the USB Auto-Install using the CLI Testing new firmware before installing To test the new firmware imageTesting new firmware before installing Testing new firmware before installing Index Web filtering 37 web-based manager Page Page

310B specifications

The Fortinet 310B is a powerful next-generation firewall (NGFW) designed to meet the evolving needs of modern enterprises. As part of Fortinet's Security Fabric, the 310B offers robust security features combined with high performance, enhancing network security while maintaining ease of use.

One of the standout features of the Fortinet 310B is its high throughput capability. With up to 10 Gbps of firewall throughput and an impressive IPS throughput of 3.5 Gbps, the device is optimized for handling heavy network traffic with minimal latency. This makes it suitable for both medium and large-scale environments, where performance and speed are critical.

The Fortinet 310B integrates a comprehensive suite of security technologies. At its core is FortiOS, the operating system that powers Fortinet’s security appliances. FortiOS includes advanced threat protection capabilities such as intrusion prevention system (IPS), deep packet inspection, and antivirus scanning. These features help protect against a wide range of threats, including malware, ransomware, and zero-day attacks, ensuring that networks are resilient against various cyber threats.

Another key characteristic of the Fortinet 310B is its multi-layered security architecture. The device supports a range of technologies such as SSL inspection, web filtering, and application control. By leveraging these functionalities, organizations can enforce granular security policies across different applications and users, improving overall visibility and control over the network environment.

The Fortinet 310B also incorporates FortiGate's unique Security Fabric technology, which enables seamless integration with other Fortinet products and third-party solutions. This interoperability allows for centralized management, simplified security operations, and enhanced threat intelligence sharing, creating a holistic security approach.

In addition to its security capabilities, the Fortinet 310B offers a variety of connectivity options, including multiple Ethernet ports and support for FortiLink, which allows for easy integration with FortiAP access points and FortiSwitches. This flexibility facilitates the deployment of secure network segments and wireless solutions.

The device also supports advanced features such as VPN capabilities for secure remote access, SD-WAN for optimizing network performance, and extensive reporting and logging for compliance and accountability. All these attributes make the Fortinet 310B a formidable choice for organizations looking to bolster their network security posture while maximizing operational efficiency. Overall, the Fortinet 310B stands out as a reliable and versatile solution in the realm of network security appliances.