Uniden EXAI 7248 owner manual Mount the Base Unit on a Wall, Standard wall plate mounting

Page 9

D. Mount the Base Unit on a Wall

Standard wall plate mounting

This phone can be mounted on any standard wall plate.

1) Locate the base unit on the wall mount adapter as shown and slide the wall mount adapter into the notches on the base bottom.

2)

Plug the AC adapter to the DC IN 9V

2

 

jack.

3)

Route the AC adapter cord through

 

 

the molded wiring channel as shown.

7

4)

Plug the AC adapter into a standard

6

 

120V AC wall outlet.

7

5)

Plug the telephone line cord into the

 

 

TEL LINE jack. Route the cord

3

 

through the molded wiring channel

 

 

 

as shown.

4

 

 

6) Plug the telephone line cord into the telephone outlet.

7)Align the mounting slots on the base with the mounting posts on the wall. Then push in and down until the phone is firmly seated.

1

5

To remove, push up a tab on the wall mount adapter as shown.

G E T T I N G S T A R T E D

w w w . u n i d e n . c o m

G E T T I N G S T A R T E D [ 8 ]

Image 9
Contents Series Owners Manual Contents Itad Welcome FeaturesRetrieve TAD message with Handset Remote keys Controls and FunctionsN T R O L S & F U N C T I O N S Terms Used in this ManualInstalling the Phone Choose the Best LocationDo the following steps Install the Rechargeable Battery Pack into the Handset Use only the supplied Connect the Base Unit and Charge the HandsetStandard wall plate mounting Mount the Base Unit on a WallDirect wall mounting Installing the BeltclipHeadset Installation Basic Setup Activating AutoTalkActivating Caller ID on Call Waiting Entering Your Area Code Setting the Language Choosing the Dialing ModeSelecting the Ring Tone and Volume Making and Receiving Calls Using Your PhoneMaking a call Receiving a callAdjusting the Earpiece Volume Redialing the last dialed numberTemporarily Mute Ringer Tone Dialing Switch-over Traveling Out-of-RangeSelecting a Different Channel Find Handset Using Call WaitingStoring the RocketDial RocketDialStoring Names and Numbers in Speed Dial Memory Using the Speed Dial MemoryIf you make a mistake while entering a name I N G T H E S P E E D D I a L M E M O R Y Storing Caller ID messages in Speed Memory Locations Making Calls from Speed Dial Memory To cancel speed dialingCaller ID and Cidcw Caller ID on Call Waiting When the Telephone RingsL L E R I D F E a T U R E S 2 Viewing the Caller ID Message ListDeleting Information from the Caller ID List Deleting a Caller ID MessageDeleting all Caller ID names/numbers Making a Call from the Caller ID List Integrated Answering Device FeaturesTurning the Answering System On/Off Answering System Settings Setting Up Your Answering SystemSetting the Time Setting a Personal Security Code PIN Setting the Ring Time Selecting the Message Record Time Announce only featureSetting the Message Alert Tone Setting Your Outgoing Message Greeting Preset messageSelecting the Language Choosing between the two outgoing messages Recording a personal outgoing message GreetingSetting the Base Ringer Volume Adjusting the Speaker Volume LevelTemporarily Mute the Base Ringer and Call Screen Playing Your Messages Using Your Answering SystemRepeating a Message Reviewing Messages using HandsetSkipping a Message Deleting a Message Recording a Conversation Voice MemoRemote Operation Remote Access away from HomeFunction Turn on the Answering System Remotely Remote Access with the Handset H E I N T E G R a T E D a N S W E R I N G D E V I C E Changing the Digital Security Code Battery replacement and handling Low battery alertCleaning the battery charging contacts Frequency General InformationSymptom Suggestion TroubleshootingAppliances D I T I O N a L I N F O R M a T I O N Additional Information Case Action Liquid DamagePrecautions Installation Considerations Terminal Equipment Radio Equipment G, H, I, J, K, L IndexMemo Memo Remote Operation Card Memory Location Memo Remote Operation CardTask Key Please do not Return this Product to the Place of Purchase Register Online Today