Enterasys Networks BL-6000ENT manual Hardware Specifications, Regulatory Compliance Standards

Page 27

Hardware Specifications

A

Hardware Specifications

Regulatory Compliance Standards

This equipment meets the following safety and electromagnetic compatibility (EMC) requirements:

Safety	UL 60950, CSA C22.2 No. 60950, 73/23/EEC, EN 60950,
	IEC 60950

Electromagnetic Compatibility	47 CFR Parts 2 and 15, CSA C108.8, 89/336/EEC, EN 55022,
(EMC)	EN 61000-3-2, EN 61000-3-3, EN 55024, AS/NZS CISPR 22,
	VCCI V-3

Product Standards

This equipment meets the following product standards:

Standards	IEEE 802.3af

Specifications

Model BL-69108ENT

•8 female RJ45 data input ports

•Shielded jacks for Category 5 or greater UTP (two pair wire) or 100‐ohm STP (two pair wire)

•Distance: Up to 100 meters, standard Ethernet distance

•8 female RJ45 Data+Power on Ethernet (Power over Ethernet) output ports

Mid-Span Power Hub User’s Guide A-1

Image 27

Contents Mid-Span Power Hub 8-Port and 24-Port User’s Guide7.5x9-inch cover with bleed on 4 sides Page Enterasys Networks, Inc 50 Minuteman Road Andover, MA Industry Canada Notice Product SafetyRegulatory Compliance Information Federal Communications Commission FCC NoticeEuropean Waste Electrical and Electronic Equipment WEEE Notice Electromagnetic Compatibility EMCCompatibilidad Electromágnetica EMC Elektro- magnetische Kompatibilität EMCBSMI EMC Statement - Taiwan VCCI NoticeAndover, MA USA ONE-YEAR LIMITED WARRANTYDeclaration of Conformity Manufacturer’s Name Enterasys Networks, IncYou and Enterasys agree as follows Enterasys Networks, Inc Firmware License AgreementBEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT CAREFULLY READ THIS LICENSE AGREEMENT3. APPLICABLE LAW. This Agreement shall be interpreted and governed under the laws and in the state and 9. OWNERSHIP. This is a license agreement and not an agreement for sale. You acknowledge and agree that the Program constitutes trade secrets and/or copyrighted material of Enterasys and/or its suppliers. You agree to implement reasonable security measures to protect such trade secrets and copyrighted material. All right, title and interest in and to the Program shall remain with Enterasys and/or its suppliers. All rights not specifically granted to You shall be reserved to Enterasys Appendix A Hardware Specifications ContentsChapter 2 Installation and Connection Chapter 3 TroubleshootingPage About This Guide PurposeWho Should Use This Guide The following conventions are used in this guide Document ConventionsGetting Help Your Enterasys Networks service contract numberNetwork load and frame size at the time of trouble if known xiv About This Guide Functions and Features Port IndicatorsIntroduction 1-2 Introduction Port IndicatorsVerifying the Kit Installation and ConnectionPower Cord Kit ContentsFigure 2-1 Contents of the BL-69108ENT Kit Figure 2-2 Contents of the BL-69524ENT KitTechnical Considerations Configuration for a Mid-Span Power HubFigure 2-3 Typical Configuration for a Mid-Span Power Hub Powering Upfrom Ethernet switch Figure 2-4 Module Bank for the 8-Port and 24-Port Mid-Span Power HubsPower / Data Out to device to be powered Detect / Power Forwarding Blue Power Green Data In2-6 Installation and Connection Recommended Action TroubleshootingTable 3-1 Troubleshooting Checklist ProblemTable 3-1 Troubleshooting Checklist continued Product Standards Hardware SpecificationsSpecifications Regulatory Compliance StandardsModel BL-69524ENT Physical/Mechanical SpecificationsLED Indicators/Module Table A-1 Physical and Mechanical SpecificationsAC Power Input Physical/Environmental SpecificationsElectrical Specifications Table A-3 Physical and Environmental SpecificationsSpecifications