Enterasys Networks BL-6000ENT manual Regulatory Compliance Information, Industry Canada Notice

Page 4

Regulatory Compliance Information

Federal Communications Commission (FCC) Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not installed in accordance with the operator’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense.

WARNING: Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Industry Canada Notice

This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

Class A ITE Notice

WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Clase A. Aviso de ITE

ADVERTENCIA: Este es un producto de Clase A. En un ambiente doméstico este producto puede causar interferencia de radio en cuyo caso puede ser requerido tomar medidas adecuadas.

Klasse A ITE Anmerkung

WARNHINWEIS: Dieses Produkt zählt zur Klasse A ( Industriebereich ). In Wohnbereichen kann es hierdurch zu Funkstörungen kommen, daher sollten angemessene Vorkehrungen zum Schutz getroffen werden.

Product Safety

This product complies with the following: UL 60950, CSA C22.2 No. 60950, 73/23/EEC, EN 60950, IEC 60950.

Seguridad del Producto

El producto de Enterasys cumple con lo siguiente: UL 60950, CSA C22.2 No. 60950, 73/23/EEC, EN 60950.

Produktsicherheit

Dieses Produkt entspricht den folgenden Richtlinien: UL 60950, CSA C22.2 No. 60950, 73/23/EEC, EN 60950.

ii

Image 4
Contents User’s Guide Mid-Span Power Hub 8-Port and 24-Port7.5x9-inch cover with bleed on 4 sides Page Enterasys Networks, Inc 50 Minuteman Road Andover, MA Product Safety Regulatory Compliance InformationFederal Communications Commission FCC Notice Industry Canada NoticeElectromagnetic Compatibility EMC Compatibilidad Electromágnetica EMCElektro- magnetische Kompatibilität EMC European Waste Electrical and Electronic Equipment WEEE NoticeVCCI Notice BSMI EMC Statement - TaiwanONE-YEAR LIMITED WARRANTY Declaration of ConformityManufacturer’s Name Enterasys Networks, Inc Andover, MA USAEnterasys Networks, Inc Firmware License Agreement BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCTCAREFULLY READ THIS LICENSE AGREEMENT You and Enterasys agree as follows3. APPLICABLE LAW. This Agreement shall be interpreted and governed under the laws and in the state and 9. OWNERSHIP. This is a license agreement and not an agreement for sale. You acknowledge and agree that the Program constitutes trade secrets and/or copyrighted material of Enterasys and/or its suppliers. You agree to implement reasonable security measures to protect such trade secrets and copyrighted material. All right, title and interest in and to the Program shall remain with Enterasys and/or its suppliers. All rights not specifically granted to You shall be reserved to Enterasys Contents Chapter 2 Installation and ConnectionChapter 3 Troubleshooting Appendix A Hardware SpecificationsPage Purpose About This GuideWho Should Use This Guide Document Conventions Getting HelpYour Enterasys Networks service contract number The following conventions are used in this guideNetwork load and frame size at the time of trouble if known xiv About This Guide Port Indicators Functions and FeaturesIntroduction Port Indicators 1-2 IntroductionInstallation and Connection Verifying the KitKit Contents Figure 2-1 Contents of the BL-69108ENT KitFigure 2-2 Contents of the BL-69524ENT Kit Power CordConfiguration for a Mid-Span Power Hub Technical ConsiderationsPowering Up Figure 2-3 Typical Configuration for a Mid-Span Power HubFigure 2-4 Module Bank for the 8-Port and 24-Port Mid-Span Power Hubs Power / Data Out to device to be poweredDetect / Power Forwarding Blue Power Green Data In from Ethernet switch2-6 Installation and Connection Troubleshooting Table 3-1 Troubleshooting ChecklistProblem Recommended ActionTable 3-1 Troubleshooting Checklist continued Hardware Specifications SpecificationsRegulatory Compliance Standards Product StandardsPhysical/Mechanical Specifications LED Indicators/ModuleTable A-1 Physical and Mechanical Specifications Model BL-69524ENTPhysical/Environmental Specifications Electrical SpecificationsTable A-3 Physical and Environmental Specifications AC Power InputSpecifications