deXlan 050862 user manual Appendix a Router Configuration, Port Forwarding for IP Camera

Page 70

Appendix A: Router Configuration

Appendix A: Router Configuration

The following section describes the initial configuration of the router and port forwarding for your router. If your router is not listed here, please refer to the manufacturer’s website for assistance with configuring your router to work with IP Camera.

Port Forwarding for IP Camera

IP Camera requires certain ports to be open on your router to allow other computers on the Internet to “see” it on your internal network. Normally, your router will have the less common ports disabled or blocked by the router’s built-in firewall. In order for the IP Camera applications to work properly and not be blocked, the firewall settings need to be configured. In each instance there will be a trigger port and incoming port(s), where traffic on the trigger port tells the Firewall to open the incoming ports. The IP Camera require that TCP Port 80 and UDP 9001 (default settings) be opened to the Internet. TCP Port 80 is used for accessing the camera’s homepage and UDP Port 9001 is used for authentication and video streaming.

If your Internet service Provider blocks port 80/9001, you’ll need to reconfigure your camera and router to other ports such as 81/9002, 82/9003, etc. To change the port settings on the camera, you’ll need to use Utility.

Follow the steps below to configure your router, depending on the router manufacturer and model. If your particular router manufacturer or model is not listed below, please contact your router manufacturer for further assistance in configuring the router.

The Following Router manufacturers and models are included in this document:

Brand

Model

 

Description

 

 

3Com

3C857-US

 

OfficeConnect Cable/DSL Gateway

 

3CRWE52196

OfficeConnect

Wireless

Cable/DSL

 

 

 

Gateway

 

 

Belkin

F5D6230-3

 

Wireless Cable/DSL Gateway Router

 

F5D7230-4– 54g

Wireless DSL/Cable gateway Router

D-Link

DI-604/DI–614+/DI-624

-

 

 

 

DI-704/704P

-

 

 

 

DI714

 

-

 

 

 

DI-714P+

 

-

 

 

Dell

TrueMobile

2300

-

 

 

 

Wireless

Broadband

 

 

 

 

Router

 

 

 

 

Linksys

BEFSR41

 

EtherFast Cable/DSL Router

 

 

BEFSX41

 

Instant Broadband EtherFast

Cable/DSL

 

 

 

Firewall Router with 4-Port Switch/VPN

 

 

 

EndPoint

 

 

 

BEFW11S4

 

Wireless Access Point Router with 4-Port

 

 

 

Switch – Version 2

 

 

Microsoft

MN-100

 

Wired Base Station

 

 

iCAMView user manual

-67-

Image 70
Contents IP Camera Contents Device View System User Help Drag-and-Drop Feature Features IntroductionPackage Contents IP Camera Back View Installation Procedure IP Camera installation flowchartInstallation Procedure IP Camera, USB Camera and the NetworkICAMView, USB Camera and the Network Using Utility to Setup IP & Update Firmware Installing UtilityUsing Utility Setup Wizard Using Utility to Setup IP & Update Firmware Using Utility to Setup IP & Update Firmware Using Utility to Setup IP & Update Firmware Using Utility to Setup IP & Update Firmware Launch IP Camera IP Configuration IPAddress AdvancedDevice Password IP Configuration IP Camera Advanced settingsIi. Management Protocol For exampleAbout RefreshIP Camera Web Manager IntroductionIP Camera Web Manager Interface Web-Camera Selection System Status InformationSystem Information Current Connections Ii. System InformationBasic Settings Event LogCamera Settings Network Account Settings Camera SettingsSetting up Camera a Similar with Camera B IP Address NetworkIi. DNS Server IP Iv. Ethernet Iii. Port NumberDynamic DNS Vi. PPPoE Account SettingsUser Account User Name An Administrator has full access including write Advanced Settings Event NotificationEvent Notification Send Email IP Camera Event NotificationIP Camera Event Selection List Samples Camera a or Camera B Enable Motion DetectionIP Camera Motion Detection IP Camera Motion Detect Email Notification Image Recording Camera a or Camera B Begin End hhmmMail / FTP IP Camera Email of Image RecordedFTP Settings FTP Server Ii. Email Settings E-mail ServerIii. Sending Test Mail IP Camera test mail functionSystem Settings Iv. Email Address BookIv. Snmp Settings Iii. LED SettingsIi. System Restart Image Server Language Ii. Email Preference Ii. Save / Restore Settings Save current ConfigurationInterface Language AboutViewing images using PDA / Web enabled mobile phone IP Camera AboutAccessing IP Camera via PDA Installing MultiMonitor MultiMonitorMultiMonitor MultiMonitor Device MultiMonitor Display the current Camera settings Display the Motion Detection Settings REDImage Recording Configure Settings for Email Notification Avifilethree digit numerical sequenceSnmp Settings Server Require AuthenticationNotified Email Address Using Snmp to update network ports MultiMonitor MultiMonitor View SystemUser Help Drag-and-Drop Feature StepDouble click on the icon on the desktop, to view the images Appendix a Router Configuration Port Forwarding for IP CameraSMC SMC2404WBR Appendix a Router Configuration TCP UDP TCP Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP TCP Appendix a Router Configuration TCP Appendix a Router Configuration Gateways Appendix B IP Address, Subnet and GatewayCommunities IP AddressesSubnetting and Subnet Masks Subnet Mask Routing and FilteringAppendix C Glossary Term Definition