Edimax Technology Multi-Homing Broadband Router manual

Page 87

create IP address numbers used only within a particular network (as opposed to valid IP address numbers recognized by the Internet, which must be assigned by InterNIC).

TCP/IP, UDP: Transmission Control Protocol/Internet Protocol (TCP/IP) and Unreliable Datagram Protocol (UDP). TCP/IP is the standard protocol for data transmission over the Internet. Both TCP and UDP are transport layer protocol. TCP performs proper error detection and error recovery, and thus is reliable. UDP on the other hand is not reliable. They both run on top of the IP (Internet Protocol), a network layer protocol.

WAN: Wide Area Network. A network that connects computers located in geographically separate areas (e.g. different buildings, cities, countries). The Internet is a wide area network.

Web-based management Graphical User Interface (GUI): Many devices support a graphical user interface that is based on the web browser. This means the user can use the familiar Netscape or Microsoft Internet Explorer to Control/configure or monitor the device being managed.

87

Image 87

Contents User Manual Multi-Homing Broadband Router2.4.3 Special Applications FeaturesSetup Diagram Step 2 Broadband Type4.2 Firmware Upgrade 2.5.1 Access Control2.5.3 DoS Denial of Service Configuration ToolsMinimum Requirements FeaturesPackage Content Introduction2 Wide Area Network WAN Get to know the Broadband Router Back Panel3 Reset 1 Local Area Network LANFront Panel Figure 1.2 below shows a typical setup for a Local Area Network LAN Setup DiagramWINS Configuration Select Disable WINS Resolution Getting startedConfigure your PC to obtain an IP address automatically DNS Configuration Select Disable DNS3 In the Local Area Connection window, click the Properties button 2b Windows2c Windows NT IP Address Select Obtain an IP address from a DHCP server Quick Setup Wizard Chapter General Setup ChapterStatus Information Chapter Tools Chapter Quick Setup Wizard ChapterGeneral Setup Chapter Status Information ChapterLogout Tools ChapterStep 1 Time Zone Quick SetupEnable Daylight Savings ChapterDescription End Daylight Savings TimeStep 2 Broadband Type Menu1.4 Telstra Big Pond 1.3 PPPoE1.4 PPTP 1.5 L2TPIf your ISP requires a Host Name, type in the host name This is the IP address that your ISP has given you THE ROUTER WHEN YOU FINISHED USING THE INTERNET 1.4 PPTP Password Click OK when you have finished the configuration above. Congratulations! You have completed the configuration for the PPTP connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3 IP Address 1.6 Telstra Big Pond server manually Login ServerThe IP of the Login Server manuallyGeneral Settings 2.4 NAT 2.1 System2.2 WAN 2.3 LAN2.1.1 Time Zone System SettingsEnd Daylight Savings Time 2.1.2 Password Settings2.1.3 Remote Management Confirmed PasswordHost Address 2.2.3 PPPoE 2.2 WAN2.2.1 Dynamic IP address 2.2.2 Static IP address2.2.1 Dynamic IP 2.2.8 QoS2.2.9 DNS 2.2.10 DDNSParameter Gateway Description 2.2.7 WAN Policy The QoS can let you classify Internet application traffic by source/destination IP, MAC address and port number. You can assign priority for each type of application and reserve bandwidth for it. The packets of applications with higher priority will always go first. Lower priority applications will get bandwidth after higher priority applications get enough bandwidth. This can let you have a better experience in using critical real time services like Internet phone, video conference …etc. All the applications not specified by you are classified as rule name “Others”. The rule with smaller priority number has higher priority the rule with larger priority number has lower priority. You can adjust the priority of the rules by moving them up or down Enable/Disable QoS Add a QoS rule into the table Select the WAN ports that the packets matching QoS Rulerule and click “Move Down” to make its priority lower The name of this ruleSource IP Address BandwidthSource Address Source MAC AddressApply ResetDefault Domain Name Server DNS addressSecondary DNS Address optional DynDNS Enable/DisablePassword/Key ProviderLAN IP 2.3 LAN192.168.2.100 to End IP 192.168.2.199 . If you IP Address PoolLease Time Domain Name2.4 NAT 2.4.1 Port Forwarding settings from the Current Port Forwarding The description of this setting“WAN Port” and Comment of the setting to be Forwarding setting will be added into the2.4.2 Virtual Server Public Port Example Virtual Server 2.4.3 Special Applications Example Example Special ApplicationsUPnP Feature 2.4.4 UPnPParametersDescription 2.4.5 Protocol and Port BindingAdd a Rule 2.4.7 Static Routing 2.4.6 ALG Settings“Default Gateway”, Hop Count and Interface of Enable Static RoutingStatic Routing function is default disabled. You have to enable the Static Routing function beforerule of Static Routing will be added into the Static 2.5 Firewall If you want to restrict users from accessing certain Internet applications/servicese.g. Internet websites, email, FTP etc., then this is the place to set that configuration. Access Control allows users to define the traffic type permitted in your LAN. You can control which PC client can have access to these services Filter client PCs by IPAdd PC Client PC IP Address Example Access Control 2.5.2 URL Blocking 2.5.3 DoS Denial of Service Discard Ping From WAN Intrusion Detection FeaturePing of Death packets occurredNote DMZ function works only when the NAT function is enabled Client PC IP Address 3.1 Status and Information Shows the router’s system information 3.1 Status and Information Hardware version, Boot code Version, Runtime code VersionYou can see the router’s system information such as the router’s the Primary DNS and Secondary DNS being used 3.2 Internet ConnectionServer 3.3 Device StatusThis page shows the current system log of the Broadband router 3.5 Security Log connected to your network. The “Active DHCP Client Table” 3.6 Active DHCP Clientupdated situation This page shows all DHCP clients LAN PCs currentlyShows the counters of packets sent and received on WAN and 3.7 StatisticsYou can reset the router’s system should any problem exist 4.1 Configuration Tools This page allows you to upgrade the router’s firmware 4.3 ResetOnce the reset process is complete you may start using the some way stops functioning, you can perform a reset. Yoursettings will not be changed. To perform the reset, click on the The reset will be complete when the power light stops blinkingAppendix A How to Manually find your PC’s IP and MAC addressGlossary SMTP ApplicationPort Number Telnet