Edimax Technology Multi-Homing Broadband Router manual 2c Windows NT

Page 10

2c) Windows NT

6:Click OK to confirm the setting. Your PC will now obtain an IP address automatically from your Broadband Router’s DHCP server.

Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your LAN.

Once you’ve configured your PC to obtain an IP address automatically, please proceed to Step 3 (Page 11).

2c) Windows NT

1:Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear.

2:Double-click Network icon. The Network window will appear. Select the Protocol tab from the Network window.

3:Check if the TCP/IP Protocol is on your list of Network Protocols. If TCP/IP is not installed, click the Add button to install it now. If TCP/IP is installed, go to step 5.

4:In the Select Network Protocol window, select the TCP/IP Protocol and click the Ok button to start installing the TCP/IP protocol. You may need your Windows CD to complete the installation.

10

Image 10

Contents Multi-Homing Broadband Router User ManualStep 2 Broadband Type FeaturesSetup Diagram 2.4.3 Special ApplicationsConfiguration Tools 2.5.1 Access Control2.5.3 DoS Denial of Service 4.2 Firmware UpgradeIntroduction FeaturesPackage Content Minimum Requirements1 Local Area Network LAN Get to know the Broadband Router Back Panel3 Reset 2 Wide Area Network WANFront Panel Setup Diagram Figure 1.2 below shows a typical setup for a Local Area Network LANDNS Configuration Select Disable DNS Getting startedConfigure your PC to obtain an IP address automatically WINS Configuration Select Disable WINS Resolution2b Windows 3 In the Local Area Connection window, click the Properties button2c Windows NT IP Address Select Obtain an IP address from a DHCP server General Setup Chapter Quick Setup Wizard ChapterStatus Information Chapter Status Information Chapter Quick Setup Wizard ChapterGeneral Setup Chapter Tools ChapterTools Chapter LogoutChapter Quick SetupEnable Daylight Savings Step 1 Time ZoneMenu End Daylight Savings TimeStep 2 Broadband Type Description1.5 L2TP 1.3 PPPoE1.4 PPTP 1.4 Telstra Big PondIf your ISP requires a Host Name, type in the host name This is the IP address that your ISP has given you THE ROUTER WHEN YOU FINISHED USING THE INTERNET 1.4 PPTP Password Click OK when you have finished the configuration above. Congratulations! You have completed the configuration for the PPTP connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3 IP Address 1.6 Telstra Big Pond manually Login ServerThe IP of the Login Server server manuallyGeneral Settings 2.3 LAN 2.1 System2.2 WAN 2.4 NATSystem Settings 2.1.1 Time Zone2.1.2 Password Settings End Daylight Savings TimeConfirmed Password 2.1.3 Remote ManagementHost Address 2.2.2 Static IP address 2.2 WAN2.2.1 Dynamic IP address 2.2.3 PPPoE2.2.10 DDNS 2.2.8 QoS2.2.9 DNS 2.2.1 Dynamic IPParameter Gateway Parameter 2.2.7 WAN Policy The QoS can let you classify Internet application traffic by source/destination IP, MAC address and port number. You can assign priority for each type of application and reserve bandwidth for it. The packets of applications with higher priority will always go first. Lower priority applications will get bandwidth after higher priority applications get enough bandwidth. This can let you have a better experience in using critical real time services like Internet phone, video conference …etc. All the applications not specified by you are classified as rule name “Others”. The rule with smaller priority number has higher priority the rule with larger priority number has lower priority. You can adjust the priority of the rules by moving them up or down Enable/Disable QoS Add a QoS rule into the table The name of this rule QoS Rulerule and click “Move Down” to make its priority lower Select the WAN ports that the packets matchingSource MAC Address BandwidthSource Address Source IP AddressReset ApplyDomain Name Server DNS address DefaultSecondary DNS Address optional Provider Enable/DisablePassword/Key DynDNS2.3 LAN LAN IPDomain Name IP Address PoolLease Time 192.168.2.100 to End IP 192.168.2.199 . If you2.4 NAT 2.4.1 Port Forwarding Forwarding setting will be added into the The description of this setting“WAN Port” and Comment of the setting to be settings from the Current Port Forwarding2.4.2 Virtual Server Public Port Example Virtual Server 2.4.3 Special Applications Example Special Applications Example2.4.4 UPnP UPnP Feature2.4.5 Protocol and Port Binding ParametersDescriptionAdd a Rule 2.4.6 ALG Settings 2.4.7 Static Routinghave to enable the Static Routing function before Enable Static RoutingStatic Routing function is default disabled. You “Default Gateway”, Hop Count and Interface ofrule of Static Routing will be added into the Static 2.5 Firewall Filter client PCs by IP If you want to restrict users from accessing certain Internet applications/servicese.g. Internet websites, email, FTP etc., then this is the place to set that configuration. Access Control allows users to define the traffic type permitted in your LAN. You can control which PC client can have access to these servicesAdd PC Client PC IP Address Example Access Control 2.5.2 URL Blocking 2.5.3 DoS Denial of Service packets occurred Intrusion Detection FeaturePing of Death Discard Ping From WANNote DMZ function works only when the NAT function is enabled Client PC IP Address 3.1 Status and Information Shows the router’s system information Hardware version, Boot code Version, Runtime code Version 3.1 Status and InformationYou can see the router’s system information such as the router’s 3.2 Internet Connection the Primary DNS and Secondary DNS being used3.3 Device Status ServerThis page shows the current system log of the Broadband router 3.5 Security Log This page shows all DHCP clients LAN PCs currently 3.6 Active DHCP Clientupdated situation connected to your network. The “Active DHCP Client Table”3.7 Statistics Shows the counters of packets sent and received on WAN andYou can reset the router’s system should any problem exist 4.1 Configuration Tools 4.3 Reset This page allows you to upgrade the router’s firmwareThe reset will be complete when the power light stops blinking some way stops functioning, you can perform a reset. Yoursettings will not be changed. To perform the reset, click on the Once the reset process is complete you may start using theHow to Manually find your PC’s IP and MAC address Appendix AGlossary Telnet ApplicationPort Number SMTP