Edimax Technology Multi-Homing Broadband Router manual System Settings, Time Zone

Page 29

System Settings

Parameters	Description
System Settings
2.1.1 Time Zone	Select the time zone of the country you are currently in.
	The router will set its time based on your selection.
2.1.2 Password Settings	Allows you to select a password in order to access the
	web-based management website.
2.1.3 Remote Management	You can specify a Host IP address that can perform
	remote management functions.

Select one of the above three system settings selections and proceed to the manual’s relevant sub-section

2.1.1 Time Zone

The Time Zone allows your router to reference or base its time on the settings configured here, which will affect functions such as Log entries and Firewall settings.

Parameter	Description
Set Time Zone	Select the time zone of the country you are currently in.
	The router will set its time based on your selection.

	29

Image 29

Contents User Manual Multi-Homing Broadband RouterSetup Diagram FeaturesStep 2 Broadband Type 2.4.3 Special Applications2.5.3 DoS Denial of Service 2.5.1 Access ControlConfiguration Tools 4.2 Firmware UpgradePackage Content FeaturesIntroduction Minimum Requirements3 Reset Get to know the Broadband Router Back Panel1 Local Area Network LAN 2 Wide Area Network WANFront Panel Figure 1.2 below shows a typical setup for a Local Area Network LAN Setup DiagramConfigure your PC to obtain an IP address automatically Getting startedDNS Configuration Select Disable DNS WINS Configuration Select Disable WINS Resolution3 In the Local Area Connection window, click the Properties button 2b Windows2c Windows NT IP Address Select Obtain an IP address from a DHCP server Status Information Chapter Quick Setup Wizard ChapterGeneral Setup Chapter General Setup Chapter Quick Setup Wizard ChapterStatus Information Chapter Tools ChapterLogout Tools ChapterEnable Daylight Savings Quick SetupChapter Step 1 Time ZoneStep 2 Broadband Type End Daylight Savings TimeMenu Description1.4 PPTP 1.3 PPPoE1.5 L2TP 1.4 Telstra Big PondIf your ISP requires a Host Name, type in the host name This is the IP address that your ISP has given you THE ROUTER WHEN YOU FINISHED USING THE INTERNET 1.4 PPTP Password Click OK when you have finished the configuration above. Congratulations! You have completed the configuration for the PPTP connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3 IP Address 1.6 Telstra Big Pond The IP of the Login Server Login Servermanually server manuallyGeneral Settings 2.2 WAN 2.1 System2.3 LAN 2.4 NAT2.1.1 Time Zone System SettingsEnd Daylight Savings Time 2.1.2 Password Settings2.1.3 Remote Management Confirmed PasswordHost Address 2.2.1 Dynamic IP address 2.2 WAN2.2.2 Static IP address 2.2.3 PPPoE2.2.9 DNS 2.2.8 QoS2.2.10 DDNS 2.2.1 Dynamic IPParameter Gateway 2.2.6 Telstra Big Pond 2.2.7 WAN Policy The QoS can let you classify Internet application traffic by source/destination IP, MAC address and port number. You can assign priority for each type of application and reserve bandwidth for it. The packets of applications with higher priority will always go first. Lower priority applications will get bandwidth after higher priority applications get enough bandwidth. This can let you have a better experience in using critical real time services like Internet phone, video conference …etc. All the applications not specified by you are classified as rule name “Others”. The rule with smaller priority number has higher priority the rule with larger priority number has lower priority. You can adjust the priority of the rules by moving them up or down Enable/Disable QoS Add a QoS rule into the table rule and click “Move Down” to make its priority lower QoS RuleThe name of this rule Select the WAN ports that the packets matchingSource Address BandwidthSource MAC Address Source IP AddressApply ResetSecondary DNS Address optional DefaultDomain Name Server DNS address Password/Key Enable/DisableProvider DynDNSLAN IP 2.3 LANLease Time IP Address PoolDomain Name 192.168.2.100 to End IP 192.168.2.199 . If you2.4 NAT 2.4.1 Port Forwarding “WAN Port” and Comment of the setting to be The description of this settingForwarding setting will be added into the settings from the Current Port Forwarding2.4.2 Virtual Server Public Port Example Virtual Server 2.4.3 Special Applications Example Example Special ApplicationsUPnP Feature 2.4.4 UPnPParametersDescription 2.4.5 Protocol and Port BindingAdd a Rule 2.4.7 Static Routing 2.4.6 ALG SettingsStatic Routing function is default disabled. You Enable Static Routinghave to enable the Static Routing function before “Default Gateway”, Hop Count and Interface ofrule of Static Routing will be added into the Static 2.5 Firewall If you want to restrict users from accessing certain Internet applications/servicese.g. Internet websites, email, FTP etc., then this is the place to set that configuration. Access Control allows users to define the traffic type permitted in your LAN. You can control which PC client can have access to these services Filter client PCs by IPAdd PC Client PC IP Address Example Access Control 2.5.2 URL Blocking 2.5.3 DoS Denial of Service Ping of Death Intrusion Detection Featurepackets occurred Discard Ping From WANNote DMZ function works only when the NAT function is enabled Client PC IP Address 3.1 Status and Information Shows the router’s system information You can see the router’s system information such as the router’s 3.1 Status and InformationHardware version, Boot code Version, Runtime code Version the Primary DNS and Secondary DNS being used 3.2 Internet ConnectionServer 3.3 Device StatusThis page shows the current system log of the Broadband router 3.5 Security Log updated situation 3.6 Active DHCP ClientThis page shows all DHCP clients LAN PCs currently connected to your network. The “Active DHCP Client Table”Shows the counters of packets sent and received on WAN and 3.7 StatisticsYou can reset the router’s system should any problem exist 4.1 Configuration Tools This page allows you to upgrade the router’s firmware 4.3 Resetsettings will not be changed. To perform the reset, click on the some way stops functioning, you can perform a reset. YourThe reset will be complete when the power light stops blinking Once the reset process is complete you may start using theAppendix A How to Manually find your PC’s IP and MAC addressGlossary Port Number ApplicationTelnet SMTP