STK15C88
Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the device. These user guidelines are not tested.
Storage Temperature | |
Temperature under bias | |
Supply Voltage on VCC Relative to GND | |
Voltage on Input Relative to Vss |
Voltage on | |
Power Dissipation | 1.0W |
DC output Current (1 output at a time, 1s duration) .... 15 mA
Operating Range
Range | Ambient Temperature | VCC |
Commercial | 0°C to +70°C | 4.5V to 5.5V |
|
|
|
Industrial | 4.5V to 5.5V | |
|
|
|
DC Electrical Characteristics
Over the operating range (VCC = 4.5V to 5.5V)
Parameter | Description |
|
|
|
|
| Test Conditions |
|
| Min | Max | Unit | |||||
ICC1 | Average VCC Current | tRC = 25 ns | Commercial |
| 97 | mA | |||||||||||
|
|
| tRC = 45 ns |
|
|
| 70 | mA | |||||||||
|
|
| Dependent on output loading and cycle rate. Values |
|
|
|
| ||||||||||
|
|
| Industrial |
| 100 | mA | |||||||||||
|
|
| obtained without output loads. |
|
|
| 70 | mA | |||||||||
|
|
| IOUT = 0 mA. |
|
|
| |||||||||||
|
|
|
|
|
|
|
| ||||||||||
ICC2 | Average VCC Current |
| All Inputs Do Not Care, VCC = Max |
|
|
| 3 | mA | |||||||||
| during STORE |
| Average current for duration tSTORE |
|
|
|
|
| |||||||||
ICC3 | Average VCC Current |
|
|
| > (VCC – 0.2V). All other inputs cycling. |
|
|
| 10 | mA | |||||||
WE |
|
|
| ||||||||||||||
| at tRC= 200 ns, 5V, |
| Dependent on output loading and cycle rate. Values obtained |
|
|
| |||||||||||
| 25°C Typical |
| without output loads. |
|
|
|
|
| |||||||||
ICC4 | Average Current |
| All Inputs Do Not Care, VCC = Max |
|
|
| 2 | mA | |||||||||
| during AutoStore |
| Average current for duration tSTORE |
|
|
|
|
| |||||||||
| Cycle |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ISB1[3] | Average VCC Current |
| tRC=25ns, |
| > VIH | Commercial |
| 30 | mA | ||||||||
CE |
| ||||||||||||||||
| (Standby, Cycling |
| tRC=45ns, CE > VIH |
|
|
| 22 |
| |||||||||
| TTL Input Levels) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Industrial |
| 31 | mA | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 23 |
|
|
|
|
|
|
|
|
|
| |||||||||
ISB2[3] | VCC Standby Current |
|
| > (VCC – 0.2V). All others VIN < 0.2V or > (VCC – 0.2V). |
| 1.5 | mA | ||||||||||
CE |
| ||||||||||||||||
| (Standby, Stable |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| CMOS Input Levels) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IIX | Input Leakage |
| VCC = Max, VSS < VIN < VCC |
|
| +1 | μA | ||||||||||
| Current |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IOZ | Off State Output |
| VCC = Max, VSS < VIN < VCC, |
| or |
| > VIH or |
|
| < VIL | +5 | μA | |||||
CE | OE | WE | |||||||||||||||
| Leakage Current |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VIH | Input HIGH Voltage |
|
|
|
|
|
|
|
|
|
|
|
|
| 2.2 | VCC + | V |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0.5 |
|
VIL | Input LOW Voltage |
|
|
|
|
|
|
|
|
|
|
|
|
| VSS – | 0.8 | V |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0.5 |
|
|
VOH | Output HIGH Voltage | IOUT = |
|
| 2.4 |
| V | ||||||||||
VOL | Output LOW Voltage |
| IOUT = 8 mA |
|
|
| 0.4 | V | |||||||||
Note
3. CE > VIH will not produce standby current levels until any nonvolatile cycle in progress has timed out.
Document Number: | Page 6 of 15 |
[+] Feedback