Cambridge Audio 840A RS232C BUS Ready/Incognito Ready multi-room outputs, Input 1 Balanced Audio

Page 7

840A Class XD integrated amplifier

6RS232C

The RS232C port allows external serial control of the 840A for custom install use. A full command set is available on the Cambridge Audio website at www.cambridge-audio.com. This port can also be used by Cambridge Audio service personnel for software updates.

7A-BUS™ Ready/Incognito Ready™ multi-room outputs

PSU - Connect an Incognito PS10 to supply power to the connected multi-room keypads/speakers.

Keypad 1/2 - Connect one or two Incognito A-BUS KP10 keypads (or other A-BUS compatible keypads) using CAT5/5e cable. Incognito AS10 Active Ceiling Speakers can also be connected here.

IR - Four IR outputs for remote control of source equipment.

Please refer to the ‘Multi-Room’ section of this manual for more information on connections and set-ups.

8Input 1 Balanced Audio

Input 1 features either unbalanced (phono/RCA) or balanced (XLR) connections. Either type may be used but not both at the same time. The balanced connection is the higher quality option and can reject noise and interference in the cable when used with other equipment that supports this function. An XLR connector is wired Pin 1 - Ground; Pin 2 - Hot (in-phase); Pin 3 - Cold (phase-inverted).

When using either the balanced or unbalanced input, make sure that no cables or equipment are connected to the unused input, as this may degrade operation. The unused input does not require to be terminated and this should not be done.

9Preamp Out

Connect these sockets to the inputs on an external power amplifier(s) or active subwoofers etc.

10Tape In/Out

Connect to a tape deck or to the analog output sockets on a MiniDisc, portable digital music player or CD recorder using an interconnect cable from the recorder's Line Out sockets to the amplifier's Tape In sockets.

The Tape Input circuit of the 840A is a "monitor" type, different from the other 7 inputs. For the 7 normal inputs, the source selected for listening to will be sent out of the Tape Out for recording. The source currently being listened to and (optionally) recorded is then shown on the front panel display.

However, when the Tape Input is selected a solid circle will appear beside TAPE MON indicating that the Tape Input is now being listened to with a different source being sent out of the Tape Out for recording. The recording source is also shown by a solid circle by the selected input and can be changed by pressing the other source buttons. To switch Tape Monitor off, simply press the Tape Mon input select button again, toggling this function off.

This feature is most useful when using 3-head analog cassette decks which allow the signal being recorded to be played back live off tape (via a 3rd head) whilst it is simultaneously recorded. It is then possible by toggling the Tape Monitor input on and off to compare directly in real time the original and recorded signal so that adjustments to the recording parameters of the tape machine can be made (consult the manual of your 3-head analog cassette deck for full details).

11Inputs 1-7

These inputs are suitable for any 'line level' source equipment such as CD players, DAB or FM/AM tuners etc.

Note: These inputs are for analog audio signals only. They should not be connected to the digital output of a CD player or any other digital device.

Azur Class XD integrated amplifier 7

Image 7
Contents Azur 840A Contents Introduction 840A Class XD integrated amplifierChecking the Power Supply Rating Safety PrecautionsPlug Fitting Instructions UK Only Important Safety Instructions Rear Panel Connections Tape In/Out RS232C BUS Ready/Incognito Ready multi-room outputsInput 1 Balanced Audio Preamp OutStandby/On Front Panel ControlsPhones Infrared sensor VolumeMode Bass and TrebleSpeakerA/B Speaker A/B Remote ControlNumerical buttons MuteBasic connection ConnectionsTape connection Preamp Out connections Speaker B connectionsBalanced audio connections Speaker A/B Operating InstructionsBalance Amplifier Setup Input gain trim Volume displayFixed level inputs 640T On/Off control menuPS10 MULTI-ROOMRemote control commands positive Custom Installation C.I. USEOvervoltage/overcurrent detection Over temperature detectionCAP5 Five WAY Protection System DC detectionIntelligent clipping detection Short circuit detectionTroubleshooting 840A Technical SpecificationsLimited Warranty 840A Class XD integrated amplifier Azur 840A