Technical Specifications

Model

PP1500

PP2200

Capacity

(VA)

1500VA

2200VA

Capacity

(Watts)

1000W

1500W

Input

Input Voltage Range

85Vac – 150Vac

Frequency Range

50/60 Hz +/- 3Hz

Output

On Battery Output Voltage

Pure Sine Wave at 120Vac +/- 7%

On Battery Output Frequency

47-53Hz for 50Hz nominal, 57-63Hz for 60Hz nominal

Transfer Time (Typical)

4ms

Overload Protection

On Utility: Circuit Breaker, On Battery: Internal Current Limiting

Surge Protection and Filtering

Lightning / Surge Protection

Yes

Internet Ready

RJ11/RJ45 (One In/One Out)

(DSL / Phone / FAX / Modem Protection)

Physical

Total # of UPS Receptacles

(8) NEMA 5-15R

(2) NEMA 5-20R

(6) NEMA 5-15R

Dimensions (cm)

42.0*18.0*23.5

Weight (kg)

25.4

31.1

Battery

Sealed Maintenance Free Lead Acid Battery

12V / 7.0AHx4

12V / 9.0AHx4

Hot Swappable Battery

Yes

Typical Recharge Time

8 Hours

Warning Diagnostics

Indicators

Power On, Using Battery, AVR, Wiring Fault, Load Level, Battery Level

Audible Alarms

On Battery, Low Battery, Overload

Environmental

Operating Temperature

+32°F to 95°F ( 0°C to 35°C )

Operating Relative Humidity

0% to 95% Non Condensing

Communication

PowerPanel Business Edition Software

Windows 95/98/ME/NT/2000/XP, Server 2003, Mac OSX, Linux

Management

Self-Test

Manual Self-Test

Auto-Charger/ Auto-Restart/USB

Yes

SNMP/ HTTP Network Card

Optional

DEFINITIONS FOR ILLUMINATED LED INDICATORS

Using

Condition

Circuit

Power On

Battery

Alarm

AVR

Breaker

Off

Set

Off

Normal

Slow flash

Off

Set

Off

AVR- Max. boost 13% of input voltage for output regulation while

input voltage is from 5% to 14% under nominal.

Rapid flash

Off

Set

Off

AVR- Max. boost 26% of input voltage for output regulation while

input voltage is from 15% to 29% under nominal.

Off

Set

Off

AVR- Max. buck 11% of input voltage for output regulation while

input voltage is from 8% to 25% over nominal.

Off

Set

Two Beeps

Utility Failure- The UPS is providing battery power to the

Battery-Power Supplied outlets.

Off

Set

Rapid Beeps

Utility Failure- The UPS is providing battery power. Rapid beeps

indicate the battery will run out of charge within a few minutes.

On/ Off

Overload- Turn the UPS off and unplug at least one piece of

On/Off

Set

Long Beep

equipment from the UPS. Wait 5 seconds, reset the circuit breaker

/Flash

and restart the UPS.

Overload- Turn the UPS off and unplug at least one piece of

Off

Long Beep

equipment from the UPS. Wait 5 seconds, reset the circuit breaker

and restart the UPS.

Off

Set

Off

Surge Protection Malfunction- Power surge has damaged the unit.

Please contact CyberPower Systems.

Limited Warranty and Connected Equipment Guarantee

Read the following terms and conditions carefully before using the CyberPower UPS (the “Product”). By using the Product you consent to be bound by and become a party to the terms and conditions of this Limited Warranty and Connected Equipment Guarantee (together referred to as this “Warranty”). If you do not agree to the terms and conditions of this Warranty, you should return the Product for a full refund prior to using it.

Who Is Providing This Warranty?

CyberPower Systems (USA), Inc. (“CyberPower”) provides this Limited Warranty.

What Does This Warranty Cover?

This warranty covers defects in materials and workmanship in the Product under normal use and conditions. It also covers equipment that was connected to the Product and damaged because of the failure of the Product.

What Is The Period of Coverage?

This warranty covers the Product for three years and connected equipment for as long as you own the Product.

Who Is Covered?

This warranty only covers the original purchaser. Coverage ends if you sell or otherwise transfer the Product.

How Do You Get Service?

1.Call us at (877) 297-6937 or write to us at Cyber Power Systems (USA), Inc., 4241 12th Ave. E., STE 400, Shakopee, MN 55379 or send us an e-mail message at claims@cpsww.com for instructions.

2.When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment. Have information on all applicable insurance or other resources of recovery/payment that are available to the Initial Customer and Request a Claim Number.

3.You must provide a purchase receipt (or other proof of the original purchase) and provide a description of the defect.

4.Pack and ship the product to CyberPower and, if requested, the item(s) of Connected Equipment, a repair cost estimate for the damage to the Connected Equipment, and all claim forms that CyberPower provides to you. Show the Claim Number on the shipping label or include it with the product. You must prepay all shipping costs, you are responsible for packaging and shipment, and you must pay the cost of the repair estimate.

How Long Do I Have To Make A Claim?

All claims must be made within ten days of the occurrence.

What Will We Do To Correct Problems?

CyberPower will inspect and examine the Product.

If the Product is defective in material or workmanship, CyberPower will repair or replace it at CyberPower's expense, or, if CyberPower is unable to or decides not to repair or replace the Product (if defective) within a reasonable time, CyberPower will refund to you the full purchase price you paid for the Product (purchase receipt showing price paid is required).

If it appears that our Product failed to protect any equipment plugged into it, we will also send you forms for making your claim for the connected equipment. We will repair or replace the equipment that was damaged because of the failure of our Product or pay you the fair market value (NOT REPLACEMENT COST) of the equipment at of the time of the damage. We will use Orion Blue Book, or another a third-party valuation guide, or eBay, craigslist, or other source to establish that amount. Our liability is limited to the Connected Equipment Guarantee amount as stated in the Technical Specifications section.

Who Pays For Shipping?

We pay when we send items to you; you pay when you send items to us.

What Are Some Things This Warranty Does Not Cover?

1.This Warranty does not cover any software that was damaged or needs to be replaced due to the failure of the Product or any data that is lost as a result of the failure or the restoration of data or records, or the reinstallation of software.

2.This Warranty does not cover or apply to: misuse, modification, operation or storage outside environmental limits of the Product or the equipment connected to it, nor for damage while in transit or in storage, nor if there has been improper operation or maintenance, or use with items not designed or intended for use with the Product, such as laser printers, appliances, aquariums, medical or life support devices, etc.

What are the Limitations?

1.This Warranty does not apply unless the Product and the equipment that was connected to it were connected to properly wired and grounded outlets (including compliance with electrical and safety codes of the most current electrical code), without the use of any adapters or other connectors.

2.The Product must have been plugged directly into the power source and the equipment connected to the Product must be directly connected to the Product and not “daisy-chained” together in serial fashion with any extension cords, another Product or device similar to the Product, surge suppressor, or power tap. Any such installation voids the Limited Warranty.

3.The Product and equipment connected to it must have been used properly in a suitable and proper environment and in conformance with any license, instruction manual, or warnings provided with the Product and the equipment connected to it.

4.The Product must have been used at all times within the limitations on the Product’s VA capacity.

Where Can I Get More Information?

For further information please feel free to contact CyberPower at Cyber Power Systems (USA), Inc. 4241 12th Ave E., STE 400, Shakopee, MN 55379; call us at (877) 297-6937; or send us an e-mail message at claims@cpsww.com.

FCC Notice

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING!! This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna.

(2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help. Any special accessories needed for compliance must be specified in the instruction.

The Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulation. Cet appareil numerique de la class B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada