B&B Electronics 232MSS2 manual Parameters, Type Sstsr A03F8 B7 D8 P1 U8 H6 and press the Enter key

Page 20

If the software was installed in the default directory:

At the DOS prompt Type C: and press the ENTER key.

Type CD\232MSS2 and press the ENTER key.

To begin the SSTSR program (the following will be used as an example):

Port Address = 03F8 Parity = Odd Baud = 9600 User Defined Char. = 8

Data Bits = 8 Hot Key Sequence = 4

Type SSTSR A03F8 B7 D8 P1 U8 H6 and press the ENTER key.

Using this method, every time you want to install the SSTSR

with different parameter settings than the default (refer to the Default Values section), the missing parameter must be specified.

Parameters

The Port Address is the address where the serial communications port is located.

Some of the typical port addresses are as follows:

Port

Address

COM 1

03F8h

COM 2

02F8h

COM 3

03E8h

COM 4

02E8h

The Baud Rate is the speed at which communication takes place between the SSTSR and the Smart Switch. It must be specified so that it is equal to SW1 on the Smart Switch.

The Number of Data Bits is the length of each character that gets sent from the SSTSR to the Smart Switch. This value must be specified so that it is equal to SW2 on the Smart Switch.

The Parity is a method of error detection that takes place during the transmission of data between the SSTSR and the Smart Switch. This value must be specified so that it is equal to SW2 on the Smart Switch.

The User Defined Character must be set so that it is equal to SW3 on the Smart Switch.

16Documentation Number 232MSS2-0108 Manual

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

Image 20
Contents Mini Smart Switch CE Page Table of Contents Table of Contents Documentation Number 232MSS2-0108 Manual Introduction Checklist Setup Communication & Port Setup Dipswitch SW1 3 4 5 6 7 SettingPin# Direction Description Port ConfigurationDCE Master Port Chart C & D Ports DTE Master Port Chart C & D Ports Serial Data ConfigurationSmart Switch Operation ESC STX B Programmable Character Setting Dipswitch SW2* WeightProgramming the Second Character Binary File TransferSmart Switch/Port Combiner Mode Enhanced Mode -- Timer Features Timer Values Specifications Model 232MSS2Documentation Number 232MSS2-0108 Manual Windows SSwitch InstallationRunning SSwitch Software IntroductionSETUP.EXE Method preferred DOS SstsrCommand Description Options SSTSR.EXE MethodPort Address ParametersType Sstsr A03F8 B7 D8 P1 U8 H6 and press the Enter key Selecting Ports Default ValuesHelp Screen Un-Install Hot Key Method Command Line Method Documentation Number 232MSS2-0108 Manual Appendix a Decimal to HEX to Ascii Conversion Table Appendix B Chart 1. IBM PC DB25 Connector to Master Port Chart 2. IBM PC DB9 Connector to Master PortChart 3. Modem DB25 Connector to Master Port Async Modem Chart 4. IBM PC DB25 Connector to Ports a D DTEDB9 Connector Direction 232MSS2 Ports a D DTE Chart 5. IBM PC DB25 Connector to Ports a D DCEChart 6. IBM PC DB9 Connector to Ports a D DTE Chart 7. IBM PC DB9 Connector to Ports a D DCE DB9 Connector Direction 232MSS2 Ports a D DCEChart 8. IBM PC DB25 Connector to Ports a D DCE DB25 Connector Direction DB9 ConnectorChart 9. IBM PC DB9 Connector to Ports a D DCE DB9 Connector DirectionAppendix C Declaration of Conformity Declaration of ConformityAppendix C Documentation Number 232MSS2-0108 Manual