Editing a Loop, Pitch Bending, JOG Wheel

BASIC OPERATIONS (CONT.)

• Replay Loop

The RELOOP (16) function allows you to return to your stored loop at any time. The IN/R CUE (12) and OUT/EXIT (14) LEDs will indicate a loop is stored in memory, and may be played at any time. To replay the loop, press the RELOOP BUTTON (16). The IN/R. CUE (12) and OUT/EXIT (14) LEDs will again begin to flash indicating SEAMLESS LOOP mode has been activated (Fig. 14) and your stored loop will immediately begin to play.

11. EDITING A LOOP:

Please note you can only edit the ending point of the loop. You may make your loop shorter or longer. Before you can edit your seamless loop you obviously must first have created a seamless loop to edit. If you haven’t created a SEAMLESS LOOP, follow instructions on page 11 “creating and play a seamless loop”. If a SEAM- LESS LOOP has already been created, press the RELOOP BUTTON (16) to restart your SEAMLESS LOOP (Fig. 14) if is not already playing. To edit your seamless loop’s ending point:

1)Press the OUT/EXIT BUTTON (14) to return to normal play from the the loops cue point. (Fig. 13). This will disengage the SEAMLESS LOOP mode and allows you to edit the loops ending point.

2)Press the OUT/EXIT BUTTON (14) again when you reach your new ending point (Fig. 13).

3)FOR A SHORTER LOOP: Press the OUT/EXIT BUTTON (14) at sooner point in the track.

4)FOR LONGER LOOP: Press the OUT/EXIT BUTTON (14) at later point in the track.

12. TIME METER DISPLAY (44)/TIME BAR (46)

During normal playback, pressing the TIME BUTTON (6), will change the display time display information (44) to one of the following settings:

1)ELAPSED - This describes the current tracks elapse running time (45).

2)REMAIN - This describes the track remaining running time (36).

3)TOTAL - This indicator along with REMAIN will glow simultaneously indicating the total remaining running time of the load disc (35).

TIME BAR INDICATOR - Shows the time length defined in the TIME METER (44). As with the TIME METER

(44)this bar is also dependent on the selected function displayed above the TIME METER as TOTAL REMAIN (35), REMAIN (36) OR ELAPSE (45). This bar will also begin to flash when a track is ending regardless of which time function you are in.

13. PITCH BENDING

This function will provide a momentarily increases or decreases the tracks playback speed. There are two ways to operate this function with the (-) & (+) PITCH BUTTONS (13 & 20) or with the JOG WHEEL (7). The SLID- ERS PITCH ADJUSTMENT (18) can be changed from +/-8%, +/-12%, or +/-16% range (See changing PITCH PERCENTAGE Page 8 Sec 9) and the pitch bending will work in conjunction with the PITCH SLIDER (18) pitch setting. For example, if the PITCH SLIDER (18) is set to a 2% pitch gain the pitch bending process will begin at 2% and will continue to the maximum of -/+16%.

PITCH BEND BUTTONS (13 & 20):

The (+) PITCH BEND (13) button will provide a speed bump and the (-) PITCH BEND (20) button will provide a slow down. The extent to which the speed changes is proportionate to the amount of time the button is pressed. For example, if the (+) PITCH BEND BUTTON (13) is held down continuously, the disc speed will increases and will continue to increase until reaches a maximum of 16% speed gain. When you release the (+) PITCH BEND BUTTON (13) the disc speed will automatically return to it’s previous speed.

JOG WHEEL (7):

The JOG WHEEL (7) will temporarily bend the pitch if a track is in play mode. Rotating the wheel in a clock- wise direction will increase your track pitch and rotating the wheel in a counter-clockwise direction will slow your track pitch. The speed you rotate the JOG WHEEL (7) will determine pitch bend percentage (%).

14. TRACK PROGRAM PLAY

This operation allows you to customize your disc playback. You may select specific tracks to played and the order they will be played in. You may program a maximum of 20 tracks at once and program a single track to

American DJ® AUDIO • PRO DJ3™ • INSTRUCTION MANUAL • PAGE 12