Sierra Wireless MP 880W manual Plan your MP modem installation

Page 20

MP880W Modem User Guide

Plan your MP modem installation

This section guides you through the decisions you need to make before you begin the installation.

Where do you want to install your MP modem?

The MP modem can be installed in a vehicle or in an office. The same installation steps apply with the following exceptions:

If you are installing the MP modem in a vehicle:

·Use the power harness to connect the MP modem to the vehicle battery.

·Decide how to set the ignition sense option for powering the MP modem on and off (that is, depending on the ignition switch wiring, the MP modem can be turned on when the engine is started, when the ignition is in accessory mode, or independently of the ignition).

If you are installing the MP modem in an office, an AC/DC adapter is available.

What type of connection(s) do you plan to use?

The MP modem is capable of the following kinds of network connections:

Serial

USB

Ethernet

Wireless Access Point via IEEE 802.11b/g (MP W only)

Data transfer rates vary, depending on the network, but note that the highest data rate using a serial connection is

115.2 kbps.

Before deciding which network interface to use, you need to understand the advantages and disadvantages of each, and any other implications of using one interface over another.

 

 

 

 

 

 

 

20

 

 

 

 

 

2130795

 

 

 

Image 20
Contents User Guide Page Contents MP Modem Operation Configuring the Router Functions Support and Warranty Regulatory Information MP880W Modem User Guide 2130795 Important Notice Safety and Hazards Limitation Liability Patents Copyright Qualcomm 3GSupport@sierrawireless.com Trademarks Contact InformationDirecting users to the MP 3G Modems AT Command Reference Revision HistoryIntroducing the MP Modem Network connections Accounts and coverageSupported GSM radio frequencies Connection methodsVirtual serial port VPN support for Rnap SoftwareDocumentation MP Modem ManagerMP880W Modem User Guide Getting Started What type of connections do you plan to use? Plan your MP modem installationWhere do you want to install your MP modem? Getting Started Additional required equipment Package contentsRequired equipment MP modem accessories System requirementsMP880W Modem User Guide 2130795 MP modem housing Hardware and Software InstallationInstallation overview GPS and I/O options Connector panelOverview of installation steps Install the MP modem Mount the MP modemSelect a location for the MP modem Mounting the MP modemGround the MP modem Mount the antennas and install the cables Main RF antennaAntenna locations GPS antennaAP antenna MP 595880W only Install the power harness Install the antennas and cablesPower connector Power connector Molex pinoutsVehicle installation Ignition sense on/off wiringIgnition sense options Ground the power harness Power connectionsCorrect wire splicing Crimp terminalsOffice installation Connect the MP modem to computer cableSerial connector DB9 pinouts Install the USB, Ethernet or serial cablePort connections Install the softwareConfigure your account Insert the SIM Card 10 Placing a SIM card into the sledSet up connection profiles Create a profile· User Name Test the system MP880W Modem User Guide 2130795 MP Modem Operation Turning the MP modem on and offStatus indicators LED operation3G Watcher Help Reset the MP modem3G Watcher software Changing the Physical Interface Launching 3G WatcherConnection to MP Physical Interface Establishing connections 3G Watcher windowAuto-Connect for DUN You now have DUN connectionConfiguring the Router Functions NAT modeNon-NAT mode NAT modeMP modem networking basics in NAT ModeStatic IP and TCP/UDP port forwarding in NAT mode Enable the routerSet up static IP addresses File and resource sharing over LANSet up TCP/UDP port forwarding MP880W Modem User Guide 2130795 Configuring the Wireless Access Point OverviewUnlock MP modem configuration Change the password optionalEnable the wireless access point Set the SsidConfigure the security settings Reset the MP modem to factory defaults Configure security on the client computersMP880W Modem User Guide 2130795 Configuring the MP Modem to Report GPS and I/O Data GPS configuration and reportingGPS protocols and commands GPS display in 3G WatcherDevice installation and configuration GPS Taip quick referenceDigital input devices Connector pinoutsPort specifications A button wired to Pin 4 digital input and Pin 10 Ground Example panic button connectionsDigital output devices Analog input devicesConfiguration using AT or 3G Watcher commands Example analog sensor connectionsAnalog input setup ExampleDigital I/O setup MP880W Modem User Guide 2130795 Configure the MP modem to Report frequency timersSending Data to Your Network Application Route data to a serverTmsumregind Sending Data to Your Network Application Monitoring and Tracking configuration IP AddressingProblem created by Network Address Translation Solutions to the NAT problem Retrieve the Unique Mobile Device IDTechnical support Support and WarrantyWarranty MP880W Modem User Guide 2130795 Technical Specifications Regulatory, radio frequency and electrical specificationsEnvironmental specifications Weight and dimensionsGPS specifications Port characteristicsHost interfaces Other interfacesWireless access point specifications WPA2Regulatory Information CanadaImportant Note FCC CautionApproved antennas European UnionRegulatory Information MP880W Modem User Guide 2130795 Index NumericsMTP Index Index Rev 1.1 Jul.08

MP 880W specifications

Sierra Wireless MP 880W is a robust and versatile wireless communication solution designed primarily for the high-demand requirements of industrial and enterprise applications. With its cutting-edge technologies and features, the MP 880W stands out as a reliable solution for IoT connectivity and data transmission.

One of the key features of the Sierra Wireless MP 880W is its multi-connectivity capability. It supports 4G LTE, 3G, and Wi-Fi, enabling users to maintain a consistent and reliable connection regardless of their location. This versatility allows businesses to operate in remote areas while ensuring that critical data is transmitted seamlessly.

The device is equipped with advanced security features including VPN support, firewall capabilities, and secure access protocols. This ensures that sensitive information remains protected against unauthorized access and cyber threats, which is crucial for businesses that rely on data integrity and security.

The MP 880W also boasts high-speed connectivity, capable of reaching download speeds of up to 150 Mbps. This is particularly beneficial for applications that require real-time data analytics or streaming, such as remote monitoring and management systems. The device can handle multiple connected devices simultaneously, making it a suitable choice for environments with multiple IoT devices.

Another notable characteristic of the Sierra Wireless MP 880W is its rugged design, built to withstand harsh environmental conditions. With an extended temperature range and robust housing, the device is suitable for outdoor deployment in industries such as transportation, oil and gas, and agriculture.

The MP 880W provides easy integration with existing IT infrastructure, thanks to its compatibility with various networking standards. Users can deploy it quickly and effectively, minimizing downtime and streamlining operations.

Furthermore, the device offers extensive support for various IoT protocols, making it adaptable for numerous applications. Whether it's for smart cities, asset tracking, or industrial automation, the MP 880W delivers the performance and reliability needed in today’s fast-paced, technology-driven environment.

In summary, the Sierra Wireless MP 880W combines high-speed connectivity, security features, rugged design, and multi-connectivity capabilities, making it a premier choice for industrial IoT applications. Its adaptability to various environments and ease of integration solidify its reputation as a leading wireless communication solution in the market.