Sierra Wireless MP 880W manual Configuring the Wireless Access Point, Overview

Page 55

6: Configuring the Wireless Access Point

• Unlock MP modem

 

configuration

This chapter describes how to use the MP 880W modem as a

• Enable the wireless

wireless access point. You can use the MP 880W as a wireless

access point

access point in either NAT or non‐NAT modes1.

• Set the SSID

 

• Configure the security

Note: This chapter only applies to the MP 875W.

settings

 

 

• Reset the MP modem

 

to factory defaults

Overview

 

By default the wireless access point is disabled. The main steps

 

for configuring the MP modem wireless access point are:

 

• Enable wireless access point.

Optional:

•Change the password.

•Set the SSID.

•Set the security settings.

•Enable NAT, if applicable. (See Chapter 5 for details.)

Note: Watcher is currently not available over a WAP network. You can use Watcher over any Physical Interface to enable the WAP interface.

Note: If the Wi-FI is enabled and is in Non-NAT mode, the computer that is connected to the Wi-Fi can monitor cellular connection by using ethernet through the watcher.

1.See Chapter 5 for information on enabling and configuring NAT mode.

 

 

 

 

 

 

 

Rev 1.5 Jul.08

 

 

 

 

 

49

 

 

 

Page 54 Page 56
Image 55
Page 54 Page 56
Contents User Guide Page Contents MP Modem Operation Configuring the Router Functions Support and Warranty Regulatory Information MP880W Modem User Guide 2130795 Important Notice Safety and Hazards Limitation Liability Qualcomm 3G Patents CopyrightTrademarks Contact Information Support@sierrawireless.comRevision History Directing users to the MP 3G Modems AT Command ReferenceIntroducing the MP Modem Accounts and coverage Network connectionsVirtual serial port Connection methodsSupported GSM radio frequencies Software VPN support for RnapMP Modem Manager DocumentationMP880W Modem User Guide Getting Started Where do you want to install your MP modem? Plan your MP modem installationWhat type of connections do you plan to use? Getting Started Required equipment Package contentsAdditional required equipment System requirements MP modem accessoriesMP880W Modem User Guide 2130795 Installation overview Hardware and Software InstallationMP modem housing Overview of installation steps Connector panelGPS and I/O options Mounting the MP modem Install the MP modemMount the MP modem Select a location for the MP modemGround the MP modem Main RF antenna Mount the antennas and install the cablesAP antenna MP 595880W only GPS antennaAntenna locations Install the antennas and cables Install the power harnessIgnition sense on/off wiring Power connectorPower connector Molex pinouts Vehicle installationIgnition sense options Crimp terminals Ground the power harnessPower connections Correct wire splicingConnect the MP modem to computer cable Office installationInstall the USB, Ethernet or serial cable Serial connector DB9 pinoutsConfigure your account Install the softwarePort connections 10 Placing a SIM card into the sled Insert the SIM CardCreate a profile Set up connection profiles· User Name Test the system MP880W Modem User Guide 2130795 Turning the MP modem on and off MP Modem OperationLED operation Status indicators3G Watcher software Reset the MP modem3G Watcher Help Connection to MP Physical Interface Launching 3G WatcherChanging the Physical Interface 3G Watcher window Establishing connectionsYou now have DUN connection Auto-Connect for DUNNAT mode Configuring the Router FunctionsNAT mode Non-NAT modeMode MP modem networking basics in NATFile and resource sharing over LAN Static IP and TCP/UDP port forwarding in NAT modeEnable the router Set up static IP addressesSet up TCP/UDP port forwarding MP880W Modem User Guide 2130795 Overview Configuring the Wireless Access PointChange the password optional Unlock MP modem configurationSet the Ssid Enable the wireless access pointConfigure the security settings Configure security on the client computers Reset the MP modem to factory defaultsMP880W Modem User Guide 2130795 GPS configuration and reporting Configuring the MP Modem to Report GPS and I/O DataGPS display in 3G Watcher GPS protocols and commandsGPS Taip quick reference Device installation and configurationPort specifications Connector pinoutsDigital input devices Example panic button connections A button wired to Pin 4 digital input and Pin 10 GroundAnalog input devices Digital output devicesExample analog sensor connections Configuration using AT or 3G Watcher commandsExample Analog input setupDigital I/O setup MP880W Modem User Guide 2130795 Route data to a server Configure the MP modem toReport frequency timers Sending Data to Your Network ApplicationTmsumregind Sending Data to Your Network Application IP Addressing Monitoring and Tracking configurationProblem created by Network Address Translation Retrieve the Unique Mobile Device ID Solutions to the NAT problemWarranty Support and WarrantyTechnical support MP880W Modem User Guide 2130795 Regulatory, radio frequency and electrical specifications Technical SpecificationsWeight and dimensions Environmental specificationsOther interfaces GPS specificationsPort characteristics Host interfacesWPA2 Wireless access point specificationsCanada Regulatory InformationEuropean Union Important NoteFCC Caution Approved antennasRegulatory Information MP880W Modem User Guide 2130795 Numerics IndexMTP Index Index Rev 1.1 Jul.08

MP 880W specifications

Sierra Wireless MP 880W is a robust and versatile wireless communication solution designed primarily for the high-demand requirements of industrial and enterprise applications. With its cutting-edge technologies and features, the MP 880W stands out as a reliable solution for IoT connectivity and data transmission.

One of the key features of the Sierra Wireless MP 880W is its multi-connectivity capability. It supports 4G LTE, 3G, and Wi-Fi, enabling users to maintain a consistent and reliable connection regardless of their location. This versatility allows businesses to operate in remote areas while ensuring that critical data is transmitted seamlessly.

The device is equipped with advanced security features including VPN support, firewall capabilities, and secure access protocols. This ensures that sensitive information remains protected against unauthorized access and cyber threats, which is crucial for businesses that rely on data integrity and security.

The MP 880W also boasts high-speed connectivity, capable of reaching download speeds of up to 150 Mbps. This is particularly beneficial for applications that require real-time data analytics or streaming, such as remote monitoring and management systems. The device can handle multiple connected devices simultaneously, making it a suitable choice for environments with multiple IoT devices.

Another notable characteristic of the Sierra Wireless MP 880W is its rugged design, built to withstand harsh environmental conditions. With an extended temperature range and robust housing, the device is suitable for outdoor deployment in industries such as transportation, oil and gas, and agriculture.

The MP 880W provides easy integration with existing IT infrastructure, thanks to its compatibility with various networking standards. Users can deploy it quickly and effectively, minimizing downtime and streamlining operations.

Furthermore, the device offers extensive support for various IoT protocols, making it adaptable for numerous applications. Whether it's for smart cities, asset tracking, or industrial automation, the MP 880W delivers the performance and reliability needed in today’s fast-paced, technology-driven environment.

In summary, the Sierra Wireless MP 880W combines high-speed connectivity, security features, rugged design, and multi-connectivity capabilities, making it a premier choice for industrial IoT applications. Its adaptability to various environments and ease of integration solidify its reputation as a leading wireless communication solution in the market.
Top Page Image Contents