Sierra Wireless 20070914 manual Serial, D.d=IP address

Page 111

Configuration Commands

*NETROAMPREF=n

Allow configuration of the roaming preference.

•n=0 : Restrict to home network only.

•n=1‐3 : Allow roaming to affiliated networks.

n=3

*NETUID=uid

The login that is used to login to the cellular network, when required.

•uid=user id (up to 64 bytes)

*STATICIP=d.d.d.d

Set the static IP required to be received from the network. If the modem does not get this IP address from the network, it will reset the internal hardware and try again. The default is 0.0.0.0, which allows any IP address from the network.

•d.d.d.d=IP address

Example:

AT*STATICIP=192.168.1.23

Caution: STATICIP does not set the IP address of the modem, it merely tells the modem which IP address to expect. If the expected IP address is not granted while registering on the cellular network, the modem will try to register on the network again until it receives that IP address. If your account is set up for a dynamic IP address and you set an address for *STATICIP, you may not be able to register on the network at all since there is no guarantee you will receive the same dynamic IP address again.

*STATUSCHK=n

Checks if an SMS message has been received by the modem.

•n=1‐255 : Seconds between checks.

•n=0 : Never check.

Serial

This group includes commands specific to general use of the serial port.

 

 

 

 

 

 

 

Rev 3.0B Feb.08

 

 

 

 

 

106

 

 

 

Page 110 Page 112
Image 111
Page 110 Page 112
Contents User Guide Important Notice Safety and Hazards Limitation Liability Qualcomm 3G Patents Copyright TrademarksContact Information Support@sierrawireless.comRevision Release Changes Number Date Revision HistoryContents Configuring your Raven Configuring Modbus/BSAP Contents Contents Contents Circuit Switch Communications Contents Connecting to the Internet Using DUN Aleos Introduction to the RavenAceManager AceWareMonitor and Control Simplified DeploymentAceNet AceViewNetwork Monitoring Modem Doctor Setup WizardModem Doctor Modem Doctor USBSteps of a connection Connecting to the Sprint NetworkDynamic vs. Static IP Addresses Connecting to the InternetSecurity 1x CommunicationSpecifications Interface Port Pin-Outs Power ConnectorSetup Wizard Starting the Setup WizardActivating your Raven on Sprint Network Setup Wizard Connecting to the ModemSelecting Tasks Setup Wizard ConnectedAleos Update OptionalUpdate AleosActivate Modem Setup Wizard MSLSetup Wizard MDN and MIN/MSID Vision C3210 Setup Wizard Vision Configuration11 Setup Wizard Vision Home Agent IP Addresses Test Modem Setup13 Setup Wizard Connection Test Data Link Configuration14 Setup Wizard Data Link NAI 15 Setup Wizard Primary and Secondardy HA 17 Setup Wizard Passwords Optional Setting up a DUN Connection19 Setup Wizard DUN settings 21 Setup Wizard DUN settings Activating Using AT CommandsUsing Aleos Using Direct Commands to the Internal HardwareActivating the Modem Data Link Indicator Lights Hardware Installation RavenConnecting to Power Indicator Lights Connecting to a Computer or other DeviceLight Patterns MountingOptional Mounting Bracket Hardware Installation of the Raven Rev 3.0B Feb.08 Hardware Installation of the Raven Rev 3.0B Feb.08 Configuring your Raven Using AceManagerStart AceManager AceManager Connect to Modem Connect to your RavenAceManager Connected Enter the configuration optionsUsing Templates Write the changes to the modemCreating the Template with AceManager · Cellular Technology specific settings the CDMA/EV‐DO group Applying a Template to one modem with AceManager Reset the modemConfiguring your Raven 10 AceNet Selected modems Choose a name and icon for your connection Using a Terminal Application with AT CommandsConnect To Port Settings serial only· Flow Control Hardware ConnectedAT Commands Data Communication and Host 6 Modes Basic ModesSerial Modes Start up Mode Basic ModesData Communication AT Mode AceManager PassThru PassThru ModeSerial Modes Telnet ModeAT\APPP UDP Auto Answer UDP and UDP PadReliable UDP TCP and TCP Pad UDP Multicast ModeTCP Auto Answer Hybrid ModesUdplast Data Communication Public and Private ModeKeepalive Data usage using Keepalive Configuring KeepaliveIpping Reasons to contact the modem and/or the connected device IP ManagerUnderstanding Domain Names Dynamic Names Car54.mydomain.comCar54.mydomain.com.ca AceManager Dynamic IP Using IP Manager with your RavenData Usage for IP Manager Server Updates Eairlink.comRestrictions for Modem Name Understanding DNS Configuring DNSAceManager DNS PPP-Peer Domain NameRemote Terminal Unit RTU Configuring Modbus/BSAPModbus Overview TelemetryRaven Modbus on UDP Supervisory Control and Data Acquisition ScadaProgrammable Logic Controller PLC Modbus TCP/IPConfigure the listening/device ports Configuring the Raven at Polling Host for Modbus onConfigure IP addresses for the Modbus IDs Configure the default mode for start-upOptional Dynamic IP Address Configure the ports Configuring the Remote Ravens for Modbus with UDPAceManager UDP Configure IP addresses for the hostConfigure other RTU settings AceManager DNS Raven 20070914 Snmp Simple Network Management Protocol Management Information Base MIBSnmp Traps Snmp Configuration Listening PortSecurity Level AceManager Change Password menu option User Name and PasswordSnmp MIB Definition Sample Trap DestinationCommunity String Snmp Simple Network Management Protocol Snmp Simple Network Management Protocol Snmp Simple Network Management Protocol Display Responses Product ID Info information Configuration CommandsNETPHONE? DEVICEID?NETERR? StatusHOSTMODE? NETCHAN?Any other value Failure AT Commands Requiring PassThru mode +WPRL? +ECIO?+GSN +WHWVCommon Misc Miscellaneous+++ DS=n Dmethodd.d.d.d/ppppp or Dmethod@name/ pppppOPRG=n S53=methodd.d.d.d/pppppMethod= P UDP Method=T TCP Method=N Telnet =1‐65535 D.d=IP address SerialS3=n S4=nS5=n Parity=O Odd Parity=E Even Parity=N None Parity=M Mark =2‐10 seconds=0‐255 =1‐2545S211=n S50=n=tenths of a second S51=n$QCVAD=n \APPP\Qn +IPR=nPPPNOCARRIER=n CTSE=nModemhispeed NUMTOIP=nS60=n S0=nS7=n =seconds=interval =0 ‐Hh=33 Bsap HOR=nMDhh Hh=01 Slip Hh=02 PPP Hh=03 UDP Hh=04 TCPUDPLAST=n S83=nDU=n UALL=nDNSUSER=d.d.d.d DNSUPDATE=nDynamic IP D.d=IP address of domain serverDOMAIN=name Name=domain nameIPMGRKEYn=key IPMGRUPDATEn=m PPP/EthernetMODEMNAME=name DHCPSERVER=n HOSTAUTH=nHOSTNETMASK=n.n.n.n String=password PassThruD.d=local or peer IP address of the modem PTINIT=string String=AT commands\APASSTHRU CSX1=n=1‐255 hours RESETPERIOD=nPTREFRESH=n =1‐255 minutesSMTPSTATUS? Pw= password=SMS/E‐mail server number Email=email address Body=message bodySubject=message subject Cntsms DasmsIndex= index list 0, 1 Message= message number DATZ=n OtherSSMS? DAE=nName=domain name Port=port Resetcfg=15‐255 minutes D.d=IP address Name=domain name=1 On Host=IP address Port=TCP portTPORT=n TELNETTIMEOUT=nFriends =minutesLogging FM=nD.d = IP address DBGPPPLVL=n Telemetry/Addr ListDBGCOMMLVL=n DBGIPLVL=nHh=hex value IPL=nMVLEN=n MVMSK=hhRKEY=n Addr ListMVOPT=n MVTYP=n+CTA=n 1x/EV-DOId=ID D.d=IP address or name Hexid=ID D.d=IP address or namePROVISION2=MSL,MDN,MIN,SID,NID ~NAMLCK=nnnnnnNnnnnn=6 digit unlock code PROVISION=MSL,MDN/MIN,SID,NID+WIMI=num +WMDN=numNam=0 Min=phone number Msid=second number Sid=system ID Nid=network IDConfiguring Circuit-Switch Circuit Switch Communications BAT Commands and the Command String Commands Specific to the Raven 1x C3211 Commands Specific to the Raven 1x C3210 and C3216Step by Step Configuration Raven LEDs in Circuit-Switched ModeCommon AT Commands Software Required Hardware RequiredConnect the modem to your computer Erase the internal memoryInformation Required for CDMA/1x only Rev 3.0B Feb.08 144 Start All Programs AirLink Communications AceManager 3G Activate the RavenSave the serial setting Configure serial port speed12 AceManager Disconnect Configure the Raven using a AceManager template15 AceManager Load Configure additional PassThru settingsTest the Raven Configuration Save the configuration settingsConfigure the Raven for your equipment Reset the RavenCommission the Raven Modem on Site 151 20070914 Connect the Raven Installing a modem driver for RavenInstall the driver Windows Dial-up Networking C DUNSelect the Modems tab Check Don’t detect my modem I will select it from a list Check Selected Ports Modem Properties Configure the driverModem Properties Modem Creating a Dial-Up Networking PPP Connection10 Windows Start menu Create a new network connectionSelect Connect to the Internet Select Set up my connection manually Rev 3.0B Feb.08 161 Rev 3.0B Feb.08 162 21 New Connection Finish Configure the DUN connectionCheck Show icon...when connected Rev 3.0B Feb.08 165 Select Advanced Start AceView Connecting to the Internet Using DUNWindows DUN Enable the ConnectionSelect Dial to connect to the modem and the cellular network Start the DUN sessionWindows Dial-up Networking DUN Rev 3.0B Feb.08 170
Related manuals
Manual 36 pages 19.88 Kb Manual 171 pages 23.08 Kb Manual 203 pages 17.49 Kb

20070914 specifications

Sierra Wireless 20070914 is a cutting-edge wireless communication module designed for IoT applications, offering remarkable features and robust performance. This module represents a significant advancement in the realm of embedded wireless solutions, catering to a variety of industries including automotive, industrial automation, and smart cities.

One of the key features of the Sierra Wireless 20070914 is its support for multiple cellular standards, including LTE, which ensures high-speed data transfer and reliable connectivity. The module is designed to operate on various frequency bands, making it versatile and suitable for global deployment. This multi-band capability allows businesses to deploy their IoT solutions in different regions without modification, reducing time-to-market and deployment costs.

Another standout characteristic of the Sierra Wireless 20070914 is its comprehensive and seamless integration with cloud services. The module supports advanced cloud connectivity options, enabling real-time data processing and analysis, which is crucial for industries that rely on timely decision-making. This feature is particularly important in sectors like transportation and logistics, where real-time tracking and monitoring are essential.

The power efficiency of the Sierra Wireless 20070914 is noteworthy. It is engineered to operate optimally in low-power modes, making it ideal for battery-operated devices. This focus on energy efficiency ensures prolonged device lifecycles, supporting the growing demand for sustainable and eco-friendly technologies.

Moreover, the module includes encrypted communication features, enhancing security and protecting sensitive data transmissions. With the increasing prevalence of cyber threats, this security aspect is critical for businesses looking to safeguard their IoT applications from unauthorized access and data breaches.

In addition to these features, the Sierra Wireless 20070914 offers comprehensive development support, including software development kits (SDKs) and application programming interfaces (APIs). This makes it easier for developers to integrate the module into their existing systems, streamlining the development process and accelerating innovation.

Overall, the Sierra Wireless 20070914 stands out as a powerful solution for IoT connectivity, blending advanced technology, security, and efficiency. Its capabilities are designed to support the diverse needs of modern industries, paving the way for future innovations and advancements in wireless communication. As businesses increasingly turn to IoT for modernization, modules like the Sierra Wireless 20070914 will play a crucial role in enabling this transformation.
Top Page Image Contents