Sierra Wireless 20070914 manual =2‐10 seconds, =0‐255, =1‐2545

Page 113

Configuration Commands

S6=n

This register denotes the wait time, in seconds, before a blind dial (no dial tone detection). Cannot be configured in AceManager.

•n=2‐10 seconds

S8=n

Whenever a dial command contains the comma character, the contents of this register specify the pause time for each comma. Cannot be configured in AceManager.

•n=0‐255

S9=n

Specifies the time that the received carrier must be present for the modem to recognize it and turn on Data Carrier Detect (DCD) if applicable. The implementation is entirely at the IWF modem. Cannot be configured in AceManager.

•n=0‐255

S10=n

Specifies the amount of time that the carrier from the remote modem can be lost before the modem goes on‐hook. This allows temporary disruptions to carrier without disconnecting. A setting of 255 causes the modem to disable Carrier Detect and presume carrier is always present. Cannot be configured in AceManager.

•n=1‐2545

S23=[speed],[databits][parity][stop bits]

Serial line parameters. The settings take affect after reset.

•speed=300 1200 2400 4800 9600 19200 38400 57600 115200 230400

•databits=7 or 8 (Databits MUST be 8 data bits for PPP mode.)

•parity=O : Odd

•parity=E : Even

•parity=N : None

•parity=M : Mark

•stopbits=1 1.5 2

Example:

ATS23=19200,8N1

Sets modem to 19200, 8 databits, no parity, and 1 stop bit.

 

 

 

 

 

 

 

Rev 3.0B Feb.08

 

 

 

 

 

108

 

 

 

Page 112 Page 114
Image 113
Page 112 Page 114
Contents User Guide Important Notice Safety and Hazards Limitation Liability Qualcomm 3G Patents Copyright TrademarksContact Information Support@sierrawireless.comRevision Release Changes Number Date Revision HistoryContents Configuring your Raven Configuring Modbus/BSAP Contents Contents Contents Circuit Switch Communications Contents Connecting to the Internet Using DUN Aleos Introduction to the RavenAceManager AceWareMonitor and Control Simplified DeploymentNetwork Monitoring AceNetAceView Modem Doctor Setup WizardModem Doctor Modem Doctor USBSteps of a connection Connecting to the Sprint NetworkDynamic vs. Static IP Addresses Connecting to the InternetSecurity 1x CommunicationSpecifications Interface Port Pin-Outs Power ConnectorActivating your Raven on Sprint Network Setup WizardStarting the Setup Wizard Setup Wizard Connecting to the ModemSelecting Tasks Setup Wizard ConnectedAleos Update OptionalUpdate AleosActivate Modem Setup Wizard MSLSetup Wizard MDN and MIN/MSID Vision C3210 Setup Wizard Vision Configuration11 Setup Wizard Vision Home Agent IP Addresses Test Modem Setup13 Setup Wizard Connection Test Data Link Configuration14 Setup Wizard Data Link NAI 15 Setup Wizard Primary and Secondardy HA 17 Setup Wizard Passwords Optional Setting up a DUN Connection19 Setup Wizard DUN settings 21 Setup Wizard DUN settings Activating Using AT CommandsActivating the Modem Using AleosUsing Direct Commands to the Internal Hardware Data Link Indicator Lights Hardware Installation RavenConnecting to Power Indicator Lights Connecting to a Computer or other DeviceLight Patterns MountingOptional Mounting Bracket Hardware Installation of the Raven Rev 3.0B Feb.08 Hardware Installation of the Raven Rev 3.0B Feb.08 Start AceManager Configuring your RavenUsing AceManager AceManager Connect to Modem Connect to your RavenAceManager Connected Enter the configuration optionsCreating the Template with AceManager Using TemplatesWrite the changes to the modem · Cellular Technology specific settings the CDMA/EV‐DO group Applying a Template to one modem with AceManager Reset the modemConfiguring your Raven 10 AceNet Selected modems Choose a name and icon for your connection Using a Terminal Application with AT CommandsConnect To Port Settings serial only· Flow Control Hardware ConnectedAT Commands Serial Modes Data Communication and Host 6 ModesBasic Modes Data Communication Start up ModeBasic Modes AT Mode AceManager PassThru PassThru ModeSerial Modes Telnet ModeAT\APPP UDP Auto Answer UDP and UDP PadReliable UDP TCP and TCP Pad UDP Multicast ModeTCP Auto Answer Hybrid ModesUdplast Data Communication Public and Private ModeKeepalive Data usage using Keepalive Configuring KeepaliveIpping Reasons to contact the modem and/or the connected device IP ManagerUnderstanding Domain Names Car54.mydomain.com.ca Dynamic NamesCar54.mydomain.com AceManager Dynamic IP Using IP Manager with your RavenRestrictions for Modem Name Data Usage for IP Manager Server UpdatesEairlink.com Understanding DNS Configuring DNSAceManager DNS PPP-Peer Domain NameModbus Overview Configuring Modbus/BSAPTelemetry Remote Terminal Unit RTUProgrammable Logic Controller PLC Supervisory Control and Data Acquisition ScadaModbus TCP/IP Raven Modbus on UDPConfigure the listening/device ports Configuring the Raven at Polling Host for Modbus onConfigure IP addresses for the Modbus IDs Configure the default mode for start-upOptional Dynamic IP Address Configure the ports Configuring the Remote Ravens for Modbus with UDPAceManager UDP Configure IP addresses for the hostConfigure other RTU settings AceManager DNS Raven 20070914 Snmp Traps Snmp Simple Network Management ProtocolManagement Information Base MIB Security Level Snmp ConfigurationListening Port AceManager Change Password menu option User Name and PasswordCommunity String Snmp MIB Definition SampleTrap Destination Snmp Simple Network Management Protocol Snmp Simple Network Management Protocol Snmp Simple Network Management Protocol Display Responses Product ID Info information Configuration CommandsNETPHONE? DEVICEID?HOSTMODE? StatusNETCHAN? NETERR?Any other value Failure AT Commands Requiring PassThru mode +GSN +ECIO?+WHWV +WPRL?+++ CommonMisc Miscellaneous DS=n Dmethodd.d.d.d/ppppp or Dmethod@name/ pppppMethod= P UDP Method=T TCP Method=N Telnet OPRG=nS53=methodd.d.d.d/ppppp =1‐65535 D.d=IP address SerialS5=n S3=nS4=n =0‐255 =2‐10 seconds=1‐2545 Parity=O Odd Parity=E Even Parity=N None Parity=M Mark=tenths of a second S50=nS51=n S211=n\Qn \APPP+IPR=n $QCVAD=nModemhispeed CTSE=nNUMTOIP=n PPPNOCARRIER=nS7=n S0=n=seconds S60=n=interval =0 ‐MDhh HOR=nHh=01 Slip Hh=02 PPP Hh=03 UDP Hh=04 TCP Hh=33 BsapDU=n S83=nUALL=n UDPLAST=nDynamic IP DNSUPDATE=nD.d=IP address of domain server DNSUSER=d.d.d.dIPMGRKEYn=key DOMAIN=nameName=domain name MODEMNAME=name IPMGRUPDATEn=mPPP/Ethernet HOSTNETMASK=n.n.n.n DHCPSERVER=nHOSTAUTH=n D.d=local or peer IP address of the modem String=passwordPassThru \APASSTHRU String=AT commandsCSX1=n PTINIT=stringPTREFRESH=n RESETPERIOD=n=1‐255 minutes =1‐255 hours=SMS/E‐mail server number Pw= passwordEmail=email address Body=message body SMTPSTATUS?Subject=message subject Index= index list 0, 1 Message= message number CntsmsDasms SSMS? OtherDAE=n DATZ=n=15‐255 minutes ResetcfgD.d=IP address Name=domain name Name=domain name Port=port=1 On Host=IP address Port=TCP portFriends TELNETTIMEOUT=n=minutes TPORT=nD.d = IP address LoggingFM=n DBGCOMMLVL=n Telemetry/Addr ListDBGIPLVL=n DBGPPPLVL=nMVLEN=n IPL=nMVMSK=hh Hh=hex valueMVOPT=n Addr ListMVTYP=n RKEY=nId=ID D.d=IP address or name 1x/EV-DOHexid=ID D.d=IP address or name +CTA=nNnnnnn=6 digit unlock code ~NAMLCK=nnnnnnPROVISION=MSL,MDN/MIN,SID,NID PROVISION2=MSL,MDN,MIN,SID,NID+WIMI=num +WMDN=numNam=0 Min=phone number Msid=second number Sid=system ID Nid=network IDConfiguring Circuit-Switch Circuit Switch Communications BAT Commands and the Command String Commands Specific to the Raven 1x C3211 Commands Specific to the Raven 1x C3210 and C3216Common AT Commands Step by Step ConfigurationRaven LEDs in Circuit-Switched Mode Software Required Hardware RequiredInformation Required for CDMA/1x only Connect the modem to your computerErase the internal memory Rev 3.0B Feb.08 144 Start All Programs AirLink Communications AceManager 3G Activate the RavenSave the serial setting Configure serial port speed12 AceManager Disconnect Configure the Raven using a AceManager template15 AceManager Load Configure additional PassThru settingsConfigure the Raven for your equipment Save the configuration settingsReset the Raven Test the Raven ConfigurationCommission the Raven Modem on Site 151 20070914 Install the driver Installing a modem driver for RavenWindows Dial-up Networking C DUN Connect the RavenSelect the Modems tab Check Don’t detect my modem I will select it from a list Check Selected Ports Modem Properties Configure the driverModem Properties Modem Creating a Dial-Up Networking PPP Connection10 Windows Start menu Create a new network connectionSelect Connect to the Internet Select Set up my connection manually Rev 3.0B Feb.08 161 Rev 3.0B Feb.08 162 21 New Connection Finish Configure the DUN connectionCheck Show icon...when connected Rev 3.0B Feb.08 165 Select Advanced Start AceView Connecting to the Internet Using DUNWindows DUN Enable the ConnectionSelect Dial to connect to the modem and the cellular network Start the DUN sessionWindows Dial-up Networking DUN Rev 3.0B Feb.08 170
Related manuals
Manual 36 pages 19.88 Kb Manual 171 pages 23.08 Kb Manual 203 pages 17.49 Kb

20070914 specifications

Sierra Wireless 20070914 is a cutting-edge wireless communication module designed for IoT applications, offering remarkable features and robust performance. This module represents a significant advancement in the realm of embedded wireless solutions, catering to a variety of industries including automotive, industrial automation, and smart cities.

One of the key features of the Sierra Wireless 20070914 is its support for multiple cellular standards, including LTE, which ensures high-speed data transfer and reliable connectivity. The module is designed to operate on various frequency bands, making it versatile and suitable for global deployment. This multi-band capability allows businesses to deploy their IoT solutions in different regions without modification, reducing time-to-market and deployment costs.

Another standout characteristic of the Sierra Wireless 20070914 is its comprehensive and seamless integration with cloud services. The module supports advanced cloud connectivity options, enabling real-time data processing and analysis, which is crucial for industries that rely on timely decision-making. This feature is particularly important in sectors like transportation and logistics, where real-time tracking and monitoring are essential.

The power efficiency of the Sierra Wireless 20070914 is noteworthy. It is engineered to operate optimally in low-power modes, making it ideal for battery-operated devices. This focus on energy efficiency ensures prolonged device lifecycles, supporting the growing demand for sustainable and eco-friendly technologies.

Moreover, the module includes encrypted communication features, enhancing security and protecting sensitive data transmissions. With the increasing prevalence of cyber threats, this security aspect is critical for businesses looking to safeguard their IoT applications from unauthorized access and data breaches.

In addition to these features, the Sierra Wireless 20070914 offers comprehensive development support, including software development kits (SDKs) and application programming interfaces (APIs). This makes it easier for developers to integrate the module into their existing systems, streamlining the development process and accelerating innovation.

Overall, the Sierra Wireless 20070914 stands out as a powerful solution for IoT connectivity, blending advanced technology, security, and efficiency. Its capabilities are designed to support the diverse needs of modern industries, paving the way for future innovations and advancements in wireless communication. As businesses increasingly turn to IoT for modernization, modules like the Sierra Wireless 20070914 will play a crucial role in enabling this transformation.
Top Page Image Contents