Adjusting Bias

CHANGING LINE VOLTAGE RATING

The 9130 Amplifier is equipped with a simple means to adjust the AC line voltage rating for 100, 120 or 230 volts AC, 50/60 Hz. The configuration is labelled above the power cord connector. If the amplifier will be used in a location that requires a different line voltage, use the following procedure to change the configuration. Review the modification instructions before attempting this procedure. If any doubts exist about one’s ability to change the line voltage, it is advisable that the procedure be conducted by a qualified technician.

NOTE: Units wired for 230 VAC may be used over a range of 220 to 240 VAC. No compromise in safety or performance will result from operation within this range.

WARNING! UNPLUG THE UNIT FROM AC POWER BEFORE ATTEMPTING THIS PROCEDURE. FAILURE TO DO SO CAN RESULT IN SEVERE ELECTRICAL SHOCK.

1)Remove the top cover by removing the four hex head screws (two on each side).

2)Using the diagram “Component Layout” as a guide, find the white Voltage Selector plug on the printed circuit board located behind the front panel Power Switch. Note that this plug has several alternate positions. Each position is labelled for where the end of the plug is to be aligned for each appropriate voltage. Move this plug to the new desired position, making sure that the plug is fully seated on the mating pins.

3)Depending upon which new voltage is chosen, it may be necessary to change the AC line fuse. Locate the clip-mounted Line Fuse adjacent to the Voltage Selector plug. Replace the fuse with

a new slow-blow fuse as follows:

100 and 120 VAC: 5 amp

230 VAC:

2.5 amp

NOTE: For units wired at 100-120 VAC, the AC line fuse should be a 1/4 x 1-1/4” size, and approved by UL/CSA For units wired at 230 VAC, the fuse should be a 5 x 20mm size, and approved according to IEC 127.

4)Replace the cover.

5)Obtain a new voltage configuration label from the factory, and affix over the original markings on the rear panel. Alternately, prepare a small self-adhesive label and indicate the new voltage with

permanent ink. Relabelling the unit is a vital safety requirement, particularly if the amplifier is sold to a new owner.

The 9130 Amplifier employs a single control per channel to set the bias operating point of the output stage. This bias point is factory set, and normally should not require adjustment for the life of the product. However, should improper bias be suspected, or if repairs have been made that would require a readjustment of bias, the following procedure should be used. Review the instructions before attempting this procedure. If any doubts exist about one’s ability to set the bias, it is advisable that the procedure be conducted by a qualified technician.

WARNING! UNPLUG THE UNIT FROM AC POWER BEFORE ATTEMPTING THIS PROCEDURE. FAILURE TO DO SO CAN RESULT IN SEVERE ELECTRICAL SHOCK.

REQUIRED TEST EQUIPMENT: Milliammeter capable of measuring at least 130 mA.

1)Remove the top cover by removing the four hex head screws (two on each side).

2)Using the diagram “Component Layout” as a guide, find the fuses labelled Fl and F2 for the left channel, or Fl 01 and F102 for the right channel.

3)Working on one channel at a time, remove either one (and only one) of the fuses. Connect the

milliammeter to the two fuse clips, and set the meter to a scale capable of measuring at least 130 mA.

WARNING! THE NEXT STEP OF THIS PROCEDURE CAN EXPOSE THE OPERATOR TO UNINSULATED HIGH VOLTAGES. KEEP ALL BODY PARTS CLEAR OF THE INTERNAL CIRCUITRY OF THE AMPLIFIER.

-lO-

9130 specifications

The Hafler 9130 is a powerful and versatile two-channel power amplifier, designed to deliver exceptional audio performance for both professional and home audio applications. Known for its robust build quality and high-efficiency design, the Hafler 9130 is ideal for audiophiles and sound engineers who demand the best in sound reproduction.

One of the key features of the Hafler 9130 is its unique MOSFET output stage. This technology benefits sound reproduction by minimizing distortion while providing a smooth, natural tonal balance. The amplifier can produce a significant amount of power, offering up to 130 watts per channel into an 8-ohm load, and even more into 4 ohms. This capability ensures that the Hafler 9130 can drive a wide range of speakers, making it suitable for various audio setups.

In addition to its powerful performance, the Hafler 9130 integrates sophisticated circuit design, such as a high-quality balanced input stage. This feature allows for reduced noise and interference, resulting in a cleaner audio signal. The amplifier also incorporates a sophisticated thermal protection circuit, which automatically disconnects the output if the unit overheats, preventing damage and enhancing longevity.

Another prominent characteristic of the Hafler 9130 is its efficient heat dissipation system. Featuring large heat sinks and a well-ventilated chassis, the amplifier remains cool even during demanding playback situations. This design not only preserves the integrity of the components but also enhances the overall performance.

The Hafler 9130 is designed with an intuitive user interface, featuring recessed volume controls and a power switch that make operation straightforward. Additionally, the amplifier's versatile connectivity options include RCA and XLR inputs, allowing it to pair seamlessly with various audio sources.

Overall, the Hafler 9130 stands out as a reliable and high-performance amplifier. Its combination of advanced technologies, robust design, and user-friendly features make it a popular choice among enthusiasts and professionals alike. Whether used in a studio setting or a home theater, the Hafler 9130 delivers a powerful and dynamic audio experience that truly brings music and sound to life.