Emotiva manual Troubleshooting Guide, No Sound from one or more speakers connected to the XPA-1

Page 16

Troubleshooting Guide

The Emotiva XPA-1 is expertly designed and built to provide years of trouble-free performance. Most problems that occur can usually be solved by checking your setup or making sure that the audio and video components connected to the amplifier are on and fully operational.

The following information will help you deal with common setup problems you may experience during normal use of your unit. If problems persist, contact Emotiva for help.

No Sound (from one or more speakers connected to the XPA-1)

•Speaker cables may have come undone. Turn off your system and check the cables, and tighten the amplifier and speaker binding posts.

•Damaged audio cable.

•The preamplifier volume level is low for the channels concerned. Recheck the preamplifier calibration procedure.

•A preamplifier Mute switch may be on, or an external processor loop or a tape monitor loop is engaged.

•Check that your preamplifier or source is running the correct surround sound mode. Maybe it is set for 2-channel stereo when you were expecting 5.1 surround sound.

•Check in case any missing channels have been turned off in a preamplifier setup menu. For example, the center amplifier channel will not receive a signal if the preamplifier has been set to “Phantom.”

•If the unit is not on, the ON/OFFswitch on the XPA-1 might be in the off position.

•A internal fuse on the unit may have blown. Contact Emotiva for assistance.

The amplifier shuts down often or the line circuit breaker trips often

•Check that the positive and negative speaker wires are not shorted together.

•Make sure that no speakers are shorted internally. If you have an ohm-meter, disconnect the speaker wires and measure the resistance between the speaker’s positive and negative terminals. Measure all speakers and check their impedance speci fications. If necessary, review the “Series and Parallel Connections” section of this manual.

•If you have connected speakers in parallel, the overall impedance may be too low. It is recommended that you rearrange the speakers in series to increase the overall impedance, thus taking some of the load off the amplifier.

•Make sure that the amplifier has good ventilation and is not overheating. Allow good airflow underneath wherever possible. If the amplifier is in a closed rack, open up the rear panel or use a quiet fan for improved ventilation.

Poor Bass Performance from Full Range Speakers connected to XPA-1

•Make sure that your preamplifier does not have the bass (tone control) level turned down.

•Many surround preamplifiers have controls which can direct all the bass to subwoofers, or let your main speakers play the full range. Make sure that the preamplifier has been correctly set. If you are not using a subwoofer, set the speaker options to “Large” where possible.

Page 15

Page 15 Page 17
Image 16
Page 15 Page 17
Contents XPA-1 Table of Contents XPA-1 Technical Specifications Limited Warranty Safety Precautions Toll Free 877 EMO-TECH NEC National Electrical Code Standards Antenna Grounding Outside the HouseThank You for your XPA-1 Purchase Inventory Unpacking the XPA-1Recording the Serial Number Emotiva XPA-1 Reference Differential Amplifier Front Panel LayoutRear Panel Layout Remote Turn On JackAC Power Considerations Installation and ConnectionsPhysical Placement Output Connection Considerations Input Connection ConsiderationsConnection Tips for Superior Sound Connection Diagrams 12V Trigger ConnectionsSeries Series and Parallel Speaker ConnectionsParallel Technical Note about Multiple Speaker Connections Troubleshooting Guide No Sound from one or more speakers connected to the XPA-1Turn-on and turn-off thumps Hum Noises in the SpeakersOther Probable Causes of Noise Problems with the whole A/V SystemOne or more RED lights on the Front Panel are Blinking XPA-1 Technical Specifications Limited Warranty Emotiva Audio Corp Emotiva DisclosureEmotiva Audio Corp

XPA-1 specifications

The Emotiva XPA-1 is a powerful and sophisticated monoblock amplifier designed for audiophiles who demand high performance and exceptional sound quality. With a power output of 1000 watts per channel into 8 ohms, and doubling the power to 2000 watts into 4 ohms, the XPA-1 is engineered to drive even the most demanding speakers with ease.

One of the key features of the XPA-1 is its fully balanced design. This configuration minimizes distortion and improves dynamic range by reducing the noise floor, allowing for a cleaner and more detailed sound. The amplifier employs a Class A/B topology, ensuring that sound quality remains pristine while delivering the high power needed for demanding audio applications. This hybrid design combines the efficiency of Class B operation with the low distortion characteristics of Class A amplification.

Thermal management is another critical aspect of the XPA-1. The amplifier is equipped with a robust heat sink and thermal protection circuitry, ensuring that it operates safely and efficiently even during extended listening sessions. The design allows for quiet operation, minimizing the impact of fan noise, a common concern with high-power amplifiers.

The XPA-1 features high-quality components, including custom-wound toroidal transformers, which provide a stable power supply. This contributes to the amplifier's impressive transient response and dynamic capability, allowing it to handle complex musical passages and peak demands effortlessly. Additionally, the use of high-grade capacitors further enhances performance, ensuring that audio playback is not only powerful but also accurate and lifelike.

Another notable feature is the XPA-1's RCA and XLR inputs, providing versatile connectivity options for various audio sources. This enhanced flexibility allows users to integrate the amplifier seamlessly into their existing audio systems, whether for home theater setups or high-end stereo configurations.

Emotiva's attention to detail extends to the build quality of the XPA-1. With a sleek and sturdy chassis, the amplifier is designed to endure the rigors of everyday use while complementing any high-end audio environment. The front panel features a unified design with neatly arranged controls, making it user-friendly and aesthetically appealing.

In summary, the Emotiva XPA-1 is a high-performance monoblock amplifier that combines advanced technology, exceptional power output, and robust build quality. Its fully balanced design, powerful Class A/B amplification, and high-quality components make it an attractive option for audiophiles looking to elevate their sound systems to new heights. Whether for music or home theater applications, the XPA-1 delivers an uncompromising listening experience that truly captivates.
Top Page Image Contents