Spectra Logic T50E quick start Unpack Verify Components, Remove Shipping Key, Connect the Cables

Fibre Channel

Tape Drive Installation

1 Access bottom

2 Attach six feet

Spectra T50e Quick Start Guide

1

Unpack and

Verify the

Components

Install the Library

Power cord	Documentation		Half Height (HH) tape drive sled* -or- Full Height (FH) tape drive sled*	Rack-mount kit
		Documentation
Ethernet cable	Open This First
Rubber feet		USB drive
		(in kit)	* The tape drives, the (optional) redundant power supply, and the
			library may ship and arrive separately.

Rack-mount Installation Refer to the Spectra T50e Rack-mount Kit Installation Instructions supplied in the Spectra T50e Documentation Kit.

Tabletop Installation You do not need to remove the brackets.		Important! If you		remove the bracket, replace the
		black screw; do	not	replace the silver		screw.
Warning! The library weighs approximately 34.4 lb. Two people are
needed to move or lift the library.
German: Die Bebliothek hat ein Gewicht vonungefähr 15,6 kg. Zwei					1 Do not set
Personen ind notwendig, zu verschieben oder Aufhebung der Bibliothek.					the library on
Important! Lift the library only by the two sides—not by the front and back.					the bracket.
	Alignment
Do not stack items on top of the library, as they can restrict robot movement.			Bottom of library
	mark (6x)

1.Carefully place the library on its side, but do not damage the bracket.

2. Remove the paper backing from the six feet and install as shown. 3. Place the library on a level surface in a well ventilated location.

Note: Do not install the feet if you are rack-mounting the library.

Remove the

Shipping

Key

L

Shipping Key Removal Follow these steps to remove the shipping key:
		Important! Lift
1. Remove the tape securing the shipping key.		only by two sides.
2. Pull the key straight up and out of the library.	1	Remove tape
3. Place the tape back over the opening in the top of the library.
	2	Remove key
4. Store the key in the tab at the back of the library.
	3	Replace tape
	4	Store key

2

Install the Tape Drives

Install the tape drives from bottom to top.

1.Using a #2 Phillips screwdriver, remove the screws securing the cover plate (or plates), as needed. Important! Do not leave openings uncovered.

2.Remove the plate and store it and the screws for future use.

3.Remove the tape drive from its protective packaging.

4.While supporting the bottom of the drive sled, slide it into the empty drive bay. Push the drive sled in until it fits flush against the chassis and tighten the finger screws.

Note: Refer to the Spectra T50e Tape Drive Installation Instructions for additional information.

1 Remove screws

2Remove plate (remove two plates for each full-height tape drive)

3Remove tape drive from packaging

4Install tape drive Finger screws

4

3

2

Connect the Cables

SCSI Follow these steps to connect SCSI tape drives. Important! Do not mix full-height and half-height tape drives in the library. Do not daisy-chain LTO-4 SCSI tape drives.

1.Connect SCSI cables to the tape drives, as shown.

2.Terminate as follows:

ƒLTO-3—terminate if it is the last device on the SCSI bus. Every connector on an LTO-3 tape drive must either be connected to a host, connected to the next tape drive, or terminated. A maximum of two LTO-3 SCSI tape drives can be daisy-chained on a single SCSI bus.

ƒLTO-4—terminate the second connector on every tape drive. Do not daisy-chain LTO-4 tape drives.

3.Connect the other end of the cable to the host computer.

Follow these steps to connect FC tape drives.

1.Remove the protective plugs from the optical connector.

2.Insert one end of the cable into the tape drive (either port).

3.Connect the other end of the cable into the HBA or switch.

Note: See the Spectra T50e Library User Guide for information about dual-port tape drives.

Power Connect the power cord to the library and to an outlet.

Note: If you purchased an optional redundant power supply, refer to the Spectra T50e Power Supply Installation Instructions for information about installing it in the library.

Ethernet If you want to use the Ethernet option (remote management or email notification), connect the Ethernet cable to the library and to the host.

SCSI
Two half-height SCSI
tape drives shown.
2	Terminate
1	Connect SCSI
3	Connect to Host
Fibre Channel
1	Remove plugs
	P Power
2	Connect FC
3	Connect to Host
	or switch
	E Ethernet

•2009 Spectra Logic Corporation. All rights reserved worldwide. BlueScale, Spectra, SpectraGuard, TeraPack, and the Spectra Logic logo are registered trademarks of Spectra Logic Corporation. All other trademarks and registered trademarks are the property of their respective owners. Subject to change without notice.