Abit AN9 32X manual Troubleshooting How to Get Technical Support?, 1 Q & a

Page 51

5.2 Troubleshooting (How to Get Technical Support?)

5.2.1 Q & A

Q:Do I need to clear the CMOS before I use a new motherboard to assemble my new computer system?

A:Yes, we highly recommend that you clear the CMOS before installing a new motherboard. Please move the CMOS jumper from its default 1-2 position to 2-3 for a few seconds, and then back. When you boot up your system for the first time, follow the instructions in the user's manual to load the optimized defaults.

Q:If my system hangs when I update the BIOS or set the wrong CPU parameters, what should I do?

A:Whenever you update the BIOS or if the system hangs due to wrong CPU parameters setting, always clear CMOS jumper before booting up again.

Q: Why does the system fail to boot up again right after a mechanical power-off?

A: Please keep a 30-second interval between each mechanical power On/Off.

Q:Why does the system fail to boot up and nothing displays on the screen after I did some over-clocking or non-standard settings inside the BIOS?

A:It should not cause hardware or permanent damage to motherboard when BIOS settings were changed from default to over-clocking or non-standard status.

We suggest the following three troubleshooting methods to discharge CMOS data, recover the hardware default status, and then making the motherboard work again. There is no need to bother returning the motherboard to where you bought it from or go through an RMA process.

Step 1.Switch off the power supply unit and then switch it on again after one minute. If there is no power-switch on the power supply unit, disconnect its power cord for one minute and then reconnect.

Press and hold the <Insert> key on the keyboard, and press the power-on button to boot up system. If it works, release the <Insert> key and hit <Del> key to enter the BIOS setup page to apply the correct settings.

If the situation remains the same, repeat the procedures in Step 1 for three times, or try Step 2.

Step 2.Switch off the power supply unit or disconnect the power cord. Open the chassis cover. Locate the CCMOS jumper near the button battery. Change the jumper position from default 1-2 to 2-3 for one minute to discharge the CMOS data, and then put it back to default 1-2 position.

Close the chassis and switch on the power supply unit or plug in the power cord. Press the power-on button to boot up system. If it works, hit <Del> key to enter the BIOS setup page to do the correct settings.

If the situation remains the same, try Step 3.

Step 3.The same procedure as Step 2, but while discharging the CMOS data, pull out the ATX power connectors from motherboard and remove the button battery during CMOS discharge.

5-5

Appendix

Image 51
Contents Motherboard AMD Socket AM2 User’s ManualPage Contents Driver & Utility CD Appendix Fatal1ty IntroductionLIVIN’ Large CPU Features & SpecificationsFor more information Motherboard Layout For more information Choosing a Computer Chassis Installing MotherboardShort Open Checking Jumper SettingsCmos Memory Clearing Header and Backup Battery Page USB-PWR1 Wake-up HeadersATX Power Connectors Connecting Chassis ComponentsFront Panel Switches & Indicators Headers FAN Power Connectors CPU Socket AM2 Installing HardwareFor more information 2 DDR2 Memory Slots Page PCI Express X16 Add-on Slots Install Graphics Card Page For more information AudioMAX Connection Slot HD Audio AC’97 Audio MIC2 L Page Floppy and IDE Disk Drive Connectors Hardware Setup Connecting Peripheral DevicesSerial ATA Connectors Hardware Additional USB 2.0 Port HeadersAdditional IEEE1394 Port Headers PCI Express X1 Add-on Slots Hardware Setup PCI Add-on SlotsGuru Panel Connection Header Post Code Displayer Onboard Status DisplaySLIPWR1 Power Source IndicatorsConnecting I/O Devices For more information Bios Setup ΜGuru Utility OC GuruAbit EQ Advanced Bios Features Standard Cmos FeaturesIntegrated Peripherals Advanced Chipset FeaturesPnP/PCI Configurations Power Management SetupSave & Exit Setup Load Fail-Safe DefaultsLoad Optimized Defaults Set PasswordDriver & Utility CD For more information Award Post Code Definitions Post Code DefinitionsEarly PCI Initialization Auto 2 AC2005 Post Code Definitions 1 Q & a Troubleshooting How to Get Technical Support?Page Appendix Technical Support Form RMA Center http//rma.abit-usa.com Universal Abit Contact InformationJohnathan Fatal1ty Wendel