Avalon Acoustics OPUS Ceramique Loudspeaker manual Break-in Period

Page 13

4 Break-in Period

Your new Avalon Acoustics loudspeakers have an initial break-in period. They will not perform to their full sonic potential when first installed in your system. This is partially due to a residual polarization of the dielectric materials used in the crossover capacitors and internal wiring.1 As music is played through the loudspeakers, the electrical signal will gradually anneal these materials. Similarly, the suspensions of the drivers will reach their optimal mechanical properties as the speakers are played. Only after the break-in period will the full performance of your Avalon Acoustics loudspeakers be realized.

The break-in process will occur naturally as music is played through the system. To reduce the time required, it is recommended that the system be played continuously, using either a digital source in the repeat mode or an FM broadcast signal. The recommended break-in procedure is as follows:

•Initial warm-up: three to six hours of quiet music.

•Extended break-in: 200 to 300 hours of loud and dynamic source material (e.g. Tangerine Dream, Optical Race, RCA 2042-2-P).

During the break-in period, the sonic properties of your loudspeakers may undergo several gradual shifts as the various components break-in at different rates. It is therefore suggested that the fine-tuning of the system be delayed until after the break-in period is completed. However, during the final phases of the break-in period, the sonic image will open up, the sound-stage will gain specificity, the bass control and impact will increase, and the overall sound will have a more relaxed, involving presentation.

1A high-voltage test is applied to wiring and capacitors during their manufacture. This results in a residual polarization of the dielectric materials.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Music al Master piec es Page Table of Contents Features Introduction Unpacking Instructions ContentsIntroduction To unpack the loudspeakers Opening the CrateOrientation of the Felt Anti-Diffraction Mask Installing the GrillesInsertion of new grille pin into installation tool Replacing Grille PinsPage Connecting the Speaker to the Amplifier Wiring InstructionsDo not over-tighten the screws From Amplifier Break-in Period Maximizing Performance Speaker Placement and SymmetryGrille Assemblies Apex Couplers Toe-InCorner Treatment First Reflection PointsCare of Your Loudspeakers Grille AssemblyCabinet Hardwood Finish DriversEvent of a Problem WarrantyWarranty Statement Page Room AcousticsandSpeaker Position Basic Room Acoustics An Optical AnalogyStanding Waves Flutter Echo Early Reflections Avoiding Early Reflections Angle X Angle Y Reflected Sound DirectSound Bass reinforcement 100 200 500 Page Flutter Echo and Standing Waves Summary of RecommendationsEarly Reflections Speaker PlacementListening Room Example Accuracy of Bass Reproduction Fast Bass Sensitivity to Time-Related InformationAnechoic vs. In-Room Frequency Response RationaleCorrelation with Amplifier Measurements Measurements of Audio EquipmentLoudspeaker Measurements Designing for Accurate Bass Reproduction Listening for Size Distortions Frequency Response EffectsTransient Response Effects Conclusion Features Specifications

OPUS Ceramique Loudspeaker specifications

Avalon Acoustics is renowned in the high-end audio industry, and their OPUS Ceramique Loudspeaker exemplifies their dedication to exceptional sound quality and innovative design. This speaker is a perfect blend of artistry and advanced engineering, making it a coveted choice among audiophiles.

One of the key features of the OPUS Ceramique is its sophisticated driver configuration. It utilizes a three-way design, which is engineered to deliver a full spectrum of sound with impressive clarity. The loudspeaker is equipped with a 10-inch ceramic bass driver capable of deep, powerful low frequencies, ensuring that every note resonates with depth. Complementing this are dual midrange drivers made from advanced ceramic materials, which provide rich and warm mid tones. Finally, for the highs, the OPUS employs a unique ribbon tweeter designed for exceptional detail and an extended frequency response, offering a natural and airy sound that brings music to life.

The cabinet design of the OPUS Ceramique is as remarkable as its internal components. It features a rigid construction that minimizes resonance and cabinet coloration, ensuring that the sound remains pure and true to the source. The elegant curves of the speaker not only enhance its aesthetic appeal but also contribute to better acoustic performance by optimizing the dispersion of sound waves.

Another prominent technology incorporated in the OPUS Ceramique is its advanced crossover network. The crossover is meticulously engineered to ensure a seamless transition between the drivers, allowing for coherent sound reproduction across all frequencies. This means that listeners can enjoy an immersive soundstage where instruments and vocals are clearly delineated, creating a more engaging listening experience.

In addition to its acoustic prowess, the OPUS Ceramique is designed with the audiophile in mind. It is highly customizable, with various finishes available to suit any decor. The attention to detail extends to every aspect of its construction, providing both aesthetic beauty and functional performance.

Overall, the Avalon Acoustics OPUS Ceramique Loudspeaker stands as a testament to the brand's commitment to delivering extraordinary sound and elegance. With its innovative technologies and exceptional build quality, it continues to be a sought-after choice for discerning music lovers seeking the ultimate audio experience. Whether used in a dedicated listening room or as part of a high-end home theater system, the OPUS Ceramique promises to elevate any audio experience to new heights.
Top Page Image Contents