Dell 1537 manual Before You Begin, Recommended Tools Before Working Inside Your Computer

Page 3

Back to Contents Page

Before You Begin

Dell™ Studio 1535/1536/1537 Service Manual

Recommended Tools

Before Working Inside Your Computer

This document provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that:

You have performed the steps in Before Working Inside Your Computer.

You have read the safety information that shipped with your computer.

When replacing a component, you have already removed the original component, if installed.

Recommended Tools

The procedures in this document may require the following tools:

Small flat-blade screwdriver

Phillips screwdriver

Small plastic scribe

Flash BIOS update media (see the Dell Support website at support.dell.com)

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help ensure your own personal safety.

CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer.

NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty.

NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface, such as a connector on the back of the computer.

NOTICE: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.

NOTICE: When disconnecting a cable, pull on the cable's connector or on its strain-relief loop, not on the cable itself. For cable connectors with locking tabs, press inward on the locking tabs to release the connector. When connecting a cable, ensure that the connectors are correctly oriented and aligned to avoid damage to the connector and/or the connector's pins.

1.Ensure that the work surface is flat and clean to prevent the computer cover from being scratched.

2.Click Start , click the arrow , and then click Shut Down.

The computer turns off after the operating system shutdown process finishes.

3.Disconnect your computer and all attached devices from their electrical outlets.

NOTICE: To disconnect a network cable, first unplug the cable from your computer, and then unplug it from the network wall jack.

4.Disconnect any telephone or network cables from the computer.

5.Press and eject any installed cards from the ExpressCard slot and the 8-in-1 memory card reader.

NOTICE: To help prevent damage to the system board, you must remove the battery from the battery bay before you service the computer.

NOTICE: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for other Dell computers.

6.Turn the computer over.

7.Slide the battery release latch until it clicks into place.

8.Slide the battery out of the battery bay.

Image 3
Contents Model PP33L August 2008 Rev. A01 Base Cover Removing the Base CoverReplacing the Base Cover Recommended Tools Before Working Inside Your Computer Before You BeginBack to Contents Flashing the Bios Flashing the Bios From a CDFlashing the Bios From the Hard Drive Back to Contents USB/Audio Board Removing the USB/Audio BoardReplacing the USB/Audio Board Camera Removing the Camera ModuleReplacing the Camera Module Removing the Center Control Cover Center Control CoverReplacing the Center Control Cover Coin-Cell Battery Removing the Coin-Cell BatteryReplacing the Coin-Cell Battery Processor Module Removing the Processor ModuleReplacing the Processor Module Back to Contents Processor Thermal-Cooling Assembly Removing the Processor Thermal-Cooling AssemblyReplacing the Processor Thermal-Cooling Assembly Page Display Removing the Display AssemblyReplacing the Display Assembly Replacing the Display Bezel Removing the Display BezelRemoving the Display Panel Display PanelReplacing the Display Panel Removing the Display Inverter Replacing the Display InverterRemoving the Display Hinges Replacing the Display Hinges Removing the Hard Drive Hard DriveReplacing the Hard Drive Removing the Keyboard KeyboardReplacing the Keyboard Battery Latch Assembly Removing the Battery Latch AssemblyReplacing the Battery Latch Assembly Back to Contents Memory Removing Memory ModulesReplacing Memory Modules Back to Contents Microphone Removing the Microphone ModuleReplacing the Microphone Module Removing the Mini-Card Wireless Mini-CardWlan 2 or 3 antenna cables Replacing the Mini-CardBack to Contents Removing the Optical Drive Interposer Optical DriveRemoving the Optical Drive Replacing the Optical DriveOptical drive Optical drive interposer Removing the Palm Rest Palm RestReplacing the Palm Rest Speaker Assembly Removing the Speaker AssemblyReplacing the Speaker Assembly System Board Assembly Removing the System Board AssemblyReplacing the System Board Assembly Back to Contents Back to Contents