ADDITIONAL SETUP NOTES:
SPEED – AUTO
This setup option allows calibrating to a known mile or kilometer. By default, the speed is calibrated to use the Rhino Factory speed signal. Calibration should only be needed if the factory calibration is no longer correct due to changes to tires or gearing.
1.Start with vehicle at the beginning of the marked mile or kilometer and turn the key off.
2.Start engine while holding the left switch to enter setup.
3.Select speed option in setup and select appropriate unit (if you will be calculating to a known kilometer choose KPH, else choose MPH).
4.Select the Auto option. The gauge will light all the displays and the speed display will read
5.Begin driving the mile or kilometer. The message center will read the number of pulses read from the speed signal. This value cannot be used to determine if a mile or kilometer has been driven.
6.At the end of the mile or kilometer, stop the vehicle and press the right switch to save the new speed calibration. The gauge will return to the speed setup menu.
SPEED – ADJUST
This setup option allows adjustment to speed while driving. By default, the speed is calibrated to use the Rhino Factory speed signal. Calibration should only be needed if the factory calibration is no longer correct due to changes to tires or gearing.
1.Start vehicle while holding the left switch to enter setup.
2.Select speed option in setup and select appropriate unit (if you will be calculating to a known kilometer choose KPH, else choose MPH).
3.Select the ADJUST option. The gauge will light all the displays and the message center will read ADJUST
4.Follow another vehicle traveling at a constant known speed. Hold the left switch to begin increasing the speed reading. To decrease the speed reading, release the switch and press and hold the switch again.
5.The direction of adjustment will change each time the switch is released.
6.When the speed has been adjusted, press the right switch to save the new speed calibration. The gauge will return to the speed setup menu.
ODO/HR PRESET
Within the first 10 miles (16 km) and 1.0 engine hours after first installing the gauge, the option is available for a ONE TIME preset of the odometer and hour meter to the reading(s) of the previous gauge. If this option is not used within the first 10 miles (16 km) or 1.0 engine hours or an incorrect reading is saved, the gauge will need to be returned to Dakota Digital for any odometer/hour meter adjustment. The procedure to preset the meters is as follows:
1.If setting odometer select ST ODO option in setup. If setting hour meter select SET HR.
2.For odometer preset, verify that correct unit is displayed above message center. If not, turn key off to leave setup and use unit option under speed to set correct unit. NOTE: Preset MUST be done with correct unit or odometer will not be set correctly!
3.The current odometer / hour meter value is displayed with the first digit blinking
4.Press and release the left switch to change the digit. Press and release the right switch to move on to the next digit.
5.Repeat step 4 until all digits are set. After tenths digit is set, press and release the right switch.
6.Water temp display will read “”. Check the current unit (if in odo preset) and the odometer / hour meter value to make sure it is correct. If not, press and release the right switch to go back and make changes.
7.NOTE: Check the displayed odometer value VERY carefully before next step. After selecting yes, you will no longer be able to change the odometer / hour meter.
8.If the settings are all correct, press and release the left switch. Water temp display will read “”.
9.Press and release the right switch to preset the odometer / hour meter to the new value.
SERVICE METERS
This gauge has two service meters. These are a countdown hour meter and a countdown odometer. Both service meters can be disabled, or enabled independently. This allows for setting of two individual service points, one based on engine run time, the other based on odometer. This could also allow for setting a service point on whichever service point comes first, hourly or odometer.
When the setup point is reached, SERVICE DUE will scroll in the message center. Pressing either switch will clear the message until the next time the key is turned on. Once the service has been done, use the left switch to select the service meter that is due (display will show a negative value or zero). Press and hold the right switch to reset the service meter to the value set in setup.
The service meter can be disabled by selecting in setup. If a new value is set for the service meter, and the meter was previously set to OFF, the service message may immediately be displayed. Reset the service meter to begin a new countdown.
page 4 | MAN#650244:A |