SPEED |
|
| Speed gauge menu |
UNIT |
|
| Select unit for speed |
|
|
| Toggle between MPH and KPH (select unit to use for calibration) |
AUTO |
|
| Auto calibrate speed to a marked mile or kilometer |
|
|
| Pulls up all values on speed and speed pulses in odometer |
|
|
| Press Right switch to finish cal and save value |
ADJUST |
|
| Adjust speed cal while driving |
ADJUST |
|
| Each press of left switch toggles direction of adjustment, right switch to save and exit |
SRV MI (SRV KM) | Sets value of service odometer set when service odometer is reset | ||
OFF | ( | OFF) | Turns off the count down service odometer (default) |
500 | ( | 800) | Sets service to 500 mi or 800 km when resetting service odometer. |
…. |
|
| Service point can be set in 500 mi (800km) increments. |
7500 | (12000) | Sets service to 7500 mi or 12000 km when resetting service odometer. | |
MAIN |
|
| Returns to info menu |
TACH |
|
| Tachometer gauge menu |
UPDATE |
|
| Sets update rate for tachometer readout screen |
SLOW |
|
| tach updates at slowest rate (default) |
MEDIUM |
|
| fastest update on tach |
FAST |
|
| |
WARN |
|
| Sets RPM warning point (default 5500 RPM) |
W 2250 |
|
| Minimum warning point of 2250 RPM |
…. |
|
| Warning point can be set in 250 RPM increments |
W 9750 |
|
| Maximum warning point of 9750 RPM |
SRV HR |
|
| Sets service hour value used when resetting count down service hour meter |
OFF |
|
| Service hour meter disabled (default) |
10 |
|
| Minimum service hour set point |
… |
|
| Service hour reset point can be set in 10 hr increments |
310 |
|
| Maximum service hour set point |
MAIN |
|
| Returns to info menu |
GAUGES |
|
| Gauge option menu |
VLT HI |
|
| Set high voltage warning point (default 15.4V) |
VLT LO |
|
| Set low voltage warning point (default 11.1 V) |
OIL LO |
|
| Set low oil pressure warning point (default 9 PSI) |
WTR HI |
|
| Set high water temp warning point and set temperature unit (default 251F) |
DEG F (DEG C) | Select temp unit, press left switch to change, right switch to save | ||
WTR HI |
|
| Select high warning, left switch to change, right switch to save |
MAIN |
|
| Returns to info menu |
OPTION |
|
| Option menu |
DIM LV |
|
| Adjust dimming point on gauge |
OFF |
|
| Dimming function is off |
LVL 1 |
|
| Gauge will dim when light on gauge face is very low (default) |
… |
|
| 7 selectable dimming levels |
LVL 7 |
|
| Gauge will dim early when more light is on gauge face |
DM OUT |
|
| Enables/disables dim output for other gauges |
ON |
|
| Dim output will be high when gauge is dimming |
OFF |
|
| Dim output will be disabled (default) |
WN OUT |
|
| Selects which gauges provide a warn out signal on warn out wire (default all on) |
WN OUT |
|
| Gauges that provide signal out are lit up, left switch to change, right switch to save |
NO WRN |
|
| Warn output wire is disabled |
CLOCK± |
|
| Adjust clock speed for accuracy |
|
| Subtract 7 seconds from clock every 24 hrs | |
… |
|
| No adjustment to factory clock speed (default) |
0 SEC |
|
| |
… |
|
| Add seven seconds to clock every 24 hrs |
+7 SEC |
|
| |
ST ODO |
|
| Allows presetting of odometer value on initial install (not available after 10 miles / 16km) |
SET HR |
|
| Allows presetting of hour meter value on initial install (not available after 1.0 hrs) |
MAIN |
|
| Returns to info menu |
DONE |
|
| Leaves setup menu if selected |
page 3 | MAN#650244:A |