Microstar G52-MA00514 manual CPU Core Speed Derivation Procedure, Then

Page 16

Chapter 2

5. Connect the fan power cable from the mounted fan to the 3-pin fan power connector on the board.

fan power cable

CPU Core Speed Derivation Procedure

If	CPU Clock	=	100MHz
then	Core/Bus ratio	=	14
then	CPU core speed	=	Host Clock x Core/Bus ratio
		=	100MHzx14
		=	1.4GHz

Overclocking

This motherboard is designed to support overclocking.

However, please make sure your components are able to WARNING! tolerate such abnormal setting, while doing overclocking.

Any attempt to operate beyond product specifications is not recommended. We do not guarantee the damages or risks caused by inadequate operation or beyond product specifications.

2-4

Image 16

Contents MS-6547 v1.X ATX Mainboard Version G52-MA00514Voir LA Notice D’INSTALLATION Avant DE Raccorder AU Reseau FCC-B Radio Frequency Interference StatementCopyright Notice Revision Revision History Date V1.1 First release DecSafety Instructions Contents Bios Setup Glossary Getting Started Mainboard Specification Dimension AudioMounting OthersMainboard Layout Quick Components Guide JBAT1Hardware Setup CPU Installation Procedures Central Processing Unit CPUInstalling the CPU Fan CPU Core Speed Derivation Procedure ThenMemory Introduction to DDR SdramInstalling DDR Modules DDR Module CombinationATX 20-Pin Power Connector JWR1 Power SupplyATX 12V Power Connector JPW1 Mouse Connector JKBMS1 Back PanelKeyboard Connector JKBMS1 USB ConnectorsSerial Port Connector COM a & COM B Joystick/Midi ConnectorsAudio Port Connectors Stereo Audio ConnectorsParallel Port Connector LPT1 131Connectors Floppy Disk Drive Connector FDD1Hard Disk Connectors IDE1 & IDE2 TIPAux Line-In Connector JAUX1 CD-In Connector JCD1Modem-In Connector JMD1 Fan Power Connectors CPUFA/SYSFA Wake On Ring Connector JMDM1 IrDA Infrared Module Header JIR2Front Panel Connector JFP1 or JFP2 JFP1 JFP2Front PanelAudio Connector JP20 JP20Front USB Connector JUSB1 or JUSB3 Jumpers Clear Cmos Jumper JBAT1Slots AGP Accelerated Graphics Port SlotPCI Slots CNR Communication Network RiserPCI Interrupt Request Routing Bios Setup Entering Setup Control KeysGetting Help MainMenuSub-Menu General Help F1Main Menu Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit SetupTime Standard Cmos FeaturesIDE Primary/Secondary Master/Slave Access Mode Floppy 3 Mode SupportVideo Halt OnAdvanced Bios Features Quick Power On Self TestAnti-Virus Protection CPU L1 & L2 CacheFirst/Second/Third Boot Device Boot Other DeviceBoot Up Floppy Seek Boot Up NumLock StatusTypematic Rate Setting Typematic Delay MsecTypematic Rate Chars/Sec Security OptionHDD S.M.A.R.T. Capability Advanced Dram Control Advanced Chipset FeaturesSystem Performance Memory HoleAt 15M-16M CAS Latency SettingAGPAperture Size SiS OnChip IDE Device Integrated PeripheralsInternal PCI/IDE IDE Burst Mode IDE Primary/Secondary Master/Slave PIOPrimary/Secondary Master/Slave UltraDMA SiS OnChip PCI DeviceIDE HDD Block Mode SiS-7012 AC97 AudioSiS-7013 S/W Modem USB ControllerUart Mode Select IR Transmission DelayUse IR Pins Parallel Port ModeEPP Mode Select IDE/USB1/USB0/Audio Access InterfaceECPModeUseDMA Game PortAddress/Midi PortAddressIpca Function Power Management SetupAcpi Suspend Type Power Button Override Power/Sleep LEDVideo Off Option Video Off MethodPMWake Up Events AfterAC Power LostIRQ 3-7,9-15,NMI/IRQ 8 Break Suspend PowerUp byAlarm PNP/PCI Configurations Reset Configuration DataResource Controlled By IRQ ResourcesVGA Palette Snoop Bit Setting Action PCI/VGA Palette SnoopCPU Warning Temperature Shutdown TemperaturePC Health Status Chassis Intrusion DetectFrequency/Voltage Control CPU Clock RatioAuto Detect DIMM/PCI Clk Spread SpectrumCPU Host/SDRAM/PCI Clock Load Fail-Safe/Optimized Defaults Set Supervisor/User Password About Supervisor Password & User PasswordGlossary Dynamic RAM Dram Memory Technologies Ieee PS/2 Port