General features | Microsens 10/100Base-TX to 100Base-FX instruction

MICROSENS

1.General features

Installation and Operation Manual for

Mini Bridge 10/100Base-TX to 100Base-FX

with Link Through

Fig. 1 Main view

02.12.02 V01

The MICROSENS Fast Ethernet mini bridge permits the connection of two Fast Ethernet segments according to IEEE802.3u.

The bridge offers the conversion from full to half duplex, as well as the coupling of Ethernet to Fast Ethernet segments.

Thanks to the conversion into full duplex the limit of 412 m for a Fast Ethernet segment does no longer exist. With single mode fiber, it is possible to cover distances up to 125 km.

The10/100Base-TX port with autonegotiation permits the connection of 10Base-T and 100Base-TX devices and the self-learning filter function reduces the data traffic between the coupled segments.

Multiple LEDs show the status of the bridge and can be used for network diagnostics.

2.Getting started

Before you start installing the converter, check that the package contains the following items:

•The TP-Fiber bridge

•AC power supply or optional self powering cable (USB)

•This Installation manual

3.Power connection

TP-Fiber bridge with AC power supply

Please ensure that the selection switch for the power supply is on the left side (facing to the 5 V DC input, see. fig. 2).

Verify that the AC power supply conforms to your country AC power requirement and then insert the power connector. Afterwards connect the network cables.

TP-Fiber converter with self powering cable (USB, optional)

Please ensure that the switch for the power supply is on the right side (facing to the USB port, see fig.2).

Install the USB cable first, connector type A must be connected to the PC and connector type B to the bridge. Afterwards connect the network cables.

Warning: Please make sure that the power of PC/USB hub is turned on, otherwise the bridge will not work.

4.Configuration

Please configure the bridge with the DIP switches located at the side of the chassis (see fig. 4).

The following features can be configured:

Autonegotiation: With the switch 1 you can activate (AUTO) or deactivate (FORCE) the autonegotiation protocol on the copper port. When the autonegotiation is deactivated switches 2 and 3 port select the speed 10 or 100 Mbit/s and full or half duplex.

Link Through: Link Through can be selected with switch 4. Position LT means that Link Through is activated at position LT DIS means this feature is disabled (refer to chapter Link Through).

Duplex mode fiber port: Switch 5 selects the duplex mode of the fiber (100Base-FX) port. Position FDX is for full duplex and HDX for half duplex transmission.

Warning:

•When TP NWay port is connected to TP 100FDX (force mode) instead of NWay partner, it will result in 100HDX mode with invalid collision signal.

•Ensure that all network nodes are configured in an identical mode. Improper operation and flow control mode between TP and fiber port connections will render the LAN to work poorly.

Fig. 2 Power selector

5VDC

USB

5VDC

Fig. 3 Basic application

Fig. 4 Configuration switches

AUTO

100

FDX

1	2	3	4	5
FORCE	10	HDX	LT DIS	HDX
FORCE			LT DIS

	TP			TP

USB

MICROSENS reserves the right to make changes to products, without notice, to improve reliability, function or design.

MICROSENS GmbH & Co. KG - Kueferstr. 16 - D-59067 Hamm / Germany - Tel. +49 (0)2381/9452-0 - Fax -100 - www.microsens.com

10/100Base-TX to 100Base-FX specifications

Microsens, a leading provider of Ethernet switching and media conversion solutions, offers a highly effective and efficient media converter that bridges the gap between 10/100Base-TX (twisted pair) and 100Base-FX (fiber optic) networks. This essential device is designed for users who require seamless network integration, enhanced performance, and longevity in their infrastructure.

One of the primary features of the Microsens 10/100Base-TX to 100Base-FX media converter is its ability to convert electrical signals from copper cabling to optical signals over fiber. This allows for longer transmission distances, significantly reducing the issues related to attenuation and electromagnetic interference that are commonly experienced in copper-based systems. The 100Base-FX fiber connection enables data transmission distances of up to 2 kilometers when using multimode fiber cables, making it an ideal solution for expansive network environments.

Another key characteristic of the Microsens media converter is its support for both half-duplex and full-duplex operation. This versatility allows organizations to choose the appropriate mode based on their networking needs, whether for compatibility with legacy equipment or for enhanced data throughput in modern applications. The converter also automatically senses the speed of the incoming connection and adjusts accordingly, providing a hassle-free experience during integration.

In terms of technical specifications, the Microsens media converter is designed to be compact and efficient. It typically comes with LED indicators for monitoring power, link status, and data traffic, enabling quick diagnostics and troubleshooting. The converter is housed in a durable metal chassis that ensures longevity and durability, making it suitable for various deployment scenarios, including harsh environments.

Advanced features such as auto-negotiation, extensive network support, and compliance with industry standards further enhance the capabilities of the Microsens solution. The device supports an extensive temperature range, ensuring reliable operation in both indoor and outdoor settings.

Overall, the Microsens 10/100Base-TX to 100Base-FX media converter provides robust performance and reliability, making it a preferred choice for organizations looking to upgrade their networks without incurring significant costs. The combination of practicality, efficiency, and advanced technology positions this media converter as an invaluable tool for modern networking solutions.