Matsushita CF-30 service manual Setting the USB PCB and Antenna PCB

Page 46

9.2.13. Setting the USB PCB and Antenna PCB

The terminal of the antenna cable must not come in

contact with this terminal.

(Put it on the metal fittings side. )

Figure seen from direction of arrow of A

Insert the Plug into the Socket

A

Cable

Insert FPC into Relay Circuit Board Ass’ys socket

Relay Circuit Board Ass’y

Lock after FPC insertion

Mountain Fold (Straight Line)

Valley Fold (Dotted Line)

FPC

FIG

FPC

OK

(R0.51)

FPC

NG

The attention of folding : Breakage countermeasure. 1,The bending inside is R0.51

2,Don’t mistake a bending direction. Don’t use a mistaken thing.

9.2.13. Setting the USB PCB and Antenna PCB

1.Open the Connector Cover.

2.Fix the Antenna PCB using the 2 Screws. <N3>

3.Connect the 2 white Cables.

4.Fix the USB PCB using the Screws. <N5>

5.Connect the Cable to the Connector. (CN100)

6.Attach the Tape.

Screws <N3>: DRQT2+G6FKL

Screws <N5>: DRQT26+D4FKL

Tape

Connector

(CN100)

		<N5>
	USB PCB
	Antenna PCB
	Antenna Cable	Connector Cover
	(White)	Connector Cover	<N3>
	(White)		<N3>
			<N3>
	Antenna Cable
	(White)

9-24

Image 46

Contents Notebook Computer This is the Service Manual for the following areas E …for U.KModel No. CF-30 SERIES Model No. CF-30CTQAZ 1For U.K This apparatus must be earthed for your safety How to replace the fuseOpen the fuse compartment with a screw- driver and replace the fuse LASER SAFETY INFORMATION Page Page CONTENTS 1 Specifications Main SpecificationsBluetoothTM Only for model with Bluetooth Wireless LAN Only for model with wireless LAN23-E-1 2 Names and Functions of Part Q J H K L M N O P R C D E F GRight side 3 Block DiagramCF-30 Block Diagram Intel Core4 Diagnosis Procedure 4.1. Basic Procedures4.2. Troubleshooting Flow ChartError Diagnosis by Checking Beep Signal Sound 5 Power-On Self Test Boot CheckOutline of POST 6 List of Error Codes Only when the port replicator is connected 02F0 CPU ID 1-2. When you execute an automatic test 7 Self Diagnosis Test1. Beginning of self-diagnosis test 1-1. Setting of content of setup 1-3. When you execute the enhancing test2. Operation of PC-Diagnostic Utility 2-3. The content of the setup is returned to the setting of the user 2-2. PC-Diagnostic utility End method2-1. Selection of tested device Enhancing 7.1. Test Item and Division of troublePlace with possibili Test Item 8 Wiring Connection Diagram 9.1.2. Removing the Battery Pack and HDD 9 Disassembly/ReassemblyDisassembly Instructions 9.1.19.1.4. Removing the KB Cover, Hinge Cover L, Hinge Cover R and Key 9.1.3. Removing the HDDboard 9.1.5. Removing the KB Cable Cover and LCD Cable Cover 9.1.6. Removing the GPS PCB and Blue- tooth PCB9.1.7. Removing the DIMM Cover and Bot- tom Cover 9.1.8. Removing the USB PCB and Antenna PCB9.1.10. Removing the PAD PCB 9.1.9. Removing the FPC HDD BAT9.1.11. Removing the Main PCB CN400,CN401 11. Remove the 2 Screws. N5 12. Remove the 2 Screws. N21 and PCMCIA Card 9.1.12. Removing the SD PCB, Express Card9.1.13. Removing the I/O PCB 1. Open the Connector Cover and Lid Cover9.1.15. Removing the Handle and Power SW 9.1.17. Removing the LCD Rear Cabinet 9.1.16. Removing the Display UnitHinge L and R 9.1.18. Removing the Inverter PCB, TS PCB and LCD Unit 9.1.19. Removing the Antenna PCB L and R9.2.2. Setting the Antenna PCB L and R 9.2. Reassembly Instructions9.2.1. Attention when CF-30 series is repaired Safety Working9.2.3. Setting the Inverter PCB, TS PCB and LCD Unit Inverter-PCB9.2.4. Setting the LCD Rear Cabinet, Hinge L and R 9.2.5. Setting the Display Unit 9.2.6. Setting the Handle and Power SWSW-LED FPC Ass’y Attach the TapeAttach the Sheet Attach it not to overlap the SW leg9-16 Q Assembly of Power SWQ Assembly of Palm Top Cover Cover9.2.8 Setting the I/O PCBSetting the SD PCB, Express Card 9.2.99.2.10. Setting the Main PCB 24. Fix the Screw. N7 25. Attach the TOP Screws N7 Connector CN17Connector CN27 9-1912 Safety Working Q Assembly of LAN, Modem and MDCQ Assembly of Main PCB 9-209.2.11. Setting the PAD PCB 9.2.12. Setting the FPC HDD BAT Page 9.2.13. Setting the USB PCB and Antenna PCB Q Assembly of USB PCB and Antenna PCB 9-259.2.14. Setting the DIMM Cover and Bottom Cover 9-27 Q Preparation of DIMM CoverAttach the Keyboard Cable Cover Cushion 2. Connect the Cable to the Connector on GPS PCB 9.2.15. Setting the GPS PCB and Bluetooth PCB1. Fix the GPS BT Angle and GPS PCB using the 2 Screws. N11 3. Fix the GPS Ass’y using the 4 Screws. N129.2.16. Setting the KB Cable Cover, Keyboard and LCD Cable Cover to Connector7.2.18. Setting the HDD Q Preparation oh HDD ASSY Lead WireImportant Parts Heater for Safety 9-31Push and bend 1. Apply the load when attaching the parts. 20N to 30N 2 to 3Kgf/cm2HDD Damper Ass’y HDD Ass’yDo not bend it at a sharp angle to put natural R HDD Thermal PlateKeep the space to secure the air vent A-A SEC HDD Side DamperB-B SEC Lower CaseAvoid getting HDD under the side damper when inserting HDD 1. Set the HDD Pack 2. Set the Battery Pack 9.2.19. Setting the Battery Pack and HDD Pack9-36 10 E xploded View Screw tightening torqueQ 0.22 ± 0.02 N.m 2.2 ± 0.2 kgf.cm R 0.30 ± 0.05 N.m 3.0 ± 0.5 kgf.cm A 0.19 ± 0.02 N.m 2.0 ± 0.2 kgf.cm B 0.45 ± 0.05 N.m 4.5 ± 0.5 kgf.cmG 1.47 ± 0.20 N.m 15.0 ± 2.0 kgf.cm L 0.2 ± 0.02 N.m 2.0 ± 0.2kgf.cm T 0.90 ± 0.05 N.m 9.0 ± 0.5 kgf.cmScrew tightening torque 10-4 B 0.45 + 0.05 N.m 4.5 + 0.5 kgf.cm P 0.8 + 0.1N.m 8.0 + 1.0 kgf.cmR 0.3 + 0.05 N.m 3.0 + 0.5 kgf.cm S 0.19 + 0.05 N.m 2.0 + 0.5 kgf.cm K2-32K10-2 K9-1-4A E35-10 E35-5E35 K54 E35-2 E15 K56 E35-3E35-1 E35-8 E35-4 E35-6 E35-3 E35-7 E35-4 A E35-10 E35-9Screw tightening torque CF-30CTQAZxx Replacement Parts ListREF. NO and AREA Mechanical Parts AccessoriesPacking Material FAX +44-029-20736250K2-2-4 WIRELESS SW CASEWIRELESS SW KNOB DFHR6257ZAK2-10-4 POWER SW CUSHIONWIRELESS SW FPC DFHR3E58ZATOUCH SCREEN PANEL KIT K9-2DFWV84A0277 K9-2-1INV SHIELD CASE POWER SW LED PANELDFMC0863ZA DFMC0873ZASERIAL COVER PLATE K122DFMD4067ZA-0 K123Note Important Safety Notice Replacement Parts List11-8 11-9 F1G1A104A014D 8, 9, 10, 11, 12, 13, 14 11-10IC 32, 58, 59, 61, 62, 68 Q 1, 2, 36, 52, 53, 59, 66 11-11IC 65, 72, 96, 101, 102 Q 3, 4, 16, 30, 31, 32, 33R 40, 104, 109, 136, 150 11-12R 21, 47, 99, 100, 101 R 49, 117, 151, 152, 20911-13 R 170MP PCB IO PCB11-14 BAT FPC SD PCBP-SW PCB HDD PACK PCBBLUETOOTH PCB 11-16