Matsushita CF-T4GWCTZ1 2 service manual Reassenbly instructions, Assembly knowhow of part LCD

Page 17

3 Reassenbly instructions

3.1.Attention when CF-T4G series is repaired

·Please execute writing BIOS ID when you exchange the main board.

·Parts (sheet and rubber) etc. related various the conductive cloth and heat spreader cannot be recycled. Use new parts.

3.2.Assembly knowhow of part LCD

LCD rubber, LCD side rubber and LCD backing rubber’s putting

LCD Rubber (Upper

 

LCD Rubber(Upper)

LCD Side Rubber

 

LCD Front Case

LCD Back Rubber(Lower)

Big Small

 

 

 

LCD Front Case

LCD cable processing

Clamping processing of LCD cable, LCD connector connection and putting of PET tape of cable 12mm

The LCD insulation sheet is peeled off.

PET Tape

 

The LCD cable is processed to the LCD frame clamping.

 

 

 

The LCD cable is connected with the connector.

 

 

The PET tape is put.

1

2mm

 

LCD Insulation Sheet

 

 

Be parallel after putting

Connector

LCD Frame Clamp

A red line of the cable is matched to the LCD frame externals.

 

 

 

0

1mm

Putting of the conductive cloth

 

 

 

 

The conductive cloth is put and after putting a both side tape is put.

 

Insulation Sheet of edge match

Process the part in the Signal line of the LCD cable in the conductive cloth.

0

1mm

 

Put the conductive cloth on the connector surely.

 

 

 

Conductive Cloth

 

 

 

 

 

 

 

 

(LCD Label)

Connector of externals match

Connector

 

 

 

There must not be beginning to see from externals.

 

 

 

 

 

 

 

 

Both Side Tape

 

 

LCD Cable

LCD Insulation Sheet

 

 

 

3-1

Image 17
Contents CF-T4 Page Page Page Page Page Page Connection Diagram Disassembly Flow Chart Disassembly instructionsRemoving the Keyboard DisassemblyPreparation Removing the Top Case Removing the HDDHDD HDD FFCPAD FFC Removing the Touch PadRemoving the USB Board Removing the LCD Knob and the SpeakerRemoving the Main Board Removing the Antenna Board L,R and the DC-IN Cable Removing the Wireless LAN ModuleDC-IN LANRemoving the Card Bus Ejector Removing the ModemRemoving the LCD Unit and the LCD Rear Removing the LCD UnitRemoving the Hinge Cover Remove the InverterReassenbly instructions Assembly knowhow of part LCDRear Damper Putting of conductive cloth of LCD cable 75 5mm Assembly of Touch Pad Installation and Line processing of SpeakerProcessing of Modem Cable and LAN Cable Processing of DC-IN Cable and Coaxial CableObtaining of Side Cover L Processing of USB Cable Screw tightening procedure of Each UnitScrewB ScrewC ScrewB Display Section Exploded ViewLCD Unit Assy / Pen Holder Section Cabinet Section JK2 Bottom SectionReplacement Parts List DFBH3042ZA HINGE-R TP DFMY3192ZA Heat Spreader Bottom EEFCD0D151ER Replacement Parts ListPage Page Page Page EEFUD0D331ER EEFCD0D101ER EEFSX0D271EREEFUD0E221ER DCUM1A1051BDERJ2GEJ103X RESISTOR, 1/16W, 10KΩ ECJ2FF1A106ZEEFUD0J101ER EEFUD0G151ER ConnectorThermistor DiodeFUSE, 2A DEDRB081L20 DiodeFUSE, 1A IC, CPUIC, Clock Generator IC, USB Power ControlIC, PC-CARD SW IC, RegulatorInductor IC, LinerInductor DDB5Z024E-L Inductor DDB5Z024C-L DDB5Z032A-L DDB5Z021C-YTransistor Poly SWTransistor ERJ2GEJ681X B1GFCFEN0003 Transistor DETA144EETLERJ2RKF27R4X ERJ2GEJ151XERJ2GEJ750X ERJ3GEYJ100VERJ2RKF2210X ERJ2RKF1000XERJ2GEJ103X RESISTOR, 1/16W ERJ2RKF80R6X RESISTOR, 1/16WERJ2GEJ222X ERJ2RKF1002X RESISTOR, 1/16W, 10KΩ ERJ2RKF75R0X ERJ2GEJ101XResistor Array ERJ2RKF1501X ERJ2GEJ390XERJ3GEYJ2R2V ERJ2GEJ220XERJ2GEJ102X RESISTOR, 1/16W, 1KΩ ERJ2GEJ120X ERJ2RKF49R9XERJ2GEJ330X ERJ2RKF4750XERJ2GEJ203X RESISTOR, 1/16W, 20KΩ ERJ2RKF22R6XERJ2GEJ106X RESISTOR, 1/16W, 10MΩ ERJ2GEJ105X RESISTOR, 1/16W, 1MΩFilter ERJ2GEJ473X RESISTOR, 1/16W, 47KΩERJ2GEJ472X ERJ2GEJ100XERJ2RKF3901X ERJ2GEJ471XERJ2RHD103X RESISTOR, 1/16W, 10KΩ ERJ2GEJ561XERJ2RKF1003X ERJ2RHD333X RESISTOR, 1/16W, 33KΩERJ2RHD222X ERJ2RKF5102X RESISTOR, 1/16W, 51KΩEEFUD0J151ER TranceDRHM0100ZA Spacer DRHM0099ZA DEARA8AJ473M Resistor Array ERJ2GEJ822XERJ2GEJ270X ERJ2GEJ152X