Speaker, Line | Yorkville Sound ES200P specs

POWER

SUBWOOFER

LEVEL

+3 +10

0 +20

-3

INPUT GROUND

-6 dB +25

ES200P

DESIGNED & MANUFACTURED BY YORKVILLE SOUND • TORONTO, CANADA

230V		120V
50Hz		60Hz
1.1A	Yorkville	2.2A

CAUTION: REPLACE WITH

SAME TYPE FUSE AND RATING

ATTENTION: UTILISER UN FUSIBLE DE

RECHANGE DE MEME TYPE ET CALIBRE

T 1,25A L

GROUNDED

UNGROUNDED

INPUT LEVEL

SPEAKER

LINE

I N P U T

PARALLEL

THRU

POWER

INTRODUCTION

The ES200P powered subwoofer incorporates a 200 watt amplifier. It can be used to enhance the bottom end (bass) of a full-range speaker system and increase the overall output of the system. The inputs to the subwoofer can accept a single source either from a speaker/amplifier output or a line level output from a pre-amp or mixer.

The ES200P also has a built in limiter and thermal protection that make this product

smooth and robust at high power levels. The internal limiter and the internal protection are factory set to maximize performance.

1.Power Switch

2.Volume

Set the volume control to a desired level as music is being played through the unit.

A setting of 0 dB on the SUBWOOFER LEVEL control is the correct starting point when setting up a sound system. From there the sound can be adjusted for best sound. The 0 dB mark refers to the setting that will give full power when the line input is used and the input signal is at a level of +4 dBV. This also is the setting to give a sensitivity of 2.83 Vrms (1 watt 8- ohms) for 100 dB spl when set for speaker level input. With a typical full range companion speaker this will give flat response. In either line or speaker operation it will usually be desireable to set the control at +3 to +6 to give some bass boost at low power levels. At levels approaching full power the built-in limiter will automatically reduce the gain to prevent over powering the subwoofer. Operation with settings significantly above +12 may clip the circuitry in the subwoofer reducing the dynamics of the music. Setting the subwoofer gain above +12 is only appropiate at low operating levels.

3. Input Level Switch

Speaker

Normally, the input to the subwoofer is from a full-range speaker cabinet, or amplifier output.

(See figure 2.0)

Line

In this case, the input to the subwoofer is from a line level source such as a mixer.

4. Ground Lift

If a hum, or buzz is detected from the subwoofer, try setting the switch to the GND LIFT position (OUT position). The switch should otherwise be left in the GND (IN position).

5. Input Jacks

The two inputs are balanced 1/4-inch parallel jacks and can be connected as shown in figures 2 and 3, on the following page. Please note that there is no effect to the performance of the full-range speaker if it is used to supply a music signal to the ES200P.

ES200P specifications

The Yorkville Sound ES200P is a powerful and versatile portable PA (public address) speaker system that is designed to meet the needs of both professionals and casual users. Renowned for its impressive sound quality and robust build, the ES200P is an excellent option for a variety of applications, including live music performances, public speaking events, and even small gatherings.

One of the standout features of the ES200P is its integrated 2000-watt amplifier, which delivers clear, crisp audio with deep bass response. This level of power ensures that the sound can fill a large room or outdoor space without distortion, making it a reliable choice for any event. The speaker is crafted with advanced technologies, including a high-quality polypropylene cabinet that enhances durability while controlling resonance, resulting in a precise audio experience.

The ES200P also boasts a 15-inch woofer and a 1-inch tweeter, designed to reproduce both low and high frequencies with clarity. This combination allows for a rich sound profile, ensuring that vocals remain clear while instruments retain their full-bodied character. Its frequency response range further enhances its versatility, making it suitable for a wide range of audio applications.

Another notable feature of the ES200P is its built-in digital mixer, which supports multiple channels and offers onboard effects, allowing users to customize their sound easily. The mixer includes various inputs, including XLR, TRS, and RCA connections, enabling musicians and presenters to connect various devices seamlessly. This level of connectivity ensures that the ES200P can integrate into different setups, whether used with microphones, instruments, or playback devices.

For ease of transport and setup, the ES200P is designed with a lightweight structure, complemented by ergonomic handles. This portability makes it an appealing option for traveling performers or events that require quick deployment. Additionally, the speaker's rugged design ensures it can withstand the rigors of transport, making it ideal for regular usage.

In summary, the Yorkville Sound ES200P stands out in the crowded PA speaker market due to its powerful amplification, high-quality sound reproduction, user-friendly mixer, and portable design. Whether for professional use or personal enjoyment, the ES200P promises reliability and performance, making it a valuable addition to any audio toolkit.