Minuteman UPS PN-34000247 user manual Installation, Operation, Battery Replacement

Page 1

ParaShield 1224

User’s Manual

ParaShield 1224 is designed to provide a local power solution for cable telephony, wireless local loop (WLL), and fiber to the home (FTTH) broadband equipment.

IMPORTANT SAFETY WARNINGS (SAVE THESE INSTRUCTIONS)

This manual contains important instructions regarding the installation and operation of this device. Read this manual thoroughly before attempting to unpack, install or operate this device

CAUTION! The battery can energize hazardous live parts inside even when the AC input power is disconnected.

CAUTION! To reduce the risk of electric shock, do not remove the cover, except to service the battery. No user serviceable parts inside, except for the battery.

CAUTION! To avoid electric shock, turn off the unit and unplug it from the AC power source before servicing the battery or installing your equipment.

INSTALLATION

(QUALIFIED SERVICE PERSONNEL ONLY)

Please read this manual before installing this DC UPS as it provides important information that should be followed during the installation and repair of the DC UPS:

1.) The ParaShield 1224 is intended to be installed in a temperature controlled environment that is free of conductive contaminants. Select a location which will provide good air circulation for the DC UPS at all times. Avoid locations near heating devices, water or excessive humidity, or where the DC UPS is exposed to direct sunlight. Route power cords so they cannot be walked on or damaged.

2.) Remove the cover.

3.) Remove the battery.

4.) The wall mount screws must be the appropriate size for total weight of the UPS and the mounting structural material.

5.) Connect the battery negative (Black) wire to the battery negative terminal.

6.) Connect the battery positive (Red) wire to the battery positive terminal.

7.) Re-install the battery into the case.

8.) Connect the output wires and connector to the DC UPS.

9.) Connect the Communications Signal wires to the DC UPS.

10.) Re-install the cover.

11.) See the section “Operation” for the startup procedure.

OPERATION

1.) Plug the DC UPS power cord into the AC inlet on the DC UPS.

2.) Plug the DC UPS power cord into the wall outlet.

3.) Turn on the connected equipment.

4.) The DC UPS is ready for normal operation.

The DC UPS charges the battery when it is connected to utility power. It is recommended that the battery charge for minimum of 18 hours before use. The DC UPS may be used immediately, however, the “On Battery“ runtime may be less than normally

expected.

BATTERY REPLACEMENT

(QUALIFIED SERVICE PERSONNEL ONLY)

This DC UPS has a hot-swappable battery. Hot-swappable battery means that the battery can be replaced without powering down the whole DC UPS system.

If there is a power interruption while replacing the hot-swappable battery, with the DC UPS on, the load will not be backed up.

CAUTION! Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes and may be toxic.

Do not dispose of batteries in a fire. The batteries may explode. The batteries in this UPS are recyclable. Dispose of the batteries properly. The batteries contain lead and pose a hazard to the environment and human health if not disposed of properly. Refer to local codes for proper disposal requirements or return the battery to MINUTEMAN in the packing material for the new battery.

CAUTION! Although battery system voltages are only 12VDC the battery system can still present a risk of electrical shock. The current capability of a battery is sufficient to burn wire or tools very rapidly, producing molten metal. Observe these precautions when replacing batteries:

1.) Remove watches, rings, or other metal objects.

2.) Use hand tools with insulated handles.

3.) Wear protective eye gear (goggles), rubber gloves and boots.

4.) Do not lay tools or other metal parts on the top of the batteries.

5.) Disconnect the charging source before connecting or disconnecting the battery terminals.

6.) Determine if the battery is inadvertently grounded. If the battery is, remove the source of the grounding. Contact with any part of a grounded battery can result in an electrical shock. The likelihood of such shock will be reduced, if such grounds are removed during installation and maintenance.

Step 4. Connect the black cable to the battery negative terminal on the new battery.

Step 5. Connect the red cable to the battery positive terminal on the new battery.

Step 6. Install the new battery into the battery compartment. Step 7. Tighten the battery stripe to secure the battery. Step 8. Re-install the battery cover.

Step 9. The DC UPS is ready for normal operation. Step 10. Dispose of the old battery properly.

Warning Indicator

●Front Panel

Indicator

Color

Condition

 

 

 

 

Green

DC UPS is on utility power.

 

 

 

 

Yellow

DC UPS is on battery power.

 

 

 

 

Green

DC output power is provided by the battery or

 

 

utility power.

 

 

 

 

Red

The battery is not connected or the battery needs

 

 

to be replaced.

 

 

 

PN-34000247 Rev0

Page 1 Page 2
Image 1
Page 1 Page 2
Contents Battery Replacement InstallationQualified Service Personnel only Indicator Color ConditionSpecification Communication SignalsLimited Warranty Cold Start

PN-34000247 specifications

The Minuteman UPS PN-34000247 is a reliable uninterruptible power supply designed to protect sensitive electronics and critical systems from power disturbances. With a focus on providing uninterrupted power, the Minuteman UPS employs a range of advanced technologies and features to ensure the safety and efficiency of connected devices.

One of the standout features of the PN-34000247 is its robust battery management system. The UPS is equipped with a high-performance lead-acid battery that provides ample backup power during outages. This ensures that connected equipment continues to function seamlessly even in the event of a power failure. The intelligent battery management system also monitors battery health, providing alerts for maintenance and ensuring optimal performance.

The Minuteman UPS PN-34000247 incorporates advanced surge protection technology. This feature safeguards sensitive electronics from power surges and spikes, which can cause irreparable damage. The device includes multiple outlets, allowing users to connect several devices while maintaining surge protection across all of them.

Another key characteristic of the Minuteman UPS is its ability to provide automatic voltage regulation (AVR). This technology helps to stabilize voltage levels, ensuring that connected devices receive a consistent power supply. Fluctuations in voltage can lead to system malfunctions or failures, and the AVR feature minimizes these risks by correcting low or high voltage inputs automatically.

The UPS also features an LCD display that provides real-time data on power conditions. Users can monitor battery status, load levels, and input/output voltages, allowing for informed decision-making regarding power management. This transparency helps users understand the operational status of their UPS and take necessary actions in case of abnormalities.

Furthermore, the Minuteman UPS PN-34000247 offers various communication options. It can be integrated with network management systems, enabling remote monitoring and management of power conditions. This is particularly advantageous for businesses that need to maintain critical systems with minimal downtime.

Designed with energy efficiency in mind, the Minuteman UPS adheres to modern energy standards, reducing its impact on the environment while saving on electricity costs. With its compact footprint and reliable performance, the PN-34000247 is an ideal solution for small businesses, home offices, and other settings where power continuity is essential.

In summary, the Minuteman UPS PN-34000247 combines advanced technologies and features such as intelligent battery management, automatic voltage regulation, surge protection, and real-time monitoring to provide top-notch power management solutions. Its design caters to users’ needs for reliability, efficiency, and ease of use, making it a valuable addition to any power-sensitive environment.
Top Page Image Contents