Connecting the Speakers

The CS.5’s input terminals are located on the back of the speaker at the base. For proper performance, it is essential that both speakers in a stereo system be wired in the same polarity. The speaker’s input terminals are color coded to facilitate this. The wire connected to the red input terminal of each speaker should connect to the respective positive output terminals of the amplifier; the wire connected to the black input terminal of each speaker should be connected to the respective negative output terminals of the amplifier. Make sure that all connections are tight.

The speakers should be connected to the amplifier with high quality cable to insure minimal loss of power and proper control by the amplifier. If the speakers are being connected to a vacuum tube amplifier with various impedance taps, the 4 ohm tap will probably give the best results.

If the amplifier has a speaker fuse or if a fuse is used in line to the speakers, we recommend a value of 2 amps of the normal blow type (type 3AG-2 amp). Although fuses offer some protection, they do not necessarily protect the speaker against all types of overload and also introduce audible degradation of the signal.

Due to European CE regulations that do not permit banana plug type loudspeaker connections, we ship THIEL speakers with removable plugs installed in the ends of the binding posts. If you wish to use banana plug type connections, you may remove the plastic plug inserted into the end of each plastic binding post cap. To remove the plugs, completely remove the two post caps by turning them counter-clockwise with a 1⁄2-inch nut driver or wrench until the caps come off the threaded post. Using a small screwdriver or similar tool, push the plug out from the bottom of the cap. Reinstall the plastic caps on the threaded posts. (Note: You may wish to modify the plastic binding posts caps one at a time to insure that the properly colored cap is reinstalled on the correct post.)

STABILIZER PINS

Speakers positioned on a soft surface such as carpeting are able to rock back and forth slightly and will vibrate in reaction to those forces the speaker generates to move the driver diaphragms. (Every action has an equal and opposite reaction.) This motion of the speaker causes a loss of musical information and reduces the clarity of the music.

In order to eliminate this effect, the THIEL CS.5 can be used with the provided stabilizer pins. The stabilizer pins are pushed into three sockets in the base of each speaker. The pin point penetrates the carpet and allows the speaker to rest firmly on the floor. The three pins provide a stable foundation which eliminates some obscuring of information and produces a cleaner, more articulate sound. No pins are required when placing the speakers on hard or smooth surfaces.

There are some applications where the stabilizer pins will not bring an improvement in sound but may actually make it worse. This situation occurs when the floor itself is not rigid and therefore vibrates when connected to the speakers via the stabilizer pins. We encourage you to experiment to determine for yourself whether or not this is the case.

To insert the pins, tilt the speaker forward and push the two back pins fully into the 1" deep holes located in each back corner of the base. Then rock the speaker backward and insert the front pin. Finally, press firmly on the top of the speaker with a slight rocking motion until the pins penetrate the carpet completely. To check that the pins are firmly seated, lightly tap the back and side of the speaker. There should be no movement and the speaker should feel solidly in place.

If the speaker is moved with the pins in place, care should be taken to lift the speaker straight upward until all the pins have cleared the carpet. Also, tilting the speaker so its weight is resting on any single pin can damage the speaker’s wood base.

Please be cautioned that the pointed pins can be dangerous if not used with care. They can cause small dents in hardwood floors and it is possible to damage carpets if the speakers are moved incorrectly with the pins in place.

ASSOCIATED EQUIPMENT

The CS.5 is a very high quality sound reproducer and will benefit from use with very good associated equipment. Since it is extremely accurate, it will reveal sources of distortion generated elsewhere in the system. For example, distortion resulting from poor recordings or inferior electronics will be reproduced accurately. Also, the quality of the interconnect cables and speaker cables will significantly effect the performance of the system.

CS.5 specifications

Thiel Audio Products has long been known for their commitment to exceptional audio fidelity, and the CS.5 is a testament to this legacy. Launched to deliver a premium listening experience, the CS.5 stands out with its meticulously engineered design and sophisticated technologies that cater to audiophiles and casual listeners alike.

One of the hallmark features of the CS.5 is its unique driver configuration. The speaker is equipped with a 1-inch titanium dome tweeter paired with a 7-inch midrange driver, ensuring clear highs and a rich, detailed midrange. This combination allows the CS.5 to reproduce a wide range of frequencies with remarkable accuracy. The speaker is designed to handle the complexities of any musical genre, making it highly versatile.

Incorporating Thiel’s innovative Constant-Q design, the CS.5 ensures a consistently neutral sound profile regardless of listening position. This technology minimizes the phase issues that can often arise in conventional speaker designs, resulting in a more cohesive sound experience. Furthermore, the speaker features a meticulously tuned bass reflex system that enhances low-frequency performance without sacrificing clarity, allowing for deep, authoritative bass that complements the overall sound signature.

Another defining characteristic of the CS.5 is its high-quality cabinet construction. Crafted from dense MDF and finished with premium veneers, the speaker not only looks elegant but is also built to reduce unwanted resonances that could interfere with sound quality. The internal bracing further strengthens the cabinet, ensuring that it can handle high power levels without distortion.

The CS.5 is designed for ease of integration into a variety of audio setups. With its standard 8-ohm impedance and a sensitivity rating that facilitates compatibility with a range of amplifiers, it provides a user-friendly experience. Additionally, the speaker is equipped with high-quality binding posts, allowing for secure connections and the flexibility to utilize bi-wiring setups.

In summary, Thiel Audio Products’ CS.5 represents a perfect blend of advanced technology, meticulous craftsmanship, and audiophile-oriented design. Its exceptional driver configuration, innovative technologies, and high-quality construction make it a standout choice for anyone looking to elevate their audio experience. Whether you are a dedicated audiophile or a casual listener, the CS.5 delivers an immersive soundstage that brings your favorite music to life. With its undeniable performance, the CS.5 solidifies Thiel Audio's reputation for excellence in the world of high-end audio.