Sennheiser LSP 500 PRO instruction manual Problem Possible cause Possible solution See

Page 57

If a problem occurs ...

Problem

Possible cause

Possible solution

See

Only the left channel of the

The Right Link mode is

Check the signal output

page 41

stereo signal is heard

activated.

configuration.

 

A loud whistling sound or feed-

The distance between micro-

Increase the distance between

 

back is heard

phone and LSP 500 PRO is too

microphone and LSP 500 PRO.

 

 

short.

 

 

 

The gain reduction of the com-

Adjust the gain reduction of

page 32

 

pressor is set too high.

the compressor.

 

 

The EQ is incorrectly adjusted.

Check the EQ settings.

page 29

The tablet app does not dis-

Device detection for the ins-

Perform device detection.

page 51

play the status information

talled receivers has not been

 

 

of the associated wireless

performed.

 

 

microphones

The installed receiver is not

Check the cable connections of

page 20

 

 

connected to the LSP 500 PRO.

the installed receiver.

 

 

The installed receiver does

The media control protocol is

 

 

not support the media control

onyl supported by devices of

 

 

protocol.

the Sennheiser ew 300 G3 and

 

 

 

ew 500 G3 series.

 

 

The IP address of the installed

Check the IP address of the

instruction

 

receiver is not valid.

installed receiver.

manual of the

 

 

 

receiver

Problems with the WLAN

Divers causes

Observe the information on

page 42

connection

 

WLAN operation.

 

A USB storage device cannot

The USB storage device is not

Check if the USB storage device

page 35

be detected or used

formatted or not compatible.

complies with the require-

 

 

 

ments specified for use with

 

 

 

the LSP 500 PRO.

 

The charge status display on

The battery pack has activated

Recharge the battery pack.

page 12

the battery pack does not light

the deep discharge protection.

 

 

up when the corresponding

The battery pack is defective.

Replace the battery pack by

page 12

button is pressed

 

a new one and dispose of the

 

 

 

 

 

 

defective battery pack.

 

Bad reception on the installed

The receiver antennas are not

Check the orientation of the

page 20

receiver, diversity reception

optimally oriented.

antennas of the installed

 

does not function properly

 

receiver.

 

The radio transmission bet-

The transmitter installed in

Set the transmitter to mono

instruction

ween 2 LSP 500 PRO is subject

the first LSP 500 PRO is set

operation.

manual of the

to interference

to stereo operation, the re-

 

transmitter

 

ceiver installed in the second

 

 

 

LSP 500 PRO can only process

 

 

 

mono signals.

 

 

 

The 2 LSP 500 PRO are too far

Reduce the distance between

 

 

away from one another; the

the 2 LSP 500 PRO; remove

 

 

radio transmission is affected

obstacles that affect the radio

 

 

by obstacles between the

transmission between the

 

 

2 LSP 500 PRO.

2 LSP 500 PRO.

 

LSP 500 PRO 57

Image 57
Contents LSP 500 PRO Content ContentLSP 500 PRO Important safety instructions Important safety instructionsHazard warnings on the rear of the product Risk of fire due to overloadingIntended use Disposal instructions Application example LSP 500 PROPackage contents Product overview Product overviewFront view Rear view Bottom viewGround Lift switch Operating elementsOperating elements Installing the LSP 500 PRO Using the LSP 500 PROUsing the LSP 500 PRO Pole mount with tilt functionConnecting the LSP 500 PRO to the mains power supply Mains and battery operationDisconnecting the LSP 500 PRO from the mains power supply Inserting the battery packsLED Charging/replacing the battery packsReplacing battery packs during operation Important information on battery operationUsing the battery pack as signal buffer Deep discharge protectionSwitching the LSP 500 PRO on Master Volume jog Functions of the Master Volume jog dialBasic operating functions Functions of the Menu jog dialLow battery warning messages Basic indications and functions shown on the display panelStatus area Escape function Adjusting the volumeActivating ground lift Lock modeUsing the LSP 500 PRO Expansion slots Connection possibilitiesAdditional inputs and outputs Installing devices in the expansion slots Required accessories and toolsOpening the expansion slot Using the LSP 500 PRO Mounting the rack mount ears LSP 500 PRO Operating the LSP 500 PRO via a tablet Operating the LSP 500 PRO via a tabletPositioning screen Information on using the appMixing Panel screen Operating the LSP 500 PRO via a tablet Edit box screenAdjusting common settings for several boxes Compressor Operating the LSP 500 PRO via a tablet EqualizerOperating menu Menu structureOperating menu Menu Equalizer Equalizer Master EQ XX Press the Menu jog dial to store your settingsEQ presets for the inputs Switching an input EQ on or offSelecting an EQ preset for an input Activating the low-cut filter Menu Virtual Bass Virtual BassAdjusts the compressor ratio Ratio Delay Menu USB Player USB player Playback mode Recording mode Adjusting the volume for the Bluetooth interface BluetoothPairing Bluetooth devices Test sound SettingsMaster Configuring the signal output to additional devicesImportant information on Wlan operation Display brightnessDisplaying the MAC address Switching the Wlan function of the LSP 500 PRO on or offAuto IP address Displaying and changing the IP addressIP subnet mask Displaying and changing the IP subnet maskSelected network Selecting a network and connecting the LSP 500 PRO toManually entering a network name Entering a network key Configuring the MIC input Adjusting the input sensitivityActivating the phantom power Detecting devices in the expansion slots Audio Resetting the settingsSystem Info System information Menu ServiceUpdating the firmware Cleaning Cleaning and maintaining the LSP 500 PROCleaning and maintaining the LSP 500 PRO StorageIf a problem occurs If a problem occursLink in input Problem Possible cause Possible solution See Error and warning messages on the display of the LSP 500 PRO Specifications Temperature Specifications Power supplyRelative air humidity Compliance withAccessories AccessoriesManufacturer Declarations FCC Sennheiser electronic GmbH & Co. KG
Related manuals
Manual 1 pages 33.93 Kb

LSP 500 PRO specifications

The Sennheiser LSP 500 PRO is a versatile, portable PA system designed for professional audio applications, making it an ideal choice for events, conferences, and performances. Renowned for its exceptional sound quality and user-friendly interface, it provides flexibility and reliability for audio professionals and public speakers alike.

One of the standout features of the LSP 500 PRO is its powerful sound reproduction. Equipped with a high-performance, 2-way speaker system, the device delivers clear, rich audio with a frequency response that caters to both speech and music. With a peak power output of 125 watts, it can fill medium to large-sized venues with ease, ensuring every attendee hears the audio clearly.

The LSP 500 PRO incorporates Sennheiser’s proprietary technologies to enhance its performance. The system includes a digital sound processor that optimizes sound dispersion, ensuring that audio is delivered evenly throughout the venue. Furthermore, it features a built-in limiter that prevents distortion, safeguarding both the system and the listener’s experience.

Portability is another major selling point of the LSP 500 PRO. Weighing just 20 kg, it is designed for easy transport, featuring a sturdy handle and a lightweight yet robust construction. The system can be powered by mains electricity or through a rechargeable battery, which provides up to 12 hours of continuous use. This flexibility allows users to set up in various locations without worrying about power supply limitations.

Connectivity options are abundant with the LSP 500 PRO. It includes multiple inputs such as XLR and Jack connectors, compatible with a range of microphones and instruments. Additionally, it features Bluetooth connectivity, enabling wireless audio streaming from smartphones or tablets. The integrated mixing console allows users to adjust levels, EQ settings, and effects, facilitating a tailored sound experience for any event.

The LSP 500 PRO also supports Sennheiser’s digital wireless microphones, offering a complete audio solution for presenters or performers who require mobility. The intuitive control panel and LED display make it easy to operate, even for those who may not be tech-savvy.

In summary, the Sennheiser LSP 500 PRO stands out for its remarkable sound quality, portability, and versatile connectivity options. Whether for public speaking, musical performances, or reliable background music, this system delivers an impressive audio experience, ensuring that every voice is heard and every note is played with clarity.