Stanley Black & Decker SD67 user manual Hose Types, Hose Safety Tags

Page 7

HOSE TYPES

The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are:

Certified non-conductive— constructed of thermoplastic or synthetic rubber inner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. Hose labeled certified non- conductive is the only hose authorized for use near electrical conductors.

Wire-braided(conductive) — constructed of synthetic rubber inner tube, single or double wire braid reinforce- ment, and weather resistant synthetic rubber cover. This hose is conductive and must never be used near electrical conductors.

Fabric-braided(not certified or labeled non-conductive) — constructed of thermoplastic or synthetic rubber in- ner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. This hose is not certified non-conductiveand must never be used near electrical conductors.

HOSE SAFETY TAGS

To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS.

If the information on a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be obtained from your Stanley Distributor.

THE TAG SHOWN BELOW IS ATTACHED TO “CERTIFIED NON-CONDUCTIVE” HOSE

 

 

 

 

 

 

 

 

 

 

 

 

A G

 

D A N G E R

 

 

 

 

 

 

D A N G E R

 

T

 

 

 

 

 

 

 

 

 

 

I S

 

1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

 

 

 

 

 

3.

DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE

 

H

 

WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRIC LINES MAY RESULT IN

 

 

 

 

 

 

OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE.

 

T

 

DEATH OR SERIOUS INJURY.

 

 

 

 

 

 

KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT

 

VE

 

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROP-

 

 

 

 

 

 

CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION

 

 

 

 

 

 

 

 

AND SEVERE PERSONAL INJURY.

 

O

 

ERLY TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND

 

 

 

 

 

 

 

 

 

ELECTRIC LINES.

 

 

 

 

 

4.

HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, ABRASION, CUTTING, OR

 

M

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT

 

E

 

 

 

 

 

 

 

 

 

 

2. BEFORE USING HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

 

 

 

 

 

 

USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

 

R

 

 

 

 

 

 

 

 

 

ON OR NEAR ELECTRIC LINES. WIPE THE ENTIRE LENGTH OF THE HOSE AND FIT-

 

 

 

 

 

5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAM-

 

T

 

 

 

 

 

 

 

 

TING WITH A CLEAN DRY ABSORBENT CLOTH TO REMOVE DIRT AND MOISTURE AND

 

 

 

 

 

 

 

 

 

 

 

 

 

AGE TO COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE

 

N O

 

TEST HOSE FOR MAXIMUM ALLOWABLE CURRENT LEAKAGE IN ACCORDANCE WITH

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IMMEDIATELY. NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

 

 

SAFETY DEPARTMENT INSTRUCTIONS.

 

 

 

 

 

6.

 

D O

 

 

 

 

 

 

 

AFTER EACH USE STORE IN A CLEAN DRY AREA.

 

 

SEE OTHER SIDE

 

 

 

 

 

 

SEE OTHER SIDE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SIDE 2

 

 

 

SIDE 1

 

 

 

 

 

 

(Shown smaller than actual size)

THE TAG SHOWN BELOW IS ATTACHED TO “CONDUCTIVE” HOSE.

D O N O T R E M O V E T H I S T A G

D O N O T R E M O V E T H I S T A G

 

D A N G E R

 

 

D A N G E R

 

 

 

 

 

1.

DO NOT USE THIS HYDRAULIC HOSE ON OR NEAR ELECTRIC LINES. THIS HOSE IS

5.

CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAMAGE TO

 

NOT LABELED OR CERTIFIED AS NON-CONDUCTIVE. USING THIS HOSE ON OR NEAR

 

COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY.

 

ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.

 

NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

2.

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY

6.

AFTER EACH USE STORE IN A CLEAN DRY AREA.

 

TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND ELEC-

 

 

 

TRIC LINES.

 

 

3.DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT

DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE

PERSONAL INJURY.

4.HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, CUTTING, OR CONTACT

WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

 

 

SEE OTHER SIDE

 

 

 

 

 

SEE OTHER SIDE

 

 

 

 

SIDE 1

 

 

 

 

 

SIDE 2

 

 

 

(Shown smaller than actual size)

D O N O T R E M O V E T H I S T A G

SD67 User Manual ◄ 7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents SD67 Page Table of Contents Local Safety Regulations Safety SymbolsSafety Precautions N G E R Tool Stickers & TagsHose Types Hose Safety TagsTool to Hydraulic Circuit Hose Recommendations Hose RecommendationsHtma / Ehtma Requirements Htma / Ehtma RequirementsCold Weather Operation PRE-OPERATION ProceduresOperating Procedures OperationTool Protection & Care Problem Cause Solution TroubleshootingCharging the Accumulator Testing the AccumulatorSpecial Tools SpecificationsSD67 Parts Illustration Model Descriptions SD67 Parts List

SD67 specifications

The Stanley Black & Decker SD67 is a highly versatile and innovative cordless screwdriver that stands out in the crowded power tool market. Designed for both DIY enthusiasts and professionals, the SD67 combines user-friendly features with advanced technology to deliver efficient and effective performance.

One of the primary features of the SD67 is its powerful motor that provides ample torque to handle a variety of fastening tasks. With a maximum torque rating of 35 in-lbs, this screwdriver can comfortably drive screws into wood, plastic, and even light metal materials, making it suitable for a myriad of applications around the home or job site.

The SD67 incorporates a lightweight and ergonomic design that enhances user comfort and reduces fatigue during extended use. Weighing in at just over 1.5 pounds, it fits seamlessly in hand, allowing for precise control and maneuverability. The soft-grip handle further contributes to a secure hold, ensuring that users maintain stability even in challenging positions.

Equipped with a 2-speed gearbox, the SD67 offers versatility in its operation. Users can easily switch between low speed (0-400 RPM) for tasks requiring greater control and high speed (0-1300 RPM) for rapid driving of screws. This adaptability is crucial for varying application needs, making the screwdriver ideal for both intricate assembly jobs and quick fixes.

An integrated LED work light is another standout feature of the SD67, illuminating dark work areas for improved visibility. This is especially helpful when working in tight spaces or dimly lit environments, allowing users to see clearly without needing to reposition a separate light source.

The tool utilizes a lithium-ion battery that ensures longer runtime and quicker charging. With the capacity to drive approximately 300 screws on a single charge, the SD67 minimizes downtime, allowing users to complete tasks efficiently. Additionally, the battery’s charge status indicator keeps you informed, helping avoid unexpected interruptions during projects.

The SD67's automatic spindle lock allows for manual screwdriving, offering added flexibility to users who need that extra level of control. Furthermore, it comes equipped with a 1/4-inch hex chuck for quick and easy bit changes, accommodating a wide range of attachments and bits.

In summary, the Stanley Black & Decker SD67 exemplifies a perfect blend of performance, comfort, and technology. With its lightweight design, powerful motor, versatile speed settings, and convenient features, it is poised to become a trusted tool in any toolkit. Whether for casual use or professional tasks, the SD67 proves to be a reliable companion for enhancing productivity and achieving results.
Top Page Image Contents