Schlage manual Panel Interface Module-RS485-NexSentry PIM-485-16-TD-NXT

Page 5

1.2 Panel Interface Module-RS485-NexSentry (PIM-485-16-TD-NXT)

The Panel Interface Module-RS485-NexSentry (PIM-485-16-TD-NXT) is a product in Schlage’s Wyreless Panel Interface Module (WPIM) category. The PIM-485-16-TD-NXT is the wireless interface to a NexSentry Star I or Star II Access Control Unit (Figure 1-2).

Figure 1-2PIM-485-16-TD-NXT Block Diagram

Up to 16 (8 for a Star I) PIM-485-16-TD-NXT can be connected via a 2 wire polled, RS-485 interface to a Star I/II.

Each PIM-485-16-TD-NXT can emulate up to 16 DR42xx DigiReaders, therefore a PIM-485-xx-NEX can control from 1 to 16 WAPM’s (1 to 8 for a Star I).

The Schlage Configuration & Demonstration Tool (CDT) is used to determine what RS-485 polling addresses each PIM-485-16-TD-NXT will emulate.

NOTE: This manual is to be used in addition to the PIM Installation Manual (M053-001-xxx) and the Wyreless Access System Configuring and Operating Manual (M053-007-xxx).

There are four steps to installing a PIM-485-16-TD-NXT:

1.Using the PIM Installation manual (M053-001-xxx) determine the optimum PIM-485-16-TD-NXT mounting location and permanently mount the PIM-485-16-TD-NXT in that location.

2.Using the NexSentry Star Access Control Unit User Guide manual (6600062B) for a Star I or the NexSentry Star II Access Control Unit User Guide manual (6600058A) for a Star II, mount the Star I/II Access Control Unit and connect it to the PC that will be running either a terminal emulator (Star I) or the NexSentry software (Star II)

Note: Make certain that that Star I/II Terminal Block TB1 is configured for the S-NET communication protocol.

3.Using this manual configure & connect the PIM-485-16-TD-NXT to the Star I/II Access Control Unit (section 2.1, page 8).

4.Using this manual, link the PIM-485-16-TD-NXT to all the WAPMs it will control (section 2.3, page 11).

IR Security & Safety

 

575 Birch St., Forestville, Connecticut 06010 / (860) 584-9158 / (860) 584-2136 fax

 

P/N: M053-016-A

http://www.irsupport.net

Page 5 of 15

Image 5
Contents NexSentry Star I/II Version World Wide Web Installation & Operating Instructions Overview Wyreless Access System WASPanel Interface Module-RS485-NexSentry PIM-485-16-TD-NXT PIM-485-16-TD-NXT Block DiagramModels Closed Enclosure Opened Internal c Antenna Remote SalesANT-REMOTE ANT-6DB-FLATPIM-485-16-TD-NXT Sales Model Table WAPMsINTERFACE/DESCRIPTION PIM Model Star Model Addr Lo Addr Hi Installing the PIM-485-16-TD-NXTMiro CDT Addr Lo, Addr Hi, & Miro Fields Range of ValuesADDR/READER Miro RS485 Connection RS485 PIM PCB & Ramm RS485 Connection Original PIM PCB & RammLinking the PIM-485-16-TD-NXT to WAPMs Channel SwitchDIP Switch Setting to Select the RF Channel What Happens if the PIM-485-16-TD-NXT Loses DC Power PIM-485-16-TD-NXT AlarmsUsing the PIM-485-16-TD-NXT Reset Switch PIM-485-16-TD-NXT Card FormatsContacting Schlage FCC Compliance FCC Compliance & WarningsVersion Date Changes Revision History