Universal Remote Control M-855 user manual System Installation, CPU Installation

Page 15

2

Installation

2.1System Installation

CPU Installation

Carefully follow the steps below to install the CPU:

1.Check and confirm that the jumpers are correctly set for the CPU you are going to install (figure 3).

2.Take the screwdriver and releasing screw-nut of the Socket 478.

3.Rotate mark of screw-nut to face the “OPEN”.

4.Align the pins of the CPU against the pinholes of the Socket 478. Be sure to pay attention to the orientation of the CPU.

OPEN

OPEN

Screw Nut

CLOSED

CLOSED

Figure 3: CPU Socket

5.Push down the CPU into the Socket 478.

6.Rotate mark of screw-nut to face the “CLOSED”.

7.Place the CPU cooling fan atop the CPU surface.

OPEN

CLOSED

Installation • 9

Image 15

Contents User’s Manual 855 Industrial MotherboardPage Trademarks Adlink Technology INC Detailed Company InformationQuestions Table of Contents Page Introduction Unpacking Checklist Features Shield ConnectorHardware Monitoring ¡ Lvds ¡ VGA Series OverviewGmch 855GME System Block Diagram¡ Lvds & VGA Specifications¡ Weight ¡ Rear I/O Connectors¡ Internal I/O Connectors pin-header ¡ BiosPage CPU Installation System InstallationHeat Sink & Retention Module Installation Memory Module InstallationRemoving a CPU Removing a Dimm Dimm Memory and 184-pins SocketPage Board Layout Jumper and Connector Locations InstallationJP1/JP2 Jumper Settings COM3/COM4 Port Setting Select JP1/JP2 Function Jumpers FunctionsJP3 JP4JP5 Connector Descriptions Power Management Setting Select JP6 FunctionJP6 Connectors Functions Table for Connector’s Location DescriptionVCC USB 0/1 Connectors 4-pins Female CN4 Pin # Assignment Blue Green Red USB 2/3 Connector 4-pins Female CN7 Pin # Assignment COM3 Figure Cdin Connector CN9 Pin # AssignmentCOM4 Figure CPU Fan Power Connector CN15 Pin # Assignment System Fan Power Connector CN18 Pin # Assignment HDD LED Reset PWR onSpeaker PWR LED KeylockDRQ ATX Power Connector CN22 Pin # Assignment Address Chip Select LAN LED Connector JP7 Pin # Assignment Line OUT Connector CN25 Pin # AssignmentATA2 Connector 9-pins SATA2 Pin # Assignment ATA1 Connector 9-pins SATA1 Pin # AssignmentType II CompactFlash Connector CF Pin # Assignment Main Menu Bios InstructionsAdvanced Chipset Features Setup ItemsStandard Cmos Features Advanced Bios FeaturesStandard Cmos Features JUN Total Memory Option N/A IDE AdaptersBase Memory Option N/A Extended Memory Option N/APage Advanced Bios Features CPU FeatureThermal Management Boot Other Device Hard Disk Boot PriorityQuick Power On Self Test First/Second/Third Boot DeviceTypematic Delay Msec Boot Up Floppy SeekBoot Up NumLock Status Typematic Rate SettingAdvanced Chipset Features Report No FDD For WinDram Timing Selectable System Bios Cacheable Active To Precharge DelayDram RAS# To CAS# Delay Dram Data Integrity ModeOn-Chip VGA Setting Video Bios CacheableDelayed Transaction Delay Prior To ThermalPanel Number Integrated PeripheralsIDE Primary/Secondary Master/Slave Udma IDE HDD Block ModeOnChip Primary/Secondary PCI IDE IDE Primary/Secondary Master/Slave PIOAC97 Audio Power On FunctionUSB Keyboard Support USB Mouse SupportEPP Mode Select KB Power on PasswordHot Key Power on Parallel Port ModePower Management Setup Dpms Suspend Type Suspend ModeHDD Power Down Resume by AlarmIRQ Resources PnP/PCI ConfigurationsReset Configuration Data Resources Controlled ByVdimm PC Health StatusCpufan SysfanLoad Fail-Safe Defaults Frequency/Voltage ControlVbat Supervisor/User Password Setting Load Optimized DefaultsQuit without saving Y/N? Y Exiting Bios SetupSave to Cmos and Exit Y/N? Y Exit Without SavingWarranty Policy