Universal Remote Control M-855 user manual Trademarks

Page 3

©Copyright 2004 ADLINK Technology Inc. All Rights Reserved.

Manual Rev. 1.00: August 16, 2004

The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

Trademarks

NuDAQ®, NuIPC®, NuDAM®, NuPRO® are registered trademarks of ADLINK Technology Inc. Other product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

Image 3
Contents User’s Manual 855 Industrial MotherboardPage Trademarks Adlink Technology INC Detailed Company InformationQuestions Table of Contents Page Introduction Unpacking Checklist Features Shield ConnectorHardware Monitoring ¡ Lvds ¡ VGA Series OverviewGmch 855GME System Block Diagram¡ Lvds & VGA Specifications¡ Weight ¡ Rear I/O Connectors¡ Internal I/O Connectors pin-header ¡ BiosPage CPU Installation System InstallationHeat Sink & Retention Module Installation Memory Module InstallationRemoving a CPU Removing a Dimm Dimm Memory and 184-pins SocketPage Board Layout Jumper and Connector Locations InstallationJP1/JP2 Jumper Settings COM3/COM4 Port Setting Select JP1/JP2 Function Jumpers FunctionsJP3 JP4JP5 Connector Descriptions  Power Management Setting Select JP6 FunctionJP6 Connectors Functions Table for Connector’s Location DescriptionVCC USB 0/1 Connectors 4-pins Female CN4 Pin # Assignment Blue Green Red  USB 2/3 Connector 4-pins Female CN7 Pin # Assignment COM3 Figure Cdin Connector CN9 Pin # AssignmentCOM4 Figure CPU Fan Power Connector CN15 Pin # Assignment System Fan Power Connector CN18 Pin # Assignment HDD LED Reset PWR onSpeaker PWR LED KeylockDRQ ATX Power Connector CN22 Pin # Assignment Address Chip Select LAN LED Connector JP7 Pin # Assignment Line OUT Connector CN25 Pin # AssignmentATA2 Connector 9-pins SATA2 Pin # Assignment ATA1 Connector 9-pins SATA1 Pin # AssignmentType II CompactFlash Connector CF Pin # Assignment Main Menu Bios InstructionsAdvanced Chipset Features Setup ItemsStandard Cmos Features Advanced Bios FeaturesStandard Cmos Features JUN Total Memory Option N/A IDE AdaptersBase Memory Option N/A Extended Memory Option N/APage Advanced Bios Features CPU FeatureThermal Management Boot Other Device Hard Disk Boot PriorityQuick Power On Self Test First/Second/Third Boot DeviceTypematic Delay Msec Boot Up Floppy SeekBoot Up NumLock Status Typematic Rate SettingAdvanced Chipset Features Report No FDD For WinDram Timing Selectable System Bios Cacheable Active To Precharge DelayDram RAS# To CAS# Delay Dram Data Integrity ModeOn-Chip VGA Setting Video Bios CacheableDelayed Transaction Delay Prior To ThermalPanel Number Integrated PeripheralsIDE Primary/Secondary Master/Slave Udma IDE HDD Block ModeOnChip Primary/Secondary PCI IDE IDE Primary/Secondary Master/Slave PIOAC97 Audio Power On FunctionUSB Keyboard Support USB Mouse SupportEPP Mode Select KB Power on PasswordHot Key Power on Parallel Port ModePower Management Setup Dpms Suspend Type Suspend ModeHDD Power Down Resume by AlarmIRQ Resources PnP/PCI ConfigurationsReset Configuration Data Resources Controlled ByVdimm PC Health StatusCpufan SysfanLoad Fail-Safe Defaults Frequency/Voltage ControlVbat Supervisor/User Password Setting Load Optimized DefaultsQuit without saving Y/N? Y Exiting Bios SetupSave to Cmos and Exit Y/N? Y Exit Without SavingWarranty Policy