Worth Data P11/12 user manual Many of the specifications are available online at

Page 47

MOD 10 UCC 128 is enabled by scanning the appropriate bar codes on the TriCoder Setup Menu or by keypad in the PROGRAMMING MODE "Change Setup" option. If MOD 10 UCC 128 is enabled, you will NOT be able to read a standard Code 128 bar code that does not have the Function 1 character and the Mod 10 check character.

UCC/EAN Code 128 Serial Shipping Container Code

The UCC 128 specification is used extensively by the retail industry. If you have a requirement for a UCC 128 Serial Shipping Container bar code, be sure to follow the specification as closely as possible as many vendors will impose fines for non- conformance. For more information on UCC 128, contact the Uniform Code Council at:

Uniform Product Code Council, Inc.

8163 Old Yankee Road, Suite J

Dayton, Ohio 45458

(513) 435-3870

Many of the specifications are available online at:

http://www.uc-council.org

F-2

Image 47

Contents Worth Data WDP Keyboard Wedge Reader For Model P11/12 Introduction Components of WDP Reader InstallationIntegrated Laser WDP Readers InstallationInternal Installation on PC P11/12 External WedgeExternal Wedge Installation on PC or Mac USB Installation on a PC or Mac Configuring the WDP Reader for your computer Application WDP Reader SetupUsing the WDP Reader Setup Menu Code WDP Setup ParametersBeep Tone UPC/EAN 5 Data Length 5 CodeCodabar Disable UCC-128/EAN-128Computer Interface MSI and PlesseyBar Code Data Preamble Data Transmitted PreamblePostamble MagStripe ResetData Transmission Timing Keyboard Country CharactersTerminator Characters If you are unable to read the Test Label Testing the WDP reader with your computerBar-code wands, laser scanners and CCD touch scanners Bar Code and MagStripe Slot ScannersWands Scanners and Scanning TechniqueWand Scanning Technique Using the Bar Code Slot Scanner Using the MagStripe Slot Scanner Worth Data LZx00 series Laser and CCD ScannersClass II Laser Product CCD Scanners Right Wrong Tips for using CCD’s and LasersCode Start SetupEnd Setup Laser scanner optionsFunction keys F11 and F12 Special FeaturesFunction and Control Key Support Function keys F1 through F10, and numeric-pad keysWindows Key Macintosh Command and Option Keys on USBShift, Ctrl and Alt keys Accumulate Mode Reader wont beep when reading bar codes TroubleshootingPoor read rate Reader transmits incorrect data to the screenVolt power adapters for external wedge installation Changing the volume of the WDP Readers beeperOpening the WDP Case Slot Installation with Keyboard Cabling ISA Internal Board InstallationNow turn to page 7 to configure the WDP Reader BusKey P=ppp I=i Slot Installation with Bus CommunicationInstalling BusKey BusKey ParametersInterrupt Number jumper JP4, the Interrupt Number jumper Jumper SettingsJP7, the Interface Method jumper JP5, the Port Address jumperJP9, the Wand/Magstripe jumper JP8, the Laser Decode Light/Wand jumperSpecifications for Code Value 22 is the Check Character Mod 43 Check Character+ 2 + 3 + 33 + 34 + 35 = 108/43 = 2 with a RemainderFull Ascii Extension to Code Codabar start/stop transmission CodabarUCC-128/ EAN-128 Code 128 SpecificationsMany of the specifications are available online at + 9 x 3 = Interleaved 2 of 5 CodeEven Odd + 1 =019873 + 48 =60 57 = 19873UPC Specifications UPC 2 and 5-character supplemental codes Isbn SpecificationsUPC/EAN checksum character 01234565 UPC-E Checksum Calculation1234500006 01234500006MSI Mod 10 check digit is calculated as follows MSI/Plessey SpecificationsMSI Mod 11 check digit is calculated as follows Code 93 Specifications Ascii Code Equivalent Table Firmware Upgrades