Worth Data P11/12 user manual WDP Setup Parameters, Beep Tone, Code

Page 9

WDP Setup Parameters

Beep Tone

Lowest

0

Low

1

Medium

2

High

3

Highest

4

Turn Beeper OFF

5

The WDP Reader gives you a choice of five different beep pitches. (Beep volume is also adjustable -- see page 32 for the details.)

Code 39

Enable Code 39

0

Disable Code 39

1

Enable Full ASCII Code 39

2

Disable Full ASCII Code 39

3

Enable Code 39 Accumulate Mode

4

Disable Code 39 Accumulate Mode

5

Enable Start/stop character transmission

6

Disable Start/Stop character transmission

7

Enable Mod 43 Check Digit

8

Disable Mod 43 Check Digit

9

Enable Check Digit Transmission

A

Disable Check Digit Transmission

B

Caps Lock ON

C

Caps Lock OFF

D

For information about Code 39, Full ASCII Code 39 and Accumulate Mode, see Appendix D.

Enabling Start/Stop character transmission means that the WDP Reader will transmit the * Start/Stop characters to your computer along with the data. For example, data of 1234 would be transmitted as *1234*. Most people don't need this option, but it is useful if you want your software to be able to differentiate between keyboard and bar code data.

Enabling the Mod 43 Check Digit requires the units position of your data to match the calculation for the check digit explained in Appendix D. If you've enabled the check digit, enabling Check Digit transmission causes the reader to transmit the check digit to your computer along with the bar code data.

"Caps Lock ON" means that lower case letters read as data will be transmitted as upper case, and upper case as lower. Numbers, punctuation and control characters are not affected. "Caps Lock OFF" means that letters will be transmitted exactly as read.

2-3

Image 9
Contents Worth Data WDP Keyboard Wedge Reader For Model P11/12 Introduction Components of WDP Reader InstallationInternal Installation on PC P11/12 InstallationExternal Wedge Integrated Laser WDP ReadersExternal Wedge Installation on PC or Mac USB Installation on a PC or Mac Configuring the WDP Reader for your computer Application WDP Reader SetupUsing the WDP Reader Setup Menu WDP Setup Parameters Beep ToneCode UPC/EAN 5 Data Length 5 CodeCodabar Disable UCC-128/EAN-128Computer Interface MSI and PlesseyBar Code Data Preamble Data Transmitted PreamblePostamble Reset Data Transmission TimingMagStripe Keyboard Country CharactersTerminator Characters Bar-code wands, laser scanners and CCD touch scanners Testing the WDP reader with your computerBar Code and MagStripe Slot Scanners If you are unable to read the Test LabelWands Scanners and Scanning TechniqueWand Scanning Technique Using the Bar Code Slot Scanner Using the MagStripe Slot Scanner Worth Data LZx00 series Laser and CCD ScannersClass II Laser Product CCD Scanners Right Wrong Tips for using CCD’s and LasersEnd Setup Start SetupLaser scanner options CodeFunction and Control Key Support Special FeaturesFunction keys F1 through F10, and numeric-pad keys Function keys F11 and F12Macintosh Command and Option Keys on USB Shift, Ctrl and Alt keysWindows Key Accumulate Mode Reader wont beep when reading bar codes TroubleshootingPoor read rate Reader transmits incorrect data to the screenVolt power adapters for external wedge installation Changing the volume of the WDP Readers beeperOpening the WDP Case Slot Installation with Keyboard Cabling ISA Internal Board InstallationNow turn to page 7 to configure the WDP Reader Installing BusKey Slot Installation with Bus CommunicationBusKey Parameters BusKey P=ppp I=iInterrupt Number jumper JP4, the Interrupt Number jumper Jumper SettingsJP7, the Interface Method jumper JP5, the Port Address jumperJP9, the Wand/Magstripe jumper JP8, the Laser Decode Light/Wand jumperSpecifications for Code + 2 + 3 + 33 + 34 + 35 = Mod 43 Check Character108/43 = 2 with a Remainder Value 22 is the Check CharacterFull Ascii Extension to Code Codabar start/stop transmission CodabarUCC-128/ EAN-128 Code 128 SpecificationsMany of the specifications are available online at Even Odd Interleaved 2 of 5 Code+ 1 = + 9 x 3 =60 57 = + 48 =19873 019873UPC Specifications UPC 2 and 5-character supplemental codes Isbn SpecificationsUPC/EAN checksum character 1234500006 UPC-E Checksum Calculation01234500006 01234565MSI Mod 10 check digit is calculated as follows MSI/Plessey SpecificationsMSI Mod 11 check digit is calculated as follows Code 93 Specifications Ascii Code Equivalent Table Firmware Upgrades