SV Sound PB10-ISD manual Menu to check these critical choices

Page 8

Page 8

“menu” to check these critical choices).

SV Subwoofers

•Is your receiver connected to the sub amp? Use a well-shielded RCA cable (sometimes called a “patch cord”) to hook to the subwoofer output of your DD/DTS receiver to the RCA input jack of your SVS amplifier. As mentioned earlier, you’ll need to “split” the subwoofer signal with a “Y Cable” if you bought a pair of subs.

•Is your Radio Shack ® sound pressure level (SPL) meter ready? This tool is absolutely essential to proper home theater audio setup. It’s akin to a tire pressure gauge for your car (you don’t set your tires by “feel” right?). Set the meter to “Slow” and “C-weighting” (and turn the dial to 70 or 80dB depending on your test tone source). Haven’t got the meter yet? Order one from L-Sound. We prefer the analog instead of the digital display model.

Getting ready to start now: Make sure your receiver/processor master volume is set at “00 dB” or some other easy to remember reference level. Finally, ensure your SVS’s volume/gain control is set no more than 1/4 to 1/3rd up, for now. It’s also critical to check the subwoofer level control of your surround receiver before you begin the test tones. Set the subwoofer output signal no higher than “-5 dB” initially (that’s one quarter way up, given a typical receiver’s subwoofer channel level limits of –10 dB to +10 dB) . Your LFE “trim” or “peak limiter”, if you have one, should be set to 0dB to start (that’s full up) but this can be dialed down later to tame peaks if needed. Turn off any sound-field processing modes, “midnight mode” etc. Your LFE should go to the “subwoofer only”, not “mains” too, if this is an option in your system.

Now play your receiver's internal test tones so you have something to measure with your SPL meter. Or, buy a test DVD such as the Avia. A test disk’s tones ensure your entire signal path, from the DVD player to your speakers, is set correctly. Whatever you use, when the tones start alternating from speaker to speaker (watch your sound meter now), set each speaker’s volume to about 75 dB (or 85dB if using Avia) by using the receiver’s dedicated channel level controls (leaving receiver’s master volume the same). We recommend you turn down the receiver’s subwoofer output level before you significantly lower your sub’s volume/ gain control. This helps keep distortion sent to your SVS to a minimum. You should not be set this control lower than –5 dB however, since some adjustment room is needed to fine tune levels later. If your subwoofer

Page 7 Page 9
Image 8
Page 7 Page 9
Contents I D E SV Subwoofers SV Subwoofers Welcome About your SV Subwoofer Setup, calibrating and integration More Setup, calibrating and integration Menu to check these critical choices PagePage9 SV Subwoofers Bassy demo scenes to die for More Bassy demo scenes Glossary of Home Theater Terms SV Subwoofers SV Subwoofers Terms and Conditions

PB10-ISD specifications

The SV Sound PB10-ISD is an innovative subwoofer designed for audiophiles and casual listeners alike, delivering powerful and immersive low-frequency sound. This subwoofer stands out for its combination of advanced technology, elegant design, and exceptional performance, making it an ideal addition to any home theater or music system.

One of the primary features of the PB10-ISD is its robust 10-inch driver. This driver is engineered to produce deep, rich bass while maintaining accuracy and clarity. The design incorporates a high-excursion cone, enabling it to push more air and generate impactful sound waves, resulting in an engaging listening experience. The driver is housed in a well-constructed ported enclosure optimized for low-frequency output, ensuring that the subwoofer can generate the deep bass tones that create a sense of realism in movies and music.

The PB10-ISD is powered by a high-efficiency amplifier, providing up to 300 watts of peak power. This amplifier is designed with low distortion and high headroom, allowing the subwoofer to perform effectively even at high volumes. The combination of the powerful driver and the capable amplifier gives the PB10-ISD the ability to fill large rooms with deep, engaging bass without compromising sound quality.

One of the standout technologies in the PB10-ISD is its Intelligent Signal Detection (ISD) feature. This technology allows the subwoofer to enter standby mode when it is not receiving an audio signal, conserving energy while maintaining readiness. The automatic power on/off function enhances convenience and ensures that the subwoofer is always operating efficiently.

Another notable characteristic of the PB10-ISD is its adjustable volume control and phase switch. These features empower users to fine-tune the bass response according to their preferences and the acoustics of their room. The ability to customize the sound output makes it easier for listeners to achieve optimal audio performance tailored to their specific setup.

The SV Sound PB10-ISD combines versatility with aesthetic appeal. It boasts a sleek design that can complement any home decor. Its compact size allows for flexible placement in various room configurations.

In summary, the SV Sound PB10-ISD subwoofer is a compelling option for those seeking a high-performance audio solution. With its powerful driver, efficient amplifier, and intelligent features, it delivers exceptional low-frequency sound, making it perfect for movie enthusiasts and music lovers alike.
Top Page Image Contents