Panasonic CF-74 appendix Troubleshooting Basic, „ Starting Up

Troubleshooting (Basic)

Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the “Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, contact Panasonic Technical Support (Î page 30). You can also check the computer’s status in the PC Information Viewer

(Î Reference Manual “Troubleshooting (Advanced)”).

„Starting Up

Cannot start up.	z Connect the AC adaptor.
The power indicator or bat-	z Insert a fully charged battery.
tery indicator is not lit.	z Remove the battery pack and the AC adaptor, then connect them again.
	z If a device is connected to the ExpressCard slot or the USB port, disconnect the
	device, or set [ExpressCard Slot], [USB Port] or [Legacy USB Support] to [Disable]
	in the [Advanced] menu of the Setup Utility.
The power is turned on but	z The computer is warming up before start up. Wait for the computer to start up (takes up
“Warming up the system (up	to 30 minutes). If, “Cannot warm up the system” is displayed, the computer failed to
to 30 minutes)” appears.	warm up and does not start. In this case, turn off the computer, leave it in an environ-
	ment of 5 °C {41 °F} or higher temperature for about an hour, and then turn on the power
	again.
Cannot turn on the computer.	z Leave it in an environment of 5 °C {41 °F} or higher temperature for about an hour, then
The computer does not	turn on the power again.
resume from standby.
(The power indicator blinks
quickly in green.)
You have forgotten the	z Supervisor Password or User Password: Contact Panasonic Technical Support (Î page
password.	30).
	z Administrator password:
	•	If you have a password reset disk, you can reset the administrator password. Set the
		disk and enter any wrong password, then follow the on-screen instructions and set a
	•	new password.
		If you do not have a password reset disk, reinstall (Î page 20) and set up Windows,
		and then set a new password.
“Remove disks or other	z A floppy disk is in the drive and it does not contain system startup information. Remove
media. Press any key to	the floppy disk and press any key.
restart” or a similar mes-	z This message may appear with some devices connected to the ExpressCard slot or the
sage appears.	USB port. Remove the device, or set [ExpressCard Slot], [USB Port] or [Legacy USB
	Support] to [Disable] in the [Advanced] menu of the Setup Utility.
	z If the problem persists after removing the disk, it may be a hard disk failure. Contact
	Panasonic Technical Support (Î page 30).
Windows startup and opera-	z Press			in the Setup Utility (Î page 22 “To start the Setup Utility”) to return the Setup
			F9
tion is slow.	Utility settings (excluding the passwords) to the default values. Start the Setup Utility and
	make the settings again. (Note that the processing speed depends on the application
	software, so this procedure may not make Windows faster.)
	z If you installed a resident software after purchase, turn off the residence.
	z Disable Indexing Service in the following menu.
	Click [start] - [Search] - [Change preferences] - [Without Indexing Service]
The date and time are incor-	z Make the correct settings. Click [start] - [Control Panel] - [Date, Time, Language, and
rect.	Regional Options] - [Date and Time].
	z If the problem persists, the internal clock battery may need to be replaced. Contact
	Panasonic Technical Support (Î page 30).
	z When the computer is connected to LAN, check the date and time of the server.
	z The 2100 A.D. or later year will not be correctly recognized on this computer.
[Executing Battery Recali-	z The Battery Recalibration was canceled before Windows was shut down last time. To
bration] screen appears.	start up Windows, turn off the computer by the power button, and then turn on.
[Enter Password] does not	z To display [Enter Password] at resuming, set the Windows password. The password you
appear when resuming from	have set in the Setup Utility is not requested at resuming.
standby/hibernation.	A Click [start] - [Control Panel] - [User Accounts] and select the account, and set the
		password.
	B Click [start] - [Control Panel] - [Performance and Maintenance] - [Power Options] -
		[Advanced] and add a check mark for [Prompt for password when computer resumes
		from standby].

Troubleshooting Useful Information Getting Started

Appendix

23