Panasonic CF-52EKM 1 D 2 M Safety Precautions, Lithium Battery, Important Safety Instructions

Page 4
SAFETY PRECAUTIONS

SAFETY PRECAUTIONS

1.Before servicing, unplug the power cord to prevent an electric shock.

2.When replacing parts, use only manufacture's recommended components for safety.

3.Check the condition of the power cord. Replace if wear or damage is evident.

4.After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc.

Important Safety Instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

1.Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

2.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

3.Do not use the telephone to report a gas leak in the vicinity of the leak. vicinity of the leak.

4.Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.

SAVE THESE INSTRUCTIONS

LITHIUM BATTERY

This computer contains a lithium battery to enable the date, time, and other data to be stored. The battery should only be exchanged by authorized service personel.

Warning! A risk of explosion from incorrect installation or misapplication may possibly occur.

LITHIUM BATTERY Important Safety Instructions

LITHIUM BATTERY CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the equipment manufacturer. Dispose of used batteries according to the manufacturer's instructions.

LITHIUMBATTERIES LITHIUM BATTERY

Vorsicht!

Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben order einen vom Hersteller empfohlenen ähnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.

PILE AU LITHIUM LITHIUMBATTERIES

ATTENTION: IL Y A DANGER D'EXPLOSION S' IL Y A REMPLACEMENT INCORRECT DE LA PILE. REMPLACER UNIQUEMENT AVEC UNE PILE DU MÈME TYPE OU D'UN TYPE RECOMMANDÉ PAR LE CONSTRUCTEUR. METTRE AU RÉBUT LES PILES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS DU FABRICANT.

Image 4
Contents H Smart Card Reader, Finger Print Reader Configurated This is the Service Manual for the following areasModel No. CF-52EKMxDxM Notebook ComputerFor U.K How to replace the fuseThis apparatus must be earthed for your safety LASER SAFETY INFORMATION For U.S.ASAFETY PRECAUTIONS LITHIUM BATTERYImportant Safety Instructions LITHIUM BATTERYPrecautions Battery Pack Appendix Troubleshooting Useful Information Getting StartedDo Not Charge the Battery Using Methods Other Than Those Specified Do Not Use with Any Other ProductCONTENTS 1. Specifications Intel WiFi LinkBluetooth *14 Model NoSoftware OS*25Bluetooth Only for model with Bluetooth Wireless LANdepending on writing status and recording format. Also, some 2. Names and Functions of Parts Specified Battery pack CF-VZSU29ASUOnly for model with wireless LAN/wireless WAN Reference Manual “Wireless LAN”A B C F H I J L M NFingerPrint Bluetooth uFCBGAL2 Cache 4M Clock Speed 2GHz Processor4 Diagnosis Procedure 4.2. Troubleshooting Flow ChartError Diagnosis by Checking Beep Signal Sound 5 Power-On Self Test Boot CheckOutline of POST 6 List of Error Codes Only when the port replicator is connected 02D0 System cache error - Cache disabled 7 Self Diagnosis Test 1. Beginning of self-diagnosis test 1-1. Setting of content of setup1-2. When you execute an automatic test 1-3. When you execute the enhancing test2. Operation of PC-Diagnostic Utility 2-3. The content of the setup is returned to the setting of the user 2-2. PC-Diagnostic utility End method2-1. Selection of tested device 3. Test Item and Division of trouble Place with possibility of breakdown All memory space is tested in a specialTest Item 8 Wiring Connection Diagram 9.1. Disassembly Instructions 9 Disassembly/Reassembly9.1.1. Disassembly Flowchart 9.1.3.1. Battery Pack 9.1.2. Preparation9.1.3.2. HDD Mounting Kit 9.1.3.3. DVD Multi Drive9.1.5. Removing the Tilt Panl Ass’y 9.1.7. Removing the ROBSON Cover, Wireless LAN Module and BIOS PCB9.1.6. Removing the DIMM Memory Card 9.1.7.2. BIOS PCB 9.1.7.1. Wireless LAN Module9.1.8. Removing the Display unit 9.1.9. Removing the LCD unit, Inverter Ass’y and ANTENNA PWB L,R 9.1.10. Removing the Handle Assy9.1.11. Removing the Modem 9.1.12.2. Speaker R9.1.12.3. Speaker L 9.1.13. Removing the Keyboard9.1.14. Removing the Top Cover 9.1.15. Removing the Pad and TOUCH PAD PCB9.1.16. Removing the SD PCB Cover9.1.17. Removing the WWAN PCB 9.1.19. Removing the PWR BATTERY LED PCB9.1.18. Removing the AUDIO PCB 9.1.20. Removing the KBD Earth Plate 9.1.21. Removing the Hinge Support R9.1.22. Removing the Fan Ass’y Cover PC card9.1.24. Removing the Battery Connector Ass’y 9.1.23. Removing the Hinge Support L and MP Hold Plate9.1.25. Removing the SC RELAY PCB and HDD Hold Plate 9.1.26. Removing the Heat Sink Ass’y9.1.27. Removing the SERIAL PCB 9.1.28. Removing the MAIN HIGH PCB9.2.1. Attention when CF-52 series is repaired 9.2. Reassembly Instructions9.2.2. Setting the MAIN HIGH PCB Setting of Main PCB before assembling S1Insulation S2Bitten S3Sharp Edge S4Part No. Check S5OtherTHERMAL SHEET SCREW Torque of tightening screw 0.18±0.02N・m≒1.8±0.2kgf・cmTHERMAL SHEET S4Part No. Check S5Other9.2.4. Setting the Heat Sink Ass’y 9.2.3. Setting the SERIAL PCBHex spacer No.3 9.2.5. Setting the Fan Ass’y How to assemble the Heat Sink Ass’y and Fan Ass’y9.2.6. Setting the SC RELAY PCB and HDD Hold Plate SC RELAY PCBHDD hold plate No.1S4Part No. Check S5Other 9.2.7. Setting the Battery Connector Ass’y 9.2.8. Setting the Hinge Support L and MP Hold Plate9.2.9. Setting the Hinge Cover R How to place the Cable9.2.10. Setting the KBD Earth Plate 2. Fix the KBD Earth Plate using the four Screws N4. No.1 to No.43. Fix the KBD Earth Plate using the two ScrewsN13 4. Paste the tape, and connect the FPC to the ConnectorCN349.2.11. Setting the PWR BATTERY LED PCB 9-229.2.12. Setting the AUDIO PCB Arranging the Cable and setting the WL button9.2.13. Setting the WWAN PCB Arranging the Cables and Tapes9.2.14. Setting the SD PCB 9.2.15. Setting the Pad and TOUCH PAD PCB9.2.16. Setting the Top Cover 9.2.17. Setting the Keyboard 1. Connect the FPCs to the Connector on the KBD FPCTape Tape Screws N2 DFHE5122YA 9-27Caution for when assembling the Keyboard 9.2.18. Setting the Speakers 9.2.19. Setting the ModemHow to paste the Tape 9.2.20. Setting the Handle Ass’y 9.2.21. Setting the LCD Unit, Inverter Ass’y and Antenna PWB L, R Using JIG Using JIGSchematic for sticking at Point A SHIELD SHEET A LCDThe Cable is under the base plate Along the slot Along the slotTAPE LCD DAMPER ERefer to the specification pictures on the left Safety Critical ComponentsSHEET LCD ASSYPage 9.2.22. Setting the Display Unit, BIOS HIGH PCB and SW LED MDC PCB 6. Fix the SW LED MDC PCB using the six Screws N2. No.1 to No.6 Arranging the Cables when assembling the LCD UnitScrewN2 DFHE5122YA Screw N4 DRHM0093ZA 9-38Page 9.2.23. Setting the Wireless LAN Module, BIOS PCB and ROBSON Cover Arranging the Speaker Cables when assembling the SW LED MDC PCB9.2.24. Setting the DIMM Memory Card and DIMM Cover 9.2.25. Setting the Tilt Panel Ass’yScrew N202 DRSB2+4FKLT Caution for when assembling the Tilt Panel Ass’y9-42 9.2.26. Setting the HDD 1. Connect the HDD FPC Ass’y to the HDD2. Insert the HDD Ass’y into the HDD Damper 3. Set the HDD Ass’y into the HDD Case Upper10 Exploded View CF-52EKMxDxMScrew tightening torque A SF7 SF3 A SF8 A SF8 SF6 SF4 SF5 SF1 CF-52EKMHDxM with Smart Card Reader and Finger Print Reader only SF2A 0.18 ± 0.02 N.m 1.8 ± 0.2 kgf.cm B 0.18 ± 0.01 N.m 1.8 ± 0.1 kgf.cm K92-2 Screw tightening torqueK92-1 4.4 ± 0.2 kgf.cm Replacement Parts List AccessoriesCF-52EKMxDxM REF. NO and AREAPacking Material Mechanical PartsK92-1 K125 CF-52EKMHDxM SmartCard Reader, Finger Print Reader DVD MULTI DRIVEDESCRIPTION MAIN PCB HIGH502, 503, 506, 508 512, 513, 514, 515522, 523, 524, 525 529, 530, 531, 532C 100, 102, 120, 121 F1G0J105A001CAPACITOR, 6.3V, 1µF 146, 148, 165, 242CONNECTOR CONNECTOR, USB1010 F1G1H181A495POWER MANAGEMENT SWTICH IC, FET SWITCHIC, USB POWER SW IC, SWITCHDC POWER LINE BEADS DC POWER LINE INDUCTORC0DBDJH00009 IC, LINERB1DHDC000028 Q 1001B1CFRD000009 Q 1004, 1005, 1006R 103, 107, 363, 365 D0GA472JA023RESISTOR, 1/16W, 4.7KO 424, 425, 445, 499D1BA4530A023 D0GA121JA023D0GD1R0JA052 RESISTOR, 1/8W, 1OAUDIO PCB PWR BATTERY PCB SERIAL PCBTOUCH PAD PCB SW LED PCBBIOS PCB HIGH BLUETOOTH PCBWWAN PCB WLAN ANTENNA R PCB