Panasonic CF-52EKM 1 D 2 M service manual Setting the Handle Ass’y

Page 54
9.2.20. Setting the Handle Ass’y

9.2.20. Setting the Handle Ass’y

1.Assemle the Handle Ass’y (Grip Upper, Grip Lower, Handle Base L, Handle Base R, Handle Ring and Handle Pom), and fix them using the two Screws <K92-5>.

2.Fix the Handle Base Ass’y to the computer using the two Screws <K172>.

Paste the Handle Sheet on the Screws <K172>.

Grip upper

Handle ring

Handle base L

Handle <K172> sheet

Handle ring

Grip lower

<K92-5>

Handle pom

Handle ring

<K172> Handle sheet Handle ring

Handle pom

Handle base R

Screws <K92-5>: DRSB3+8FKLT

Screws <K172>: DRYN4+J12KLT

9-31

Image 54
Contents Model No. CF-52EKMxDxM H Smart Card Reader, Finger Print Reader ConfiguratedThis is the Service Manual for the following areas Notebook ComputerHow to replace the fuse For U.KThis apparatus must be earthed for your safety LASER SAFETY INFORMATION For U.S.AImportant Safety Instructions SAFETY PRECAUTIONSLITHIUM BATTERY LITHIUM BATTERYDo Not Charge the Battery Using Methods Other Than Those Specified Precautions Battery PackAppendix Troubleshooting Useful Information Getting Started Do Not Use with Any Other ProductCONTENTS Bluetooth *14 1. SpecificationsIntel WiFi Link Model NoSoftware OS*25Wireless LAN Bluetooth Only for model with Bluetoothdepending on writing status and recording format. Also, some Only for model with wireless LAN/wireless WAN 2. Names and Functions of PartsSpecified Battery pack CF-VZSU29ASU Reference Manual “Wireless LAN”A B C F H I J L M NL2 Cache 4M Clock Speed 2GHz FingerPrint BluetoothuFCBGA Processor4 Diagnosis Procedure 4.2. Troubleshooting Flow Chart5 Power-On Self Test Boot Check Error Diagnosis by Checking Beep Signal SoundOutline of POST 6 List of Error Codes Only when the port replicator is connected 02D0 System cache error - Cache disabled 1-2. When you execute an automatic test 7 Self Diagnosis Test1. Beginning of self-diagnosis test 1-1. Setting of content of setup 1-3. When you execute the enhancing test2. Operation of PC-Diagnostic Utility 2-2. PC-Diagnostic utility End method 2-3. The content of the setup is returned to the setting of the user2-1. Selection of tested device ty of breakdown 3. Test Item and Division of troublePlace with possibili All memory space is tested in a specialTest Item 8 Wiring Connection Diagram 9 Disassembly/Reassembly 9.1. Disassembly Instructions9.1.1. Disassembly Flowchart 9.1.3.2. HDD Mounting Kit 9.1.3.1. Battery Pack9.1.2. Preparation 9.1.3.3. DVD Multi Drive9.1.7. Removing the ROBSON Cover, Wireless LAN Module and BIOS PCB 9.1.5. Removing the Tilt Panl Ass’y9.1.6. Removing the DIMM Memory Card 9.1.7.1. Wireless LAN Module 9.1.7.2. BIOS PCB9.1.8. Removing the Display unit 9.1.9. Removing the LCD unit, Inverter Ass’y and ANTENNA PWB L,R 9.1.10. Removing the Handle Assy9.1.12.3. Speaker L 9.1.11. Removing the Modem9.1.12.2. Speaker R 9.1.13. Removing the Keyboard9.1.16. Removing the SD PCB 9.1.14. Removing the Top Cover9.1.15. Removing the Pad and TOUCH PAD PCB Cover9.1.19. Removing the PWR BATTERY LED PCB 9.1.17. Removing the WWAN PCB9.1.18. Removing the AUDIO PCB 9.1.22. Removing the Fan Ass’y 9.1.20. Removing the KBD Earth Plate9.1.21. Removing the Hinge Support R Cover PC card9.1.25. Removing the SC RELAY PCB and HDD Hold Plate 9.1.24. Removing the Battery Connector Ass’y9.1.23. Removing the Hinge Support L and MP Hold Plate 9.1.26. Removing the Heat Sink Ass’y9.1.27. Removing the SERIAL PCB 9.1.28. Removing the MAIN HIGH PCB9.2. Reassembly Instructions 9.2.1. Attention when CF-52 series is repaired9.2.2. Setting the MAIN HIGH PCB Setting of Main PCB before assembling S1Insulation S2Bitten S3Sharp Edge S4Part No. Check S5OtherTHERMAL SHEET THERMAL SHEET SCREWTorque of tightening screw 0.18±0.02N・m≒1.8±0.2kgf・cm S4Part No. Check S5Other9.2.3. Setting the SERIAL PCB 9.2.4. Setting the Heat Sink Ass’yHex spacer No.3 9.2.5. Setting the Fan Ass’y How to assemble the Heat Sink Ass’y and Fan Ass’yHDD hold plate 9.2.6. Setting the SC RELAY PCB and HDD Hold PlateSC RELAY PCB No.1S4Part No. Check S5Other 9.2.7. Setting the Battery Connector Ass’y 9.2.8. Setting the Hinge Support L and MP Hold Plate9.2.9. Setting the Hinge Cover R How to place the Cable3. Fix the KBD Earth Plate using the two ScrewsN13 9.2.10. Setting the KBD Earth Plate2. Fix the KBD Earth Plate using the four Screws N4. No.1 to No.4 4. Paste the tape, and connect the FPC to the ConnectorCN349.2.11. Setting the PWR BATTERY LED PCB 9-229.2.12. Setting the AUDIO PCB Arranging the Cable and setting the WL button9.2.13. Setting the WWAN PCB Arranging the Cables and Tapes9.2.14. Setting the SD PCB 9.2.15. Setting the Pad and TOUCH PAD PCB9.2.16. Setting the Top Cover Tape Tape Screws N2 DFHE5122YA 9.2.17. Setting the Keyboard1. Connect the FPCs to the Connector on the KBD FPC 9-27Caution for when assembling the Keyboard 9.2.18. Setting the Speakers 9.2.19. Setting the ModemHow to paste the Tape 9.2.20. Setting the Handle Ass’y 9.2.21. Setting the LCD Unit, Inverter Ass’y and Antenna PWB L, R Schematic for sticking at Point A Using JIGUsing JIG SHIELD SHEET A LCDTAPE The Cable is under the base plate Along the slotAlong the slot LCD DAMPER ESHEET Refer to the specification pictures on the leftSafety Critical Components LCD ASSYPage 9.2.22. Setting the Display Unit, BIOS HIGH PCB and SW LED MDC PCB ScrewN2 DFHE5122YA Screw N4 DRHM0093ZA 6. Fix the SW LED MDC PCB using the six Screws N2. No.1 to No.6Arranging the Cables when assembling the LCD Unit 9-38Page 9.2.23. Setting the Wireless LAN Module, BIOS PCB and ROBSON Cover Arranging the Speaker Cables when assembling the SW LED MDC PCB9.2.24. Setting the DIMM Memory Card and DIMM Cover 9.2.25. Setting the Tilt Panel Ass’yCaution for when assembling the Tilt Panel Ass’y Screw N202 DRSB2+4FKLT9-42 2. Insert the HDD Ass’y into the HDD Damper 9.2.26. Setting the HDD1. Connect the HDD FPC Ass’y to the HDD 3. Set the HDD Ass’y into the HDD Case Upper10 Exploded View CF-52EKMxDxMScrew tightening torque CF-52EKMHDxM with Smart Card Reader and Finger Print Reader only SF2 A SF7 SF3 A SF8 A SF8 SF6 SF4 SF5 SF1A 0.18 ± 0.02 N.m 1.8 ± 0.2 kgf.cm B 0.18 ± 0.01 N.m 1.8 ± 0.1 kgf.cm Screw tightening torque K92-2K92-1 4.4 ± 0.2 kgf.cm CF-52EKMxDxM Replacement Parts ListAccessories REF. NO and AREAPacking Material Mechanical PartsK92-1 K125 Card Reader, Finger Print Reader CF-52EKMHDxMSmart DVD MULTI DRIVEDESCRIPTION MAIN PCB HIGH522, 523, 524, 525 502, 503, 506, 508512, 513, 514, 515 529, 530, 531, 532CAPACITOR, 6.3V, 1µF C 100, 102, 120, 121F1G0J105A001 146, 148, 165, 2421010 CONNECTORCONNECTOR, USB F1G1H181A495IC, USB POWER SW POWER MANAGEMENT SWTICHIC, FET SWITCH IC, SWITCHC0DBDJH00009 DC POWER LINE BEADSDC POWER LINE INDUCTOR IC, LINERB1CFRD000009 B1DHDC000028Q 1001 Q 1004, 1005, 1006RESISTOR, 1/16W, 4.7KO R 103, 107, 363, 365D0GA472JA023 424, 425, 445, 499D0GD1R0JA052 D1BA4530A023D0GA121JA023 RESISTOR, 1/8W, 1OAUDIO PCB TOUCH PAD PCB PWR BATTERY PCBSERIAL PCB SW LED PCBWWAN PCB BIOS PCB HIGHBLUETOOTH PCB WLAN ANTENNA R PCB