Zebra Technologies Q4DLU1B000000, Q3DLUBA000002 manual Proprietary Statement, Product Improvements

Page 2

Proprietary Statement

This manual contains proprietary information of Zebra Technologies Corporation. It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the expressed written permission of Zebra Technologies Corporation.

Product Improvements

Since continuous product improvement is a policy of Zebra Technologies Corporation, all specifications and signs are subject to change without notice.

FCC Compliance Statement

Class B digital devices. Tested to comply with FCC standards for home or office use.

WARNING: Exposure to Radio Frequency radiation. To conform to FCC RF exposure requirements these devices shall be used in accordance with the operating conditions and instructions listed in this manual. Note that there are several radio options available with these printers. Refer to the Users Guide for more complete regulatory information.

NOTE: These units were tested with shielded cables on the peripheral devices. Shielded cables must be used with the units to insure compliance.

Changes or modifications to this unit not expressly approved by Zebra Technologies Corporation could void the user’s authority to operate this equipment.

Canadian Compliance Statement

These Class B digital apparatus comply with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.

“IC:” before the equipment certification number signifies that the Industry Canada technical specifications were met. It does not guarantee that the certified product will operate to the user’s satisfaction.

Agency Approvals and Regulatory Information

• Design certified by CSA

• IP54 Certified

• FCC part 15

• Canadian STD RSS-210

• NOM/NYCE (Mexico)

• EN60950: 2000 Safety Standard

C-Tick (Australia)

• EN55022:1998 Class B European

 

Electromagnetic Radiation Standard

Liability Disclaimer

Inasmuch as every effort has been made to supply accurate information in this manual, Zebra Technologies Corporation is not liable for any erroneous information or omissions. Zebra Technologies Corporation reserves the right to correct any such errors and disclaims

liability resulting therefrom.

No Liability for Consequential Damage

In no event shall Zebra Technologies Corporation or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, damages for loss of business profits, business interruption, loss of business information, or other pecuniary loss) arising out of the use of or the results of use of or inability to use such product, even if Zebra Technologies Corporation has been advised of the possibility of such damages. Because some states do not allow the exclusion of liability for consequential or incidental damages, the above limitation may not apply to you.

Copyrights

The copyrights in this manual and the label print engine described therein are owned by Zebra Technologies Corporation. Unauthorized reproduction of this manual or the software in the label print engine may result in imprisonment of up to one year and fines of up to $10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.

This product may contain ZPL®, ZPL II®, and ZebraLinktm programs; Element Energy Equalizer® Circuit; E3®; and AGFA fonts. Software © ZIH Corp. All rights reserved worldwide.

ZebraLink and all product names and numbers are trademarks, and Zebra, the Zebra logo, ZPL, ZPL II, Element Energy Equalizer Circuit, and E3 Circuit are registered trademarks of ZIH Corp. All rights reserved worldwide.

Monotype®, Intellifont® and UFST® are trademarks of Monotype Imaging, Inc. registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions.

Andy, CG Palacio, CG Century Schoolbook, CG Triumvirate, CG Times, Monotype Kai, Monotype Minchoand Monotype Sungare trademarks of Monotype Imaging, Inc. and may be registered in some jurisdictions. 

HY Gothic Hangulis a trademark of Hanyang Systems, Inc. Angsanais a trademark of Unity Progress Company (UPC) Limited.

Andale®, Arial®, Book Antiqua®, Corsiva®, Gill Sans®, Sorts® and Times New Roman®  are trademarks of The Monotype Corporation registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions.

Century Gothic™, Bookman Old Styleand Century Schoolbookare trademarks of The Monotype Corporation and may be registered in certain jurisdictions.

HGPGothicB is a trademark of the Ricoh company, Ltd. and may be registered in some jurisdictions.

Universis a trademark of Heidelberger Druckmaschinen AG, which may be registered in certain jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly owned subsidiary of Heidelberger Druckmaschinen AG.

Futura® is a trademark of Bauer Types SA registered in the United States Patent and Trademark Office and may be registered in some jurisdictions.

TrueType® is a trademark of Apple Computer, Inc. registered in the United States Patent and Trademark Office and may be registered in certan jurisdictions.

All other brand names, product names, or trademarks belong to their respective holders. ©2008 ZIH Corp.

RMAN-QLS-002 rev.A

• ii •

Image 2
Contents Mobile Printers Proprietary Statement Product ImprovementsContents QL series configurations and Parts Printing Technology DescriptionOperating Modes CommunicationsDiagnostic Tools Introduction to Label VistaSample Configuration Label Printing a Diagnostic LabelCreating a Configuration Label Peripherals installed Configuration Label Example Starting Label Vista Using Label VistaEquipment Required For Label Vista Equipment Required Running The SoftwareAdditional information Using the QL Product Configuration CodeQL Component Replacement Procedures Optional LCD Control Panel TroubleshootingStandard Control Panel Troubleshooting Topics No powerPoor or faded print or flashing RMAN-QLS-002 rev. a Repair Procedures QL220/220 Plus Repair Path QL320 & QL420 Repair Path MLBTools and Supplies Storage and HandlingTools Needed Installing the Media CoverMedia Cover, QL 220- RK18236-1 & QL220 Plus- RK17735-015 Removing the Media CoverRMAN-QLS-002 rev. a Repair Procedures Media Cover, QL 320, QL 320 Plus & QL 420,QL 420 Plus Model Kit p/n CommentsInstalling the Media Cover RMAN-QLS-002 rev. a Repair Procedures Media Guide Plate Assembly, QL220/220 Plus Removing the Media Guide Plate AssemblyInstalling the Media Guide Plate Assembly Installing the Media Assembly Media Guide Assembly, QL320/320 PlusRemoving the Media Assembly Ensure Media Sensor cable is behind holding feature Media Guide Assembly, QL420/420 Plus Kit p/n Description TypeModule Remove the Media Support Disks Install new Media Support DisksMedia Support Disks, QL Series Changing the Media Core Size Changing Media typeMedia Guide Rollers, QL420/QL 420 Plus AN16753-003 Replacing the Media RollersAN16792-009- Installing the Scraper Installing the Gear and PlatenAN16792-008- Installing the Peeler Bar Platen/Gear Kits, QL220/QL 220 Plus AN16972-008Installing the Scraper Platen/Gear Kits, QL320/320 Plus- AN16861-013 & AN16861 014Introduction Replacing the Platen AssemblyPlaten/Gear Kits, QL420/420 Plus- AN16753-021 PreparationRemove the old Platen Assembly Upper Housing /Wireless Modules-QL220 & QL 220 Plus Removing the Upper HousingInstalling the Upper Housing Set New ParametersUpper Housing, QL320- RK18233-1 Installing the Upper HousingUpper Housing, QL420/420 Plus- AN16753-007 Assemble the P.C. Board CoverHousing, Upper p/n DA16394-1 Assemble P.C. Board CoverInstall the Upper Housing Assemble the Sensor Support Remove the Upper HousingLabel Presence Sensor, QL320- AN16861-015 Install Label Present Sensor Option Re-install the Upper HousingInstalling a Wlan Radio and Antenna Install the RadioFinish the Assembly Assemble the AntennaRemoving the Wireless Module QL 320/320 Plus & QL 420/420 Plus Wireless ModulesProcedure Outline Installing the Wireless ModuleUpper Housing or Wireless Module Screw, #4-40 x 3/8 Removing the LCD module Installing the KeypadRemoving the Keypad Installing the LCD module Installing an LCD Keypad Installing a Membrane Key Pad Installing the Printer Frame Printer Frame, QL220/220Plus- AN16972-001Install the new Printer Frame Assembly Removing the Printer FrameRMAN-QLS-002 rev. a Repair Procedures From # of connections CPU Connector # Attach the new Connector Door Connector Door, QL 220 /QL220 Plus AN16972-021Remove the Connector Door Remove the Lower CoverConnector Door, QL420 & QL420 Plus- AN16753-020 Install the Connector DoorInstalling the Motor Motor,QL220 & QL 220 Plus AN16972-002Motor, QL 320/320 Plus & QL420/420 Plus- RK18251-1 Removing the MotorFrom # of connections CPU Connector # Installing the Printhead Printhead, QL220- RK18278-1 & QL 220 Plus- RK17735-016Printhead, QL320 RK18277-1 & QL 320 Plus- RK18465-003 Remove the Printhead Install the new Printhead AssemblyPrinthead, QL 420- RK18252-1 & QL 420 Plus- RK17735-004 RMAN-QLS-002 rev. a Repair Procedures RMAN-QLS-002 rev. a Repair Procedures RMAN-QLS-002 rev. a Repair Procedures RMAN-QLS-002 rev. a Repair Procedures Installing the Latch Latch, QL 220/QL 220 Plus- AN16972-004RMAN-QLS-002 rev. a Repair Procedures Latch, QL 320/ QL 320 Plus- AN16861-025 Latch, QL 420/ QL 420 Plus- AN16753-011 Removing the LatchLatch Assembly Installing the Peeler Shaft and Roller Removing the Peeler Shaft and RollerInstalling the MLB Removing the MLBFrom # of connections MLB Connector # Compatibility Switch SW1 J4 Motor 103 RMAN-QLS-002 rev. a Repair Procedures RMAN-QLS-002 rev. a Repair Procedures 104 105 RMAN-QLS-002 rev. a Repair Procedures RMAN-QLS-002 rev. a Repair Procedures 106 QL220 QL320 Installing the Belt ClipRemoving the Belt Clip QL420AN16753-010 Install the D-Rings AN16753-009 Install the Carrying StrapRemoving the D Rings Installing the D RingsInstalling the Bushings Removing the BushingsInstall the Kickstand QL 220 ilustrated Removing the Battery Pack Installing the Battery PackUsing the Product Configuration Code Component Replacement ProceduresEurope Factory Repair and Parts Ordering ProcedureRepair Services contact Information USA QL 220 Product Configuration Code PCC PCC NotesAccessory Parts not illustrated PCC ExampleQL 220 & 220 Plus Replacement Kits KIT RPR QL2 Media Guide W/BELTShaded items are not illustrated QL 220 & 220 Plus Parts Printer Mechanism Exploded ViewQL 220 & 220 Plus Parts- Unit Exploded View QL 320 & 320 Plus Product Configuration Code PCCInterpreting the PCC Code QL 320 & 320 Plus Replacement Kits Assy Module Irda QL3/4 QLKIT RPR QL 320 Media GUIDE/MW Unit Exploded View Pcmcia Radio Options QL 420 & 420 Plus Product Configuration Code Parts Not Illustrated QL 420 & 420 Plus Replacement Kits KIT Repair QL4 PRINTHD/SENSORSelf TAP SCREW, M3X6, QTY RMAN-QLS-002 rev. a Replacement Kits 130 Pcmcia Option