Zebra Technologies Q3DLUBA000002, Q4DLU1B000000 Set New Parameters, Installing the Upper Housing

Page 39

Installing the Upper Housing

1.Position the Upper Housing onto the Lower Housing. If installing a Wirelss Module (Kits AN 16972-016, -017, or 018) line up the Wireless Module connector with the connector on the MLB.

2.Position the D-Rings between the Upper Housing and Lower Housing as shown and install the (2) 4-40 x 1-1/4 Socket Head Screws.

4.Install the 4-40 x 3/16 Phillipps Screw from the Battery Compartment.3. Install the Battery Pack.

Set New Parameters

If you are replacing a WLAN module, you can now use the Network setup wizards in Label Vista 2.8 or higher. They are found under the Network Setup menu. Again you are urged to refer to the on-line help before you use these wizards, to determine what information you will need to set these parameters.

If you have any questions about network settings you should contact the system admin- istrator for the LAN where the QL series printer will be operating.

Installation of the Bluetooth module allows the advanced user to set many of the Bluetooth parameters through the use of the “get, set, do” commands outlined in Sec- tion 14 of the Programming Manual (revision “L” or higher). These commands are acces- sible only with printer applications of revision 40 or higher.

RMAN-QLS-002 rev. A Repair Procedures

• 2-62 •

Image 39

Contents Mobile Printers Product Improvements Proprietary StatementContents QL series configurations and Parts Communications DescriptionOperating Modes Printing TechnologyIntroduction to Label Vista Diagnostic ToolsPrinting a Diagnostic Label Creating a Configuration LabelSample Configuration Label Peripherals installed Configuration Label Example Using Label Vista Equipment Required For Label VistaStarting Label Vista Running The Software Equipment RequiredUsing the QL Product Configuration Code QL Component Replacement ProceduresAdditional information Troubleshooting Standard Control PanelOptional LCD Control Panel No power Troubleshooting TopicsPoor or faded print or flashing RMAN-QLS-002 rev. a Repair Procedures QL220/220 Plus Repair Path MLB QL320 & QL420 Repair PathStorage and Handling Tools and SuppliesRemoving the Media Cover Installing the Media CoverMedia Cover, QL 220- RK18236-1 & QL220 Plus- RK17735-015 Tools NeededRMAN-QLS-002 rev. a Repair Procedures Model Kit p/n Comments Media Cover, QL 320, QL 320 Plus & QL 420,QL 420 PlusInstalling the Media Cover RMAN-QLS-002 rev. a Repair Procedures Removing the Media Guide Plate Assembly Media Guide Plate Assembly, QL220/220 PlusInstalling the Media Guide Plate Assembly Media Guide Assembly, QL320/320 Plus Removing the Media AssemblyInstalling the Media Assembly Ensure Media Sensor cable is behind holding feature Kit p/n Description Type Media Guide Assembly, QL420/420 PlusModule Install new Media Support Disks Media Support Disks, QL SeriesRemove the Media Support Disks Changing Media type Changing the Media Core SizeReplacing the Media Rollers Media Guide Rollers, QL420/QL 420 Plus AN16753-003Platen/Gear Kits, QL220/QL 220 Plus AN16972-008 Installing the Gear and PlatenAN16792-008- Installing the Peeler Bar AN16792-009- Installing the ScraperPlaten/Gear Kits, QL320/320 Plus- AN16861-013 & AN16861 014 Installing the Scraper Preparation Replacing the Platen Assembly Platen/Gear Kits, QL420/420 Plus- AN16753-021 IntroductionRemove the old Platen Assembly Removing the Upper Housing Upper Housing /Wireless Modules-QL220 & QL 220 PlusSet New Parameters Installing the Upper HousingInstalling the Upper Housing Upper Housing, QL320- RK18233-1Assemble the P.C. Board Cover Upper Housing, QL420/420 Plus- AN16753-007Assemble P.C. Board Cover Housing, Upper p/n DA16394-1Install the Upper Housing Remove the Upper Housing Label Presence Sensor, QL320- AN16861-015Assemble the Sensor Support Re-install the Upper Housing Install Label Present Sensor OptionInstall the Radio Installing a Wlan Radio and AntennaAssemble the Antenna Finish the AssemblyInstalling the Wireless Module QL 320/320 Plus & QL 420/420 Plus Wireless ModulesProcedure Outline Removing the Wireless ModuleUpper Housing or Wireless Module Screw, #4-40 x 3/8 Installing the Keypad Removing the KeypadRemoving the LCD module Installing the LCD module Installing an LCD Keypad Installing a Membrane Key Pad Printer Frame, QL220/220Plus- AN16972-001 Installing the Printer FrameRemoving the Printer Frame Install the new Printer Frame AssemblyRMAN-QLS-002 rev. a Repair Procedures From # of connections CPU Connector # Remove the Lower Cover Connector Door, QL 220 /QL220 Plus AN16972-021Remove the Connector Door Attach the new Connector DoorInstall the Connector Door Connector Door, QL420 & QL420 Plus- AN16753-020Motor,QL220 & QL 220 Plus AN16972-002 Installing the MotorRemoving the Motor Motor, QL 320/320 Plus & QL420/420 Plus- RK18251-1From # of connections CPU Connector # Printhead, QL220- RK18278-1 & QL 220 Plus- RK17735-016 Installing the PrintheadPrinthead, QL320 RK18277-1 & QL 320 Plus- RK18465-003 Install the new Printhead Assembly Printhead, QL 420- RK18252-1 & QL 420 Plus- RK17735-004Remove the Printhead RMAN-QLS-002 rev. a Repair Procedures RMAN-QLS-002 rev. a Repair Procedures RMAN-QLS-002 rev. a Repair Procedures RMAN-QLS-002 rev. a Repair Procedures Latch, QL 220/QL 220 Plus- AN16972-004 Installing the LatchRMAN-QLS-002 rev. a Repair Procedures Latch, QL 320/ QL 320 Plus- AN16861-025 Removing the Latch Latch, QL 420/ QL 420 Plus- AN16753-011Latch Assembly Removing the Peeler Shaft and Roller Installing the Peeler Shaft and RollerRemoving the MLB Installing the MLBFrom # of connections MLB Connector # Compatibility Switch SW1 J4 Motor 103 RMAN-QLS-002 rev. a Repair Procedures RMAN-QLS-002 rev. a Repair Procedures 104 105 RMAN-QLS-002 rev. a Repair Procedures RMAN-QLS-002 rev. a Repair Procedures 106 QL420 Installing the Belt ClipRemoving the Belt Clip QL220 QL320AN16753-009 Install the Carrying Strap AN16753-010 Install the D-RingsRemoving the Bushings Installing the D RingsInstalling the Bushings Removing the D RingsInstall the Kickstand QL 220 ilustrated Installing the Battery Pack Removing the Battery PackComponent Replacement Procedures Using the Product Configuration CodeFactory Repair and Parts Ordering Procedure Repair Services contact Information USAEurope PCC Notes QL 220 Product Configuration Code PCCPCC Example Accessory Parts not illustratedKIT RPR QL2 Media Guide W/BELT QL 220 & 220 Plus Replacement KitsShaded items are not illustrated Printer Mechanism Exploded View QL 220 & 220 Plus PartsQL 220 & 220 Plus Parts- Unit Exploded View PCC QL 320 & 320 Plus Product Configuration CodeInterpreting the PCC Code Assy Module Irda QL3/4 QL QL 320 & 320 Plus Replacement KitsKIT RPR QL 320 Media GUIDE/MW Unit Exploded View Pcmcia Radio Options QL 420 & 420 Plus Product Configuration Code Parts Not Illustrated KIT Repair QL4 PRINTHD/SENSOR QL 420 & 420 Plus Replacement KitsSelf TAP SCREW, M3X6, QTY RMAN-QLS-002 rev. a Replacement Kits 130 Pcmcia Option