Rockford Fosgate 360.6 manual

Page 13

Mount the fuseholder within 18" of the battery using two (2) #8 screws. Disassemble the fuseholder. You should have 2 black plastic end caps, 2 gold-plated fuse clips, a plastic spacer and the fuseholder body. Trim the amplifier power cable to reach the fuseholder and strip the wire 3/8". Slide one of the end caps over the wire (narrow end first) and insert the wire into one of the fuse clips. Tighten the set screw. Screw the black end cap to the fuseholder body to secure the cable. Use the section of cable that was trimmed earlier and connect it to the other end of the fuseholder. Install the plastic spacer in the fuseholder and attach the cable to the fuseholder body.

NOTE: The B+ cable MUST be fused 18" or less from the vehicle's battery. Install the fuseholder under the hood and prepare the cable ends as stated above. Connections should be water tight.

4.Strip 3/8" from the battery end of the power cable and crimp a large ring terminal to the cable. Use the ring terminal to connect to the battery positive terminal. Do not install the fuse at this time.

5.Prepare a length of cable to be used for the GND connection. Strip 5/8" of insulation from the end of the cable as described previously and connect to the appropriate terminal of the amplifier. Prepare the chassis ground by scraping any paint from the metal surface and thoroughly clean the area of all dirt and grease. Strip the other end of the wire and attach a ring connector. Fasten the cable to the chassis using a non-anodized screw and a star washer.

6.Prepare the REM turn-on wire for connection to the amplifier by stripping 1/4" of insulation from the wire end and crimping an insulated spade connector in place. Slide the connector over the REM terminal on the amplifier. Connect the other end of the REM wire to a switched 12 volt positive source. The switched signal is usually taken from the source unit's auto antenna or the accessory lead. If the source unit does not have these outputs available, the recommended solution is to wire a mechanical switch in line with a 12 volt source to activate the amplifier.

7.Securely mount the amplifier (with supplied screws) to the vehicle or amp rack. Be careful not to mount the amplifier on cardboard or plastic panels. Doing so may enable the screws to pull out from the panel due to road vibration or sudden vehicle stops.

– 10 –

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Punch Practice Safe Sound T T I N G S T a R T E D TA B L E O F CO N T E N T ST R O D U C T I O N Accessory PackTransana Technical Design FeaturesDSM Discrete Surface Mount Technology Mosfet Devices LED Design FeaturesXCard C XCard B XCard a S TA L L AT I O N CO N S I D E R AT I O N S Trunk Mounting Mounting LocationWI R I N G T H E SY S T E M Battery and ChargingPage Page Customizing T H E Xcard US I N G T H E XcardButterworth Alignment Q = Resistor ChartConfigure a 12dB/octave filter for Channel a Xcard ConfigurationsConfigure a 12dB/octave filter for Channel B Configure a 12dB/octave Bandpass filter for Channel B Configure a 24dB/octave filter for Channel BConfigure a 12dB/octave Low-Pass filter for Channel C Using the Phase SwitchPhase Switch set to Configuration #1 Using the Signal Switching NetworkDefault Factory Setting Configuration #2 Configuration #4Configuration #5 Default Factory Setting B B a a Configuration #3 Gain Ch. C Ch. B Ch. a + R Ch. C CA a Mono Power Connections Option #1 InstallationPower Connections Option #2 Channel Operation Channel Mono Operation Channel Stereo Operation Ohm min + L Ohm min + REM Dual B+ Dual GND Ch. B SY S T E M DI a G R a M S Front & Rear w/Bridged Subwoofer Front & Rear w/Bridged Subwoofer Bridged Front & Rear w/MidbassSubwoofer Remedy TR O U B L E S H O O T I N GDiagnosis Remedy Engine Noise DY N a M I C PO W E R ME a S U R E M E N T S About the Dynamic Power MeasurementsMusic Listening to Loudspeakers Not ResistorsInformation Cubed What is an Amplifier?AGU E C I F I C AT I O N SWA R R a N T Y in F O R M AT I O N Length of WarrantyPage Terminal B+ InstalacionTerminal GND Terminal REMConfiguración n2 Configuración n1Configuración n3 Configuración n4Configuración n6 Canal C puente Configuración n5Funcionamiento en tres canales Funcionamiento en 6 canales Estereo Introduction InstallationUtilisation DU Réseau DE Commutation DU Signal Configuration #6 Les controles de gain des canaux C sont indépendants Configuration à 3 canauxConfiguration à 6 canaux + Anschluss EinbauGND Anschluss REM AnschlussBeispiel #1 Benutzen DES Signal NetzwerkesBeispiel #2 Beispiel #3Beispiel #6 Beispiel #5Kanal Operation Kanal Stereo Operation Terminale B+ cavo positivo InstallazioneTerminale GND cavo negativo Terminale REM Consenso di accensioneConfigurazione #2 Configurazione #1Configurazione #4 Impiegare LA Rete DI Selezione Degli IngressiConfigurazione #6 E-Z bridge Uscita C Configurazione #5Funzionamento a 3 canali Funzionamento a 6 canali stereo Page Page Made in the USA

360.6 specifications

The Rockford Fosgate 360.6 is a sophisticated digital signal processor (DSP) designed to elevate the audio experience in vehicles. As part of Rockford Fosgate's commitment to high-quality sound, the 360.6 provides users with extensive control over their audio setup, making it an ideal choice for both audiophiles and casual listeners alike.

One of the standout features of the 360.6 is its impressive 6-channel processing capability. With six channels of input and output, this DSP allows for intricate control over multiple speakers and subwoofers, ensuring optimal sound distribution throughout the vehicle. This flexibility means that users can fine-tune their audio systems to suit their personal preferences and vehicle acoustics.

In addition to its channel configuration, the 360.6 is equipped with a range of audio tuning options. It includes a 30-band graphic equalizer, allowing users to adjust frequency response with precision. This feature enables users to enhance or minimize specific frequencies for a truly customized sound experience. Furthermore, the device supports time alignment, which helps to synchronize audio signals, providing a cohesive listening experience regardless of where the listener is located in the vehicle.

The Rockford Fosgate 360.6 also features an onboard Bluetooth connection, facilitating wireless streaming of music from smartphones and other devices. This modern connectivity option is complemented by the inclusion of AUX inputs and optical digital inputs, ensuring compatibility with various devices and audio sources.

Another notable characteristic of the 360.6 is its user-friendly interface, accessed through a dedicated software application. This allows users to configure settings, adjust parameters, and save custom presets effortlessly. The DSP can also be updated via firmware updates, ensuring compatibility with the latest audio technologies and features.

Durability is another hallmark of the Rockford Fosgate brand, and the 360.6 is no exception. Built with high-quality materials, it is designed to withstand the rigors of automotive environments while delivering consistent performance.

In conclusion, the Rockford Fosgate 360.6 is a powerful audio processing solution that combines advanced technology with ease of use. With its 6-channel processing, comprehensive tuning options, Bluetooth connectivity, and robust build, it stands out as an essential component for anyone looking to achieve premium sound quality in their vehicle. Whether you’re looking to enhance your car audio system or simply enjoy your favorite tunes on the road, the Rockford Fosgate 360.6 delivers an unparalleled listening experience.
Top Page Image Contents