Rockford Fosgate 360.6 manual Transana, Technical Design Features

Page 5

TECHNICAL DESIGN FEATURES

◆TRANS•ANA

(TRANSconductance Active Nodal Amplifier)

The TRANS•ANA (TRANSconductance Active Nodal Amplifier) is a circuit that allows the audio signal to pass through the amplifier at low voltage. The signal is directly level-shifted to the fixed high voltage rails via a pair of driver transistors. Signal linearity is assured by an active node formed by the drive transistors at ultrasonic frequencies. This allows amplifier performance similar to trans•nova which is highly stable and linear while utilizing the advantages of a non- floating power supply.

THE RESULT: An extended frequency bandwidth accurately supplied to the output stages of the amplifier.

◆TOPAZ (Tracking Operation Pre-Amplifier Zone)

The TOPAZ (Tracking Operation Pre-Amplifier Zone) circuitry solves ground loop noise problems common to automotive amplifier design. This innovative new development allows vastly improved isolation of the input signal grounds from the power supply ground of the amplifier. This is accomplished by allowing the source unit to control the potential “environment” of the entire input structure or “zone” of the amplifier. This process improves the noise rejection of the ampli- fier by 30-40dB – an astounding 30-100 times better than amplifiers without TOPAZ.

THE RESULT: Elimination of troublesome ground loop noise between source and amplifier.

◆Bass EQ

The Bass EQ helps correct for acoustical deficiencies in the listening environment. A unique potentiometer that controls bass compen- sates for the lack of low frequencies present in most car environ- ments. Unlike a conventional tone control, the Bass EQ corrects the specific problem of poor low bass response.

THE RESULT: Provides better low bass response.

– 2 –

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Punch Practice Safe Sound T T I N G S T a R T E D TA B L E O F CO N T E N T ST R O D U C T I O N Accessory PackTransana Technical Design FeaturesDSM Discrete Surface Mount Technology Mosfet Devices LED Design FeaturesXCard C XCard B XCard a S TA L L AT I O N CO N S I D E R AT I O N S Trunk Mounting Mounting LocationWI R I N G T H E SY S T E M Battery and ChargingPage Page Customizing T H E Xcard US I N G T H E XcardButterworth Alignment Q = Resistor ChartConfigure a 12dB/octave filter for Channel B Xcard ConfigurationsConfigure a 12dB/octave filter for Channel a Configure a 12dB/octave Bandpass filter for Channel B Configure a 24dB/octave filter for Channel BPhase Switch set to Using the Phase SwitchConfigure a 12dB/octave Low-Pass filter for Channel C Configuration #1 Using the Signal Switching NetworkDefault Factory Setting Configuration #2 Configuration #4Configuration #5 Default Factory Setting B B a a Configuration #3 Gain Ch. C Ch. B Ch. a + R Ch. C CA a Mono Power Connections Option #2 InstallationPower Connections Option #1 Channel Operation Channel Mono Operation Channel Stereo Operation Ohm min + L Ohm min + REM Dual B+ Dual GND Ch. B SY S T E M DI a G R a M S Front & Rear w/Bridged Subwoofer Front & Rear w/Bridged Subwoofer Subwoofer Front & Rear w/MidbassBridged Remedy TR O U B L E S H O O T I N GDiagnosis Remedy Engine Noise DY N a M I C PO W E R ME a S U R E M E N T S About the Dynamic Power MeasurementsMusic Listening to Loudspeakers Not ResistorsInformation Cubed What is an Amplifier?AGU E C I F I C AT I O N SWA R R a N T Y in F O R M AT I O N Length of WarrantyPage Terminal B+ InstalacionTerminal GND Terminal REMConfiguración n2 Configuración n1Configuración n3 Configuración n4Configuración n6 Canal C puente Configuración n5Funcionamiento en tres canales Funcionamiento en 6 canales Estereo Introduction InstallationUtilisation DU Réseau DE Commutation DU Signal Configuration #6 Les controles de gain des canaux C sont indépendants Configuration à 3 canauxConfiguration à 6 canaux + Anschluss EinbauGND Anschluss REM AnschlussBeispiel #1 Benutzen DES Signal NetzwerkesBeispiel #2 Beispiel #3Beispiel #6 Beispiel #5Kanal Operation Kanal Stereo Operation Terminale B+ cavo positivo InstallazioneTerminale GND cavo negativo Terminale REM Consenso di accensioneConfigurazione #2 Configurazione #1Configurazione #4 Impiegare LA Rete DI Selezione Degli IngressiConfigurazione #6 E-Z bridge Uscita C Configurazione #5Funzionamento a 3 canali Funzionamento a 6 canali stereo Page Page Made in the USA

360.6 specifications

The Rockford Fosgate 360.6 is a sophisticated digital signal processor (DSP) designed to elevate the audio experience in vehicles. As part of Rockford Fosgate's commitment to high-quality sound, the 360.6 provides users with extensive control over their audio setup, making it an ideal choice for both audiophiles and casual listeners alike.

One of the standout features of the 360.6 is its impressive 6-channel processing capability. With six channels of input and output, this DSP allows for intricate control over multiple speakers and subwoofers, ensuring optimal sound distribution throughout the vehicle. This flexibility means that users can fine-tune their audio systems to suit their personal preferences and vehicle acoustics.

In addition to its channel configuration, the 360.6 is equipped with a range of audio tuning options. It includes a 30-band graphic equalizer, allowing users to adjust frequency response with precision. This feature enables users to enhance or minimize specific frequencies for a truly customized sound experience. Furthermore, the device supports time alignment, which helps to synchronize audio signals, providing a cohesive listening experience regardless of where the listener is located in the vehicle.

The Rockford Fosgate 360.6 also features an onboard Bluetooth connection, facilitating wireless streaming of music from smartphones and other devices. This modern connectivity option is complemented by the inclusion of AUX inputs and optical digital inputs, ensuring compatibility with various devices and audio sources.

Another notable characteristic of the 360.6 is its user-friendly interface, accessed through a dedicated software application. This allows users to configure settings, adjust parameters, and save custom presets effortlessly. The DSP can also be updated via firmware updates, ensuring compatibility with the latest audio technologies and features.

Durability is another hallmark of the Rockford Fosgate brand, and the 360.6 is no exception. Built with high-quality materials, it is designed to withstand the rigors of automotive environments while delivering consistent performance.

In conclusion, the Rockford Fosgate 360.6 is a powerful audio processing solution that combines advanced technology with ease of use. With its 6-channel processing, comprehensive tuning options, Bluetooth connectivity, and robust build, it stands out as an essential component for anyone looking to achieve premium sound quality in their vehicle. Whether you’re looking to enhance your car audio system or simply enjoy your favorite tunes on the road, the Rockford Fosgate 360.6 delivers an unparalleled listening experience.
Top Page Image Contents