Rockford Fosgate 250.2 manual Mono

Page 10

250.1 DESIGN FEATURES

1.Cast Aluminum Chrome Heatsink – The cast aluminum heatsink of the Punch Power amplifier dissipates heat generated by the amplifier's circuitry. The inherent advantage of casting provides a 30% improvement of cooling over conventional extrusion heatsink designs.

2.End Caps – The unique end caps conceal the wiring and input cables, giving the amplifier a clean “stealth” look.

 

 

6

9

13

7

12

11

 

 

L (Mono)

R

Power

 

 

 

 

 

 

 

 

 

 

Speaker

Gain

 

 

X-Over

0°-180°

 

 

24dB/12dB/0dB

 

+

L

 

 

 

 

 

 

L + R / L

 

 

 

 

 

 

 

 

 

 

 

L Pass-Thru

R Pass-Thru

 

(Mono)

 

 

 

 

 

 

 

 

 

3

8

 

 

 

 

 

 

 

REM

Dual B+

 

Dual GND

 

 

 

 

 

 

 

 

5

4

 

4

 

 

3.Speaker Terminals – The heavy duty, gold-plated terminal block connectors (+ and –) will accept wire sizes from 8 AWG to 18 AWG. These gold-plated connectors are immune to corrosion that can cause signal deterioration.

4.Power Terminals – The dual power and ground connectors on the Punch Power amplifier are gold-plated and will accommodate up to two 8 AWG wires maximizing the input current capability of the amplifier.

5.REM Terminal – This gold-plated spade terminal is used for the AP (auto power) or remote turn on of the Punch 250.1 Power amplifier.

6.RCA Input Jacks – The industry standard RCA jack provides an easy connection for signal level input. They are gold- plated to resist the signal degradation caused by corrosion.

7.Summed Stereo / Mono Switch – This switch is used to select whether 1 or 2 signal inputs will be used to drive the amplifier.

8.Pass-Thru RCA Jacks – The Pass-Thru provides a convenient source for daisychaining an additional amplifier.This eliminates the need for additional RCA cables or “Y” adapters. The Pass-Thru output is Full Range only.

9.Input Sensitivity Control – The input level control is preset to match the output of most source units. It can be adjusted to match output levels from a variety of source units.

– 7 –

Image 10
Contents Punch Practice Safe Sound Serial Number Model NumberTable of Contents T T I N G S TA R T E DPunch Amplifier Accessory Pack Introduction to 250 SeriesTechnical Design Features Transnova TRANSconductance NOdal Voltage AmplifierStereo Pass-Thru Balanced Line Inputs Result Quiet transmission of audio from source to amplifierDesign Features 250 Mono 1AMPLIFIER Installation Considerations Tools NeededBattery and Charging Mounting Location SWiring the System Using Passive Crossovers Table of Crossover Component Values 6dB/Octave High-Pass and Low-Pass Filters3386 Using the XcardCustomizing the Xcard 7234Xcard Resistor Chart Power Connections Option #1 InstallationPower Connections Option #2 Stereo Operation Stereo/Mono OperationBridged Operation EZ-Bridged OperationUsing the 250.2 Signal Switching Network AmplifierXCard not required Uses output from XCard Pass-Thruuses output from XCard Pass Thru XCard Audiophile Bypass the Pass-Thru Using the 250.2 Balanced Line Inputs Connecting the BLTDisconnect Speakers from AC Voltmeter set to AC VoltsKeep ground connections as close to each other as possible Mono Operation Stereo Operation using two Punch 250.1 Power Amplifiers 250 #1 250 #2XCard 250.1 #1/#2 set to Full Range Bridged Mono Operation US I N G T H E 250.1 Signal SW I T C H I N G NE T W O R K Audiophile BypassConfigure a 12dB per octave filter for Xover is set to 12dB Pass-Thruhas Full Range output onlyConfigure a 24dB per octave filter for the 250 Total Power Delivery RMS System DiagramsWatt System rated @ 4 ohms 12dB/octave HP Woofers12dB/octave BP Total Power Delivery RMS Tweeters 450 Rockford Fosgate Accessories Balanced Line Transmitter FG-BLTXCard Crossovers Energy Storage CapacitorsRecommended capacitance is 1 farad per 1000 watts Amplifier does not turn on TroubleshootingSymptom Diagnosis Remedy Amplifier has no soundAmplifier Noise Speaker Output LowOr Distorted No output from Pass-ThruSource unit output too low Repair or replace original source as NeededQuick Check for Troubleshooting CAR Audio Systems Autosound 2000sTime for Processors Monthly magazine for the technically inclinedDynamic Power Measurements Specifications Watts1420 420 Watts710 Watts 500 WattsLimited Warranty Information R M a T I O N Introducción Ubicación DE LOS AmplificadoresEspañol Operación mono/estéreoIntroduction MontageOpération stéréo/mono Tri- mode Einleitung EinbauortLinken Phasen Schalter auf 0 stellen Stereo/Mono BetriebTerminale B+ cavo positivo IntroduzioneDove Posizionarlo Terminale GND cavo negativoStereo/Mono Operation Fase sinistra dellinterruttore posizionata suMade in the USA

250.2 specifications

The Rockford Fosgate 250.2 is a powerful and versatile car amplifier known for its performance and reliability. As part of Rockford Fosgate’s renowned line of audio equipment, the 250.2 is engineered to enhance the listening experience in vehicles, providing a fantastic balance of power, clarity, and durability.

This amplifier delivers an impressive 250 watts of power, making it suitable for both beginner audiophiles and seasoned enthusiasts who seek to elevate their car audio system. The 250.2 is a two-channel amplifier, which means it can power two speakers or one subwoofer. Utilizing a class A/B topology, it ensures high efficiency while minimizing distortion, resulting in clean and powerful audio output.

One of the standout features of the Rockford Fosgate 250.2 is its Signal Sense turn-on technology. This feature allows the amplifier to automatically turn on when it detects a signal from the head unit, eliminating the need for a manual switch. Additionally, the built-in remote gain control allows users to adjust the amplifier’s output level easily, providing a customizable audio experience tailored to their preferences.

The 250.2 is equipped with an adjustable crossover that can be set to high-pass, low-pass, or full-range modes. This flexibility permits users to fine-tune the frequencies sent to their speakers, optimizing sound quality and performance. Further enhancing its capabilities, the amplifier also includes built-in variable bass boost that allows users to amplify low frequencies for a more impactful bass response.

Constructed with a durable aluminum heatsink, the Rockford Fosgate 250.2 maintains optimal temperature during operation, ensuring long-lasting performance and minimizing thermal issues. The amplifier also features RCA inputs, making it compatible with a wide range of audio sources, enhancing its versatility for various setups.

In summary, the Rockford Fosgate 250.2 is a reliable and robust car amplifier that combines high power output with advanced technologies and user-friendly features. Its efficient design, customizable settings, and quality construction make it an excellent choice for anyone looking to improve their vehicle's sound system. Whether for day-to-day driving or road trips, the Rockford Fosgate 250.2 provides an audio experience that is both powerful and enjoyable, reinforcing Rockford Fosgate's reputation as a leader in the car audio industry.