Wiring the System

Rockford Fosgate 250.2 manual Wiring the System

CAUTION: Avoid running power wires near the low level input cables, antenna, power leads, sensitive equipment or harnesses. The power wires carry substantial current and could induce noise into the audio system.

1.Configure the internal XCard crossovers prior to installation. Refer to the “Using the Signal Switching Network” (page 19 for the 250.2 and page 31 for 250.1) for further information.

2.Plan the wire routing. Take care when running signal level RCA cables to keep them close together but isolated from the amplifier's power cables and any high power auto accessories, especially electric motors. This is done to prevent coupling the noise from radiated electrical fields into the audio signal. When feeding the wires through the firewall or any metal barrier, protect them with plastic or rubber grommets to prevent short circuits. Leave the wires long at this point to adjust for a precise fit at a later time.

3.Prepare the Power cable for attachment to the amplifier by stripping 5/8" of insulation from the end of the wire. The use of 8 gauge power cable can interfere with the installation of the end caps. Proper wire dress can prevent

this from occurring. To prevent the wire from fraying, strip the insulation at a 45° angle. Insert the bared wire into the B+ terminal with the long side of the insulation on the top. Bend the cable down at a 90° angle. Tighten

the set screw to secure the cable in place. We recommend using (2) 8 gauge cables for power and for ground. This will give you the best performance possible.

STRIP WIRE

5/8"

AMP

INSULATION

4.Strip 3/8" from the battery end of the power cable and crimp a large ring terminal to the cable. Use the ring terminal to connect to the battery positive terminal. Do not install the fuse at this time.

5.Prepare a length of cable to be used for the ground connection. Strip 5/8" of insulation from the end of the cable as described above and connect to the appropriate terminal of the amplifier. Prepare the chassis ground by scraping any paint from the metal surface and thoroughly clean the area of all dirt and grease. Strip the other end of the wire and attach a ring connector. Fasten the cable to the chassis using a non-anodized screw and a star washer.

6.Prepare the REM turn-on wire for connection to the amplifier by stripping 1/4" of insulation from the wire end and crimping an insulated spade connector in place. Slide the connector over the REM terminal on the amplifier. Connect the other end of the REM wire to a switched 12 volt positive source. The switched signal is usually taken from the source unit's auto antenna or the accessory lead. If the source unit does not have these outputs available, the recommended solution is to wire a mechanical switch in line with a 12 volt source to activate the amplifier.

7.Securely mount the amplifier (with supplied screws) to the vehicle or amp rack. Be careful not to mount the amplifier on cardboard or plastic panels. Doing so may enable the screws to pull out from the panel due to road vibrations or sudden vehicle stops.

8.Connect the source signal to the amplifier by plugging the RCA cables into the input jack(s) at the amplifier. If using Balanced Line Inputs, refer to page 24.

9.Connect the speakers. Strip the speaker wires 5/8" and insert into the appropriate terminal on the amplifier. Insert the bared wire into the speaker terminal and tighten the set screw to secure into place. Be sure to maintain proper speaker polarity. DO NOT chassis ground any of the speaker leads as unstable operation may result.

– 11 –

250.2 specifications

The Rockford Fosgate 250.2 is a powerful and versatile car amplifier known for its performance and reliability. As part of Rockford Fosgate’s renowned line of audio equipment, the 250.2 is engineered to enhance the listening experience in vehicles, providing a fantastic balance of power, clarity, and durability.

This amplifier delivers an impressive 250 watts of power, making it suitable for both beginner audiophiles and seasoned enthusiasts who seek to elevate their car audio system. The 250.2 is a two-channel amplifier, which means it can power two speakers or one subwoofer. Utilizing a class A/B topology, it ensures high efficiency while minimizing distortion, resulting in clean and powerful audio output.

One of the standout features of the Rockford Fosgate 250.2 is its Signal Sense turn-on technology. This feature allows the amplifier to automatically turn on when it detects a signal from the head unit, eliminating the need for a manual switch. Additionally, the built-in remote gain control allows users to adjust the amplifier’s output level easily, providing a customizable audio experience tailored to their preferences.

The 250.2 is equipped with an adjustable crossover that can be set to high-pass, low-pass, or full-range modes. This flexibility permits users to fine-tune the frequencies sent to their speakers, optimizing sound quality and performance. Further enhancing its capabilities, the amplifier also includes built-in variable bass boost that allows users to amplify low frequencies for a more impactful bass response.

Constructed with a durable aluminum heatsink, the Rockford Fosgate 250.2 maintains optimal temperature during operation, ensuring long-lasting performance and minimizing thermal issues. The amplifier also features RCA inputs, making it compatible with a wide range of audio sources, enhancing its versatility for various setups.

In summary, the Rockford Fosgate 250.2 is a reliable and robust car amplifier that combines high power output with advanced technologies and user-friendly features. Its efficient design, customizable settings, and quality construction make it an excellent choice for anyone looking to improve their vehicle's sound system. Whether for day-to-day driving or road trips, the Rockford Fosgate 250.2 provides an audio experience that is both powerful and enjoyable, reinforcing Rockford Fosgate's reputation as a leader in the car audio industry.